Thermal-mechanical response of nearly opaque materials exposed to continuous radiation

AIAA Journal ◽  
1971 ◽  
Vol 9 (10) ◽  
pp. 1911-1920 ◽  
Author(s):  
JOHN T. HOWE
Keyword(s):  
Mechanical Response ◽  
Continuous Radiation

Variation of the amount of hydrogen along the galactic ridge

1967 ◽  
Vol 31 ◽  
pp. 171-172
Author(s):  
Th. Schmidt-Kaler
Keyword(s):  
Surface Brightness ◽  
Milky Way ◽  
Neutral Hydrogen ◽  
Line Of Sight ◽  
Optical Surface ◽  
Hydrogen Density ◽  
Continuous Radiation ◽  
Galactic Longitude

The integralNHof neutral-hydrogen density along the line of sight is determined from the Kootwijk and Sydney surveys. The run ofNHwith galactic longitude agrees well with that of thermal continuous radiation and that of the optical surface brightness of the Milky Way.

Comparison of Substructures Between Uniaxial and Biaxial Deformation in 1100-0 Aluminum

1981 ◽  
Vol 39 ◽  
pp. 52-53
Author(s):  
D. L. Rohr ◽  
S. S. Hecker
Keyword(s):  
Plastic Strain ◽  
Cell Walls ◽  
Room Temperature ◽  
Mechanical Response ◽  
Biaxial Tension ◽  
Initial Deformation ◽  
Uniaxial Deformation ◽  
Biaxial Deformation ◽  
Stress States ◽  
Comprehensive Study

As part of a comprehensive study of microstructural and mechanical response of metals to uniaxial and biaxial deformations, the development of substructure in 1100 A1 has been studied over a range of plastic strain for two stress states.Specimens of 1100 aluminum annealed at 350 C were tested in uniaxial (UT) and balanced biaxial tension (BBT) at room temperature to different strain levels. The biaxial specimens were produced by the in-plane punch stretching technique. Areas of known strain levels were prepared for TEM by lapping followed by jet electropolishing. All specimens were examined in a JEOL 200B run at 150 and 200 kV within 24 to 36 hours after testing.The development of the substructure with deformation is shown in Fig. 1 for both stress states. Initial deformation produces dislocation tangles, which form cell walls by 10% uniaxial deformation, and start to recover to form subgrains by 25%. The results of several hundred measurements of cell/subgrain sizes by a linear intercept technique are presented in Table I.

Construction of plastic contact deformation maps on ceramics: a case study on aluminum nitride

1996 ◽  
Vol 54 ◽  
pp. 636-637
Author(s):  
D. L. Callahan
Keyword(s):  
Plastic Deformation ◽  
Aluminum Nitride ◽  
Mechanical Response ◽  
Three Dimensional ◽  
Bright Field Image ◽  
Perfectly Plastic ◽  
Contrast Analysis ◽  
Deformation Patterns

Modern polishing, precision machining and microindentation techniques allow the processing and mechanical characterization of ceramics at nanometric scales and within entirely plastic deformation regimes. The mechanical response of most ceramics to such highly constrained contact is not predictable from macroscopic properties and the microstructural deformation patterns have proven difficult to characterize by the application of any individual technique. In this study, TEM techniques of contrast analysis and CBED are combined with stereographic analysis to construct a three-dimensional microstructure deformation map of the surface of a perfectly plastic microindentation on macroscopically brittle aluminum nitride.The bright field image in Figure 1 shows a lg Vickers microindentation contained within a single AlN grain far from any boundaries. High densities of dislocations are evident, particularly near facet edges but are not individually resolvable. The prominent bend contours also indicate the severity of plastic deformation. Figure 2 is a selected area diffraction pattern covering the entire indentation area.

Nanosecond laser-induced breakdown assisted by femtosecond laser pre-ionization in air: the effect on spatial resolution and continuous radiation

2020 ◽  
Vol 92 (2) ◽  
pp. 20701
Author(s):  
Bo Li ◽  
Xiaofeng Li ◽  
Zhifeng Zhu ◽  
Qiang Gao
Keyword(s):  
Femtosecond Laser ◽  
Spatial Resolution ◽  
Laser Induced Breakdown Spectroscopy ◽  
Nanosecond Laser ◽  
Breakdown Threshold ◽  
Powerful Technique ◽  
Breakdown Spectroscopy ◽  
Continuous Radiation ◽  
Laser Induced Breakdown

Laser-induced breakdown spectroscopy (LIBS) is a powerful technique for quantitative diagnostics of gases. The spatial resolution of LIBS, however, is limited by the volume of plasma. Here femtosecond-nanosecond dual-pulsed LIBS was demonstrated. Using this method, the breakdown threshold was reduced by 80%, and decay of continuous radiation was shortened. In addition, the volume of the plasma was shrunk by 85% and hence, the spatial resolution of LIBS was significantly improved.

Determination of the profile of the temperature field of material heated by continuous laser radiation

2020 ◽  
pp. 51-10
Author(s):  
B.A. Lapshinov ◽  
◽  
N.I. Timchenko ◽  
Keyword(s):  
Temperature Field ◽  
Optical Fiber ◽  
Prolonged Exposure ◽  
Radiation Spectrum ◽  
Visible Range ◽  
Continuous Laser ◽  
Surface Temperature Distribution ◽  
Continuous Radiation ◽  
Spectral Pyrometry

Spectral pyrometry was used to determine the surface temperature distribution of Si, Nb, Cu, and graphite samples when they were locally heated by continuous radiation of an Nd:YAG laser (λ = 1.064 μm). With prolonged exposure to radiation, a stationary temperature field was established in the samples. The thermal spectra were recorded with a small spectrometer in the visible range in the temperature range above 850 K. The optical fiber used to transmit the radiation spectrum to the spectrometer had an additional diaphragm with a diameter of 1 mm located at a certain distance from the fiber end, which ensured the locality of the recorded spectra. The optical fiber moved continuously along the sample, and the spectrometer recorded up to 100 spectra with a frequency of 5-10 Hz. The temperature profile of the samples was calculated based on the results of processing the spectra using the Spectral Pyrometry program.

Sign in / Sign up

Export Citation Format

Share Document