scholarly journals Control of Shrinkage by Loading during Sintering of Water-atomized High-speed-steel Powder Compacts.

1994 ◽  
Vol 41 (9) ◽  
pp. 1134-1138
Author(s):  
Hidenori Kuroki ◽  
Ming Te Wang ◽  
Kim Kwee Wong
Keyword(s):  
High Speed ◽  
High Speed Steel ◽  
Steel Powder ◽  
Powder Compacts

scholarly journals Carbon Control of Sintered SKH51 High Speed Steel Powder Compacts.

1999 ◽  
Vol 46 (11) ◽  
pp. 1185-1189
Author(s):  
Tomita Masakazu ◽  
Ohhara Masaki ◽  
Sugiyama Daigo
Keyword(s):  
High Speed ◽  
High Speed Steel ◽  
Steel Powder ◽  
Powder Compacts ◽  
Carbon Control

scholarly journals Behavior of liquid phase sintering of high speed steel powder compacts.

1986 ◽  
Vol 33 (8) ◽  
pp. 398-401 ◽  
Author(s):  
Shigeaki Takaji ◽  
Minoru Nitta ◽  
Masaki Kawano
Keyword(s):  
Liquid Phase ◽  
High Speed ◽  
High Speed Steel ◽  
Steel Powder ◽  
Liquid Phase Sintering ◽  
Powder Compacts

The Influence of Sintering Atmosphere for Metal Injection Moulding M2 High Speed Steel

2014 ◽  
Vol 879 ◽  
pp. 169-174
Author(s):  
R. Sauti ◽  
N.A. Wahab ◽  
M.A. Omar ◽  
I.N. Ahmad
Keyword(s):  
Mechanical Properties ◽  
Injection Moulding ◽  
High Speed ◽  
High Speed Steel ◽  
Steel Powder ◽  
Sintering Atmosphere ◽  
Temperature Range ◽  
Waste Rubber ◽  
Vacuum Atmosphere ◽  
M2 High Speed Steel

This paper reports on the compatibility of waste rubber as binder for M2 High Speed Steel injection moulding. The feedstock was prepared at a powder loading of 65 vol.% using 22μm M2 High Speed Steel powder and the binders consisting of 55wt.% paraffin wax, 21wt.% polyethylene, 14wt.% waste rubber and 10wt.% stearic acid. The specimens were then sintered in vacuum and 95%N2/5%H2 atmosphere. The sintering in vacuum atmosphere occurred within a temperature range from1200°C to 1260°C, whilst the 95%N2/5%H2 atmosphere was carried out within a temperature range from 1220°C to 1300°C. The effects of the sintering atmosphere and temperature on the physical properties, mechanical properties and microstructure were investigated.

Reduction of R6M5 high-speed steel powder

1987 ◽  
Vol 26 (12) ◽  
pp. 949-952
Author(s):  
V. I. Lyukevich ◽  
Yu. V. Levinskii ◽  
M. V. Fedorovich ◽  
T. A. Maryunina
Keyword(s):  
High Speed ◽  
High Speed Steel ◽  
Steel Powder

Effects of Binders System on Sintered Properties of Metal Injection Molding Parts of M2 High Speed Steel

2014 ◽  
Vol 1024 ◽  
pp. 201-204 ◽  
Author(s):  
Rosliza Sauti ◽  
Nor‘aini Wahab ◽  
Mohd Afian Omar ◽  
I.N. Ahmad
Keyword(s):  
Injection Molding ◽  
High Speed ◽  
High Speed Steel ◽  
Palm Stearin ◽  
Steel Powder ◽  
Paraffin Wax ◽  
Metal Injection Molding ◽  
Waste Rubber ◽  
Vacuum Atmosphere ◽  
M2 High Speed Steel

This paper reports on the compatibility of waste rubber binder combined with conventional binder, paraffin wax and local binder, palm stearin for M2 High Speed Steel injection molding in order to obtain the better properties. The feedstock was prepared at a powder loading of 65 vol.% using 22um M2 High Speed Steel powder and the binders consisting of 55wt.% paraffin wax/palm stearin, 21wt.% polyethylene, 14wt.% waste rubber and 10wt.% stearic acid. The specimens were then sintered in vacuum atmosphere within a temperature range from 1200°C to 1260°C. The results shown even the best properties is obtain from the conventional binders, paraffin wax, thus the properties of local binders palm stearin is still comparable and good. The maximum density of paraffin wax binder was 8.095g/cm3 achieved at temperature 1250°C and palm stearin binder was 8.111g/cm3 achieved at temperature 1240°C. Therefore, in term the best strength of paraffin wax was 2351Mpa whilst palm stearin was 2210MPa, both recorded at temperature 1230°C.

A thermal analysis study on nitriding R6M5 high-speed steel powder

1995 ◽  
Vol 34 (5-6) ◽  
pp. 244-246
Author(s):  
O. A. Mazno ◽  
I. R. Dolgoarshinnykh ◽  
A. A. Yudakov
Keyword(s):  
Thermal Analysis ◽  
High Speed ◽  
High Speed Steel ◽  
Steel Powder ◽  
Analysis Study ◽  
Thermal Analysis Study
Sign in / Sign up

Export Citation Format

Share Document