A STEP BY STEP PROCEDURE TO PERFORM ISOGEOMETRIC ANALYSIS OF BEAM AND BAR PROBLEMS IN CIVIL ENGINEERING INCLUDING SIZING OPTIMISATION OF A BEAM

2018 ◽  
Vol 7 (1) ◽  
pp. 13
Author(s):  
K.N.V. CHANDRASEKHAR ◽  
N.S.S. SAHITHI ◽  
◽  
Keyword(s):  
Isogeometric Analysis ◽  
Civil Engineering ◽  
Step Procedure

Scanning Tunneling Microscopy of Amorphous Carbon Films

1990 ◽  
Vol 48 (1) ◽  
pp. 318-319
Author(s):  
Mircea Fotino ◽  
D.C. Parks
Keyword(s):  
Scanning Tunneling Microscopy ◽  
Amorphous Carbon ◽  
Carbon Films ◽  
Atomic Scale ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
Amorphous Carbon Films ◽  
Image Optimization ◽  
Step Procedure ◽  
Stm Images

In the last few years scanning tunneling microscopy (STM) has made it possible and easily accessible to visualize surfaces of conducting specimens at the atomic scale. Such performance allows the detailed characterization of surface morphology in an increasing spectrum of applications in a wide variety of fields. Because the basic imaging process in STM differs fundamentally from its equivalent in other well-established microscopies, good understanding of the imaging mechanism in STM enables one to grasp the correct information content in STM images. It thus appears appropriate to explore by STM the structure of amorphous carbon films because they are used in many applications, in particular in the investigation of delicate biological specimens that may be altered through the preparation procedures.All STM images in the present study were obtained with the commercial instrument Nanoscope II (Digital Instruments, Inc., Santa Barbara, California). Since the importance of the scanning tip for image optimization and artifact reduction cannot be sufficiently emphasized, as stressed by early analyses of STM image formation, great attention has been directed toward adopting the most satisfactory tip geometry. The tips used here consisted either of mechanically sheared Pt/Ir wire (90:10, 0.010" diameter) or of etched W wire (0.030" diameter). The latter were eventually preferred after a two-step procedure for etching in NaOH was found to produce routinely tips with one or more short whiskers that are essentially rigid, uniform and sharp (Fig. 1) . Under these circumstances, atomic-resolution images of cleaved highly-ordered pyro-lytic graphite (HOPG) were reproducibly and readily attained as a standard criterion for easily recognizable and satisfactory performance (Fig. 2).

Procedure for Maximizing Phonological Information from Single-Word Responses

1984 ◽  
Vol 15 (4) ◽  
pp. 267-274 ◽  
Author(s):  
Harriet B. Klein
Keyword(s):  
Phonological Information ◽  
Single Word ◽  
Preliminary Assessment ◽  
Target Attainment ◽  
Phonological Processes ◽  
Step Procedure ◽  
Yield Information ◽  
Assessment Measure ◽  
Busy Clinician ◽  
Planning Intervention

Formal articulation test responses are often used by the busy clinician as a basis for planning intervention goals. This article describes a 6-step procedure for using efficiently the single-word responses elicited with an articulation test. This procedure involves the assessment of all consonants within a word rather than only test-target consonants. Responses are organized within a Model and Replica chart to yield information about an individual's (a) articulation ability, (b) frequency of target attainment, substitutions, and deletions, (c) variability in production, and (d) phonological processes. This procedure is recommended as a preliminary assessment measure. It is advised that more detailed analysis of continuous speech be undertaken in conjunction with early treatment sessions.

Sex Crimes and Civil Engineering

1993 ◽  
Vol 38 (5) ◽  
pp. 499-500
Author(s):  
Harvey A. Hornstein
Keyword(s):  
Civil Engineering ◽  
Sex Crimes

Civil Engineering Notes

1922 ◽  
Vol 126 (3) ◽  
pp. 213-213
Keyword(s):  
Civil Engineering

Civil Engineering Notes

1922 ◽  
Vol 127 (2) ◽  
pp. 134-134
Keyword(s):  
Civil Engineering

Plasminogen-Activator in Human Early Milk: Its Partial Purification and Characterization

1981 ◽  
Vol 45 (02) ◽  
pp. 121-126 ◽  
Author(s):  
Utako Okamoto ◽  
Noboru Horie ◽  
Yoko Nagamatsu ◽  
Jun-Ichiro Yamamoto
Keyword(s):  
Plasminogen Activator ◽  
Polyacrylamide Gel Electrophoresis ◽  
Gel Filtration ◽  
Partial Purification ◽  
Order Kinetic ◽  
Diisopropyl Fluorophosphate ◽  
Step Procedure ◽  
Activity Band ◽  
C 50 ◽  
Gel Isoelectric Focusing

SummaryMilk plasminogen-activator was partially purified from human transitional milk collected at about 10 days after delivery, by a five-step procedure involving chloroform treatment, ammonium sulfate precipitation, and column chromatography on Sephadex G-150, CM Sephadex C-50 and DEAE Sephadex A-50. This gave milk-activator with a maximum purification factor of about 2,400-fold with respect to the skimmed milk. The CM Sephadex-step preparation showed, on polyacrylamide gel electrophoresis, a single plasminogen-activator activity band located between the bands of albumin and prealbumin of human serum. This preparation exhibited no kinin forming activity. The activator hydrolyzed acetyl-glycyl-L-lysine methyl ester with similar order kinetic constants to urokinase, and was inhibited strongly by diisopropyl-fluorophosphate. The molecular weight of the activator as estimated by gel filtration was approximately 86,000, the isoelectric points as estimated by gel isoelectric focusing were pH 7.2, 6.9 and 6.6, and the activator activity was not quenched by antiurokinase globulin, indicating that the milk-activator is a different entity from urokinase.

Sign in / Sign up

Export Citation Format

Share Document