scholarly journals Modeling and simulation of forces applied to the horizontal axis wind turbine rotors by the vortex method coupled with the method of the blade element

2021 ◽  
Vol 12 (1) ◽  
pp. 413
Author(s):  
Ibtissem Barkat ◽  
Abdelouahab Benretem ◽  
Fawaz Massouh ◽  
Issam Meghlaoui ◽  
Ahlem Chebel
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Wind Farms ◽  
Vortex Method ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Rotor Blades ◽  
Good Representation ◽  
Horizontal Axis Wind Turbine ◽  
Blade Element

This article aims to study the forces applied to the rotors of horizontal axis wind turbines. The aerodynamics of a turbine are controlled by the flow around the rotor, or estimate of air charges on the rotor blades under various operating conditions and their relation to the structural dynamics of the rotor are critical for design. One of the major challenges in wind turbine aerodynamics is to predict the forces on the blade as various methods, including blade element moment theory (BEM), the approach that is naturally adapted to the simulation of the aerodynamics of wind turbines and the dynamic and models (CFD) that describes with fidelity the flow around the rotor. In our article we proposed a modeling method and a simulation of the forces applied to the horizontal axis wind rotors turbines using the application of the blade elements method to model the rotor and the vortex method of free wake modeling in order to develop a rotor model, which can be used to study wind farms. This model is intended to speed up the calculation, guaranteeing a good representation of the aerodynamic loads exerted by the wind.

scholarly journals Geometrical Design of a Rotor Blade for a Small Scale Horizontal Axis Wind Turbine

2019 ◽  
Vol 8 (3) ◽  
pp. 3390-3400
Keyword(s):  
Wind Turbine ◽  
Rotor Blade ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Small Scale ◽  
Horizontal Axis Wind Turbine ◽  
Geometrical Properties ◽  
Momentum Theory ◽  
Bem Theory ◽  
Blade Element

In the present study, Blade Element Momentum theory (BEMT) has been implemented to heuristically design a rotor blade for a 2kW Fixed Pitch Fixed Speed (FPFS) Small Scale Horizontal Axis Wind Turbine (SSHAWT). Critical geometrical properties viz. Sectional Chord ci and Twist distribution θTi for the idealized, optimized and linearized blades are analytically determined for various operating conditions. Results obtained from BEM theory demonstrate that the average sectional chord ci and twist distribution θTi of the idealized blade are 20.42% and 14.08% more in comparison with optimized blade. Additionally, the employment of linearization technique further reduced the sectional chord ci and twist distribution θTi of the idealized blade by 17.9% and 14% respectively, thus achieving a viable blade bounded by the limits of economic and manufacturing constraints. Finally, the study also reveals that the iteratively reducing blade geometry has an influential effect on the solidity of the blade that in turn affects the performance of the wind turbine.

Inclusion of a Simple Dynamic Inflow Model in the Blade Element Momentum Theory for Wind Turbine Application

2014 ◽  
Author(s):  
Xiaomin Chen ◽  
Ramesh Agarwal
Keyword(s):  
Steady State ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Turbine Blades ◽  
Operating Conditions ◽  
Phase Iii ◽  
Speed Ratio ◽  
Horizontal Axis Wind Turbine ◽  
Bem Theory ◽  
Blade Element

It is well established that the power generated by a Horizontal-Axis Wind Turbine (HAWT) is a function of the number of blades B, the tip speed ratio λr (blade tip speed/wind free-stream velocity) and the lift to drag ratio (CL/CD) of the airfoil sections of the blade. The previous studies have shown that Blade Element Momentum (BEM) theory is capable of evaluating the steady-state performance of wind turbines, in particular it can provide a reasonably good estimate of generated power at a given wind speed. However in more realistic applications, wind turbine operating conditions change from time to time due to variations in wind velocity and the aerodynamic forces change to new steady-state values after the wake settles to a new equilibrium whenever changes in operating conditions occur. The goal of this paper is to modify the quasi-steady BEM theory by including a simple dynamic inflow model to capture the unsteady behavior of wind turbines on a larger time scale. The output power of the wind turbines is calculated using the improved BEM method incorporating the inflow model. The computations are performed for the original NREL Phase II and Phase III turbines and the Risoe turbine all employing the S809 airfoil section for the turbine blades. It is shown by a simple example that the improved BEM theory is capable of evaluating the wind turbine performance in practical situations where operating conditions often vary in time.

scholarly journals Kharitonov Theorem Based Robust Stability Analysis of a Wind Turbine Pitch Control System

Mathematics ◽  
2020 ◽  
Vol 8 (6) ◽  
pp. 964 ◽  
Author(s):  
Aitor Saenz-Aguirre ◽  
Ekaitz Zulueta ◽  
Unai Fernandez-Gamiz ◽  
Daniel Teso-Fz-Betoño ◽  
Javier Olarte
Keyword(s):  
Stability Analysis ◽  
Wind Turbine ◽  
Robust Stability ◽  
Wind Turbines ◽  
Energy Generation ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Horizontal Axis Wind Turbine ◽  
Robust Stability Analysis ◽  
Different Characteristics

Wind energy has recently become one of the most prominent technologies among electrical energy generation systems. As a result, wind-based renewable energy generation systems are incessantly growing, and wind turbines of different characteristics are being installed in many locations around the world. One drawback associated with different characteristics of the wind turbines is that controllers have to be designed individually for each of them. Additionally, stable performance of the wind turbines needs to be ensured in the whole range of their operating conditions. Nowadays, there are many causes for uncertainties in the actual performance of a horizontal axis wind turbine, such as variations in the characteristics of the wind turbine, fabrication tolerances of its elements or non-linearities related to different operating-points. Hence, in order to respond to these uncertainties and ensure the stability of the wind turbine, robust control and stability theories have been gaining importance during recent years. Nevertheless, the use of robust stability analyses with complex wind turbine models still needs to be faced and remarkably improved. In this paper, a stability analysis of the pitch system control of a horizontal axis wind turbine based on the Kharitonov robust stability method is proposed. The objective was to assess the robust stability of a pitch controller in response to uncertainties arising from varying operating conditions of the National Renewable Energies Laboratory (NREL) 5 MW class IIA wind turbine. According to the results, the proposed method could satisfactorily respond to limited variations in the characteristics of the model, but could lack accuracy in cases of bigger variations or employment of high order complex mathematical models.

scholarly journals Prognostics-based adaptive control strategy for lifetime control of wind turbines

2021 ◽  
Author(s):  
Edwin Kipchirchir ◽  
Manh Hung Do ◽  
Jackson Githu Njiri ◽  
Dirk Söffker
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Control Strategy ◽  
Fatigue Loading ◽  
Operational Reliability ◽  
Operating Conditions ◽  
Rotor Blades ◽  
Time Step ◽  
Damage Level ◽  
Structural Loading

Abstract. Variability of wind profiles in both space and time is responsible for fatigue loading in wind turbine components. Advanced control methods for mitigating structural loading in these components have been proposed in previous works. These also incorporate other objectives like speed and power regulation for above-rated wind speed operation. In recent years, lifetime control and extension strategies have been proposed to guaranty power supply and operational reliability of wind turbines. These control strategies typically rely on a fatigue load evaluation criteria to determine the consumed lifetime of these components, subsequently varying the control set-point to guaranty a desired lifetime of the components. Most of these methods focus on controlling the lifetime of specific structural components of a wind turbine, typically the rotor blade or tower. Additionally, controllers are often designed to be valid about specific operating points, hence exhibit deteriorating performance in varying operating conditions. Therefore, they are not able to guaranty a desired lifetime in varying wind conditions. In this paper an adaptive lifetime control strategy is proposed for controlled ageing of rotor blades to guaranty a desired lifetime, while considering damage accumulation level in the tower. The method relies on an online structural health monitoring system to vary the lifetime controller gains based on a State of Health (SoH) measure by considering the desired lifetime at every time-step. For demonstration, a 1.5 MW National Renewable Energy Laboratory (NREL) reference wind turbine is used. The proposed adaptive lifetime controller regulates structural loading in the rotor blades to guaranty a predefined damage level at the desired lifetime without sacrificing on the speed regulation performance of the wind turbine. Additionally, significant reduction in the tower fatigue damage is observed.

scholarly journals Efficient contribution of partially tip cascaded horizontal-axis wind turbine

2019 ◽  
Vol 11 (11) ◽  
pp. 168781401989211
Author(s):  
Deyaa Nabil Elshebiny ◽  
Ali AbdelFattah Hashem ◽  
Farouk Mohammed Owis
Keyword(s):  
Wind Turbine ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
National Renewable Energy Laboratory ◽  
Horizontal Axis Wind Turbine ◽  
Ansys Fluent ◽  
Knowing That ◽  
Turbine Performance ◽  
Blade Tip

This article introduces novel blade tip geometric modification to improve the aerodynamic performance of horizontal-axis wind turbine by adding auxiliary cascading blades toward the tip region. This study focuses on the new turbine shape and how it enhances the turbine performance in comparison with the classical turbine. This study is performed numerically for National Renewable Energy Laboratory Phase II (non-optimized wind turbine) taking into consideration the effect of adding different cascade configurations on the turbine performance using ANSYS FLUENT program. The analysis of single-auxiliary and double-auxiliary cascade blades has shown an impact on increasing the turbine power of 28% and 76%, respectively, at 72 r/min and 12.85 m/s of wind speed. Knowing that the performance of cascaded wind turbine depends on the geometry, solidity and operating conditions of the original blade; therefore, these results are not authorized for other cases.

scholarly journals Comparison of horizontal axis wind turbine (HAWT) and vertical axis wind turbine (VAWT)

2018 ◽  
Vol 7 (4.13) ◽  
pp. 74 ◽  
Author(s):  
Muhd Khudri Johari ◽  
Muhammad Azim A Jalil ◽  
Mohammad Faizal Mohd Shariff
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Green Technology ◽  
Horizontal Axis ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Current Output ◽  
Voltage Output ◽  
And Performance

As the demand for green technology is rising rapidly worldwide, it is important that Malaysian researchers take advantage of Malaysia’s windy climates and areas to initiate more power generation projects using wind. The main objectives of this study are to build a functional wind turbine and to compare the performance of two types of design for wind turbine under different speeds and behaviours of the wind. A three-blade horizontal axis wind turbine (HAWT) and a Darrieus-type vertical axis wind turbine (VAWT) have been designed with CATIA software and constructed using a 3D-printing method. Both wind turbines have undergone series of tests before the voltage and current output from the wind turbines are collected. The result of the test is used to compare the performance of both wind turbines that will imply which design has the best efficiency and performance for Malaysia’s tropical climate. While HAWT can generate higher voltage (up to 8.99 V at one point), it decreases back to 0 V when the wind angle changes. VAWT, however, can generate lower voltage (1.4 V) but changes in the wind angle does not affect its voltage output at all. The analysis has proven that VAWT is significantly more efficient to be built and utilized for Malaysia’s tropical and windy climates. This is also an initiative project to gauge the possibility of building wind turbines, which could be built on the extensive and windy areas surrounding Malaysian airports.  

A Simplified Free Wake Method for Horizontal-Axis Wind Turbine Performance Prediction

1986 ◽  
Vol 108 (4) ◽  
pp. 400-406 ◽  
Author(s):  
A. A. Afjeh ◽  
T. G. Keith
Keyword(s):  
Wind Turbine ◽  
Performance Prediction ◽  
Vortex Method ◽  
Computational Effort ◽  
Horizontal Axis ◽  
Tip Vortex ◽  
Performance Parameters ◽  
Horizontal Axis Wind Turbine ◽  
Turbine Performance ◽  
Free Wake

Based on the assumption that wake geometry of a horizontal-axis wind turbine closely resembles that of a hovering helicopter, a method is presented for predicting the performance of a horizontal-axis wind turbine. A vortex method is used in which the wake is composed of an intense tip-vortex and a diffused inboard wake. Performance parameters are calculated by application of the Biot-Savart law along with the Kutta-Joukowski theorem. Predictions are shown to compare favorably with values from a more complicated full free wake analysis and with existing experimental data, but require more computational effort than an existing fast free wake method.

scholarly journals Experimental investigations of winglet effects on blade geometry of small horizontal axis wind turbine rotors

2021 ◽  
Author(s):  
Manoj Kumar Chaudhary ◽  
◽  
S. Prakash ◽  
Keyword(s):  
Wind Speed ◽  
Wind Turbine ◽  
Lift Coefficient ◽  
Research Work ◽  
Operating Conditions ◽  
Horizontal Axis ◽  
Power Coefficient ◽  
Experimental Investigations ◽  
Horizontal Axis Wind Turbine ◽  
Blade Geometry

In this research work, the investigation and optimization of small horizontal axis wind turbine blade at low wind speed is pursued. The experimental blades were developed using the 3D printing additive manufacturing technique. The airfoils E210, NACA2412, S1223, SG6043, E216, NACA4415, SD7080, SD7033, S1210 and MAF were tested at the wind speed of 2-6 m/s. The airfoils and optimum blade geometry were investigated with the aid of the Xfoil software at Reynolds number of 100,000. The initial investigation range included tip speed ratios from 3 to 10, solidity from 0.0431 – 0.1181 and angle of attacks from 2o to 20o. Later on these parameters were varied in MATLAB and Xfoil software for optimization and investigation of the power coefficient, lift coefficient, drag coefficient and lift to drag ratio. The cut-in wind speed of the rotors was 2 and 2.5 m/s with the winglet-equipped blades and without winglets. It was found that the E210, SG6043, E216 NACA4415 and MAF airfoil displayed better performance than the NACA 2412, S1223, SD7080, S1210 & SD7003 for the geometry optimized for the operating conditions and manufacturing method described.

Sign in / Sign up

Export Citation Format

Share Document