scholarly journals A framework for measuring the time-varying shape and full-field deformation of residual limbs using 3D digital image correlation

2019 ◽  
Author(s):  
Dana Solav ◽  
Kevin Mattheus Moerman ◽  
Aaron M. Jaeger ◽  
Hugh M. Herr
Keyword(s):  
High Resolution ◽  
Digital Image Correlation ◽  
Digital Image ◽  
Soft Tissues ◽  
Low Cost ◽  
Image Correlation ◽  
Time Varying ◽  
Residual Limb ◽  
Full Field ◽  
Prosthetic Socket

Effective prosthetic socket design following lower-limb amputation depends upon the accurate characterization of the shape of the residual limb as well as its volume and shape fluctuations. Objective: This study proposes a novel framework for the measurement and analysis of residual limb shape and deformation, using a high-resolution and low-cost system. Methods: A multi-camera system was designed to capture sets of simultaneous images of the entire residuum surface. The images were analyzed using a specially developed open-source three-dimensional digital image correlation (3D-DIC) toolbox, to obtain the accurate time-varying shapes as well as the full-field deformation and strain maps on the residuum skin surface. Measurements on a transtibial amputee residuum were obtained during knee flexions, muscle contractions, and swelling upon socket removal. Results: It was demonstrated that 3D-DIC can be employed to quantify with high resolution the time-varying residuum shapes, deformations, and strains. Additionally, the enclosed volumes and cross-sectional areas were computed and analyzed. Conclusion: This novel low-cost framework provides a promising solution for the in-vivo evaluation of residuum shapes and strains, as well as the potential for characterizing the mechanical properties of the underlying soft-tissues. Significance: These data may be used to inform data-driven computational algorithms for the design of prosthetic sockets, as well as of other wearable technologies mechanically interfacing with the skin.

Digital Image Correlation for Full-Field High Resolution Assessment of Leaf Growth

2015 ◽  
Vol 34 (2) ◽  
pp. 433-439 ◽  
Author(s):  
Adriaan Campo ◽  
Przemyslaw Klosiewicz ◽  
Joris Dirckx
Keyword(s):  
High Resolution ◽  
Digital Image Correlation ◽  
Digital Image ◽  
Leaf Growth ◽  
Image Correlation ◽  
Full Field

scholarly journals Evaluation of a low-cost approach to 2-D digital image correlation vs. a commercial stereo-DIC system in Brazilian testing of soil specimens

2021 ◽  
Vol 22 (1) ◽  
Author(s):  
M. Arza-García ◽  
C. Núñez-Temes ◽  
J. A. Lorenzana ◽  
J. Ortiz-Sanz ◽  
A. Castro ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Accuracy Assessment ◽  
Low Cost ◽  
Field Measurements ◽  
Image Correlation ◽  
Strain Gauges ◽  
Source Image ◽  
Full Field ◽  
Cost Approach

AbstractDue to their cost, high-end commercial 3D-DIC (digital image correlation) systems are still inaccessible for many laboratories or small factories interested in lab testing materials. These professional systems can provide reliable and rapid full-field measurements that are essential in some laboratory tests with high-strain rate events or high dynamic loading. However, in many stress-controlled experiments, such as the Brazilian tensile strength (BTS) test of compacted soils, samples are usually large and fail within a timeframe of several minutes. In those cases, alternative low-cost methods could be successfully used instead of commercial systems. This paper proposes a methodology to apply 2D-DIC techniques using consumer-grade cameras and the open-source image processing software DICe (Sandia National Lab) for monitoring the standardized BTS test. Unlike most previous studies that theoretically estimate systematic errors or use local measures from strain gauges for accuracy assessment, we propose a contrast methodology with independent full-field measures. The displacement fields obtained with the low-cost system are benchmarked with the professional stereo-DIC system Aramis-3D (GOM GmbH) in four BTS experiments using compacted soil specimens. Both approaches proved to be valid tools for obtaining full-field measurements and showing the sequence of crack initiation, propagation and termination in the BTS, constituting reliable alternatives to traditional strain gauges. Mean deviations obtained between the low-cost 2D-DIC approach and Aramis-3D in measuring in-plane components were 0.08 mm in the perpendicular direction of loading (ΔX) and 0.06 mm in the loading direction (ΔY). The proposed low-cost approach implies considerable savings compared to commercial systems.

Speckle Pattern Characterisation for High Resolution Digital Image Correlation

2011 ◽  
Vol 70 ◽  
pp. 261-266 ◽  
Author(s):  
G. Crammond ◽  
S.W. Boyd ◽  
Janice M. Dulieu-Barton
Keyword(s):  
High Resolution ◽  
Digital Image Correlation ◽  
Spatial Resolution ◽  
Digital Image ◽  
Speckle Pattern ◽  
Correlation Method ◽  
Image Correlation ◽  
Optical Technique ◽  
Full Field ◽  
Grey Scale

Digital image correlation (DIC) is an optical technique for full field deformation measurement. The spatial resolution and precision of the measurements are limited by the number of pixels within the image. The use of magnifying optics provides greater spatial resolution images, enabling smaller displacements to be observed with greater accuracy. Increasing the magnification of an image significantly changes the appearance of the non-periodic, stochastic speckle pattern which provides the grey scale contrast necessary for the image correlation method. In the paper a methodology is developed to evaluate the properties of different speckle pattern types under a range of resolutions up to 705 pixel / mm. Numerical deformation of the patterns is also undertaken to evaluate how the changes in the pattern properties affect the accuracy of the DIC measurements.

scholarly journals RGB Colour Encoding Improvement for Three-Dimensional Shapes and Displacement Measurement Using the Integration of Fringe Projection and Digital Image Correlation

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 3130 ◽  
Author(s):  
Luis Felipe-Sesé ◽  
Ángel Molina-Viedma ◽  
Elías López-Alba ◽  
Francisco Díaz
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
High Speed ◽  
Low Cost ◽  
Three Dimensional ◽  
Displacement Measurement ◽  
Image Correlation ◽  
Fringe Projection ◽  
Colour Pattern ◽  
Full Field

Three-dimensional digital image correlation (3D-DIC) has become the most popular full-field optical technique for measuring 3D shapes and displacements in experimental mechanics. The integration of fringe projection (FP) and two-dimensional digital image correlation (FP + DIC) has been recently established as an intelligent low-cost alternative to 3D-DIC, overcoming the drawbacks of a stereoscopic system. Its experimentation is based on the colour encoding of the characterized fringe and speckle patterns required for FP and DIC implementation, respectively. In the present work, innovations in experimentation using FP + DIC for more accurate results are presented. Specifically, they are based on the improvement of the colour pattern encoding. To achieve this, in this work, a multisensor camera and/or laser structural illumination were employed. Both alternatives are analysed and evaluated. Results show that improvements both in three-dimensional and in-plane displacement are obtained with the proposed alternatives. Nonetheless, multisensor high-speed cameras are uncommon, and laser structural illumination is established as an important improvement when low uncertainty is required for 2D-displacement measurement. Hence, the uncertainty has been demonstrated to be reduced by up to 50% compared with results obtained in previous experimental approaches of FP + DIC.

scholarly journals Experimental Characterization of the FRCM-Concrete Interface Bond Behavior Assisted by Digital Image Correlation

Sensors ◽  
2021 ◽  
Vol 21 (4) ◽  
pp. 1154
Author(s):  
Dario De Domenico ◽  
Antonino Quattrocchi ◽  
Damiano Alizzio ◽  
Roberto Montanini ◽  
Santi Urso ◽  
...  
Keyword(s):  
Digital Image Correlation ◽  
Digital Image ◽  
Mechanical Tests ◽  
Image Correlation ◽  
Front Face ◽  
Full Field ◽  
Bond Behavior ◽  
Externally Bonded ◽  
Strengthening Technique ◽  
Concrete Interface

Digital Image Correlation (DIC) provides measurements without disturbing the specimen, which is a major advantage over contact methods. Additionally, DIC techniques provide full-field maps of response quantities like strains and displacements, unlike traditional methods that are limited to a local investigation. In this work, an experimental application of DIC is presented to investigate a problem of relevant interest in the civil engineering field, namely the interface behavior between externally bonded fabric reinforced cementitious mortar (FRCM) sheets and concrete substrate. This represents a widespread strengthening technique of existing reinforced concrete structures, but its effectiveness is strongly related to the bond behavior between composite fabric and underlying concrete. To investigate this phenomenon, a set of notched concrete beams are realized, reinforced with FRCM sheets on the bottom face, subsequently cured in different environmental conditions (humidity and temperature) and finally tested up to failure under three-point bending. Mechanical tests are carried out vis-à-vis DIC measurements using two distinct cameras simultaneously, one focused on the concrete front face and another focused on the FRCM-concrete interface. This experimental setup makes it possible to interpret the mechanical behavior and failure mode of the specimens not only from a traditional macroscopic viewpoint but also under a local perspective concerning the evolution of the strain distribution at the FRCM-concrete interface obtained by DIC in the pre- and postcracking phase.

scholarly journals Super Resolution Digital Image Correlation (SR-DIC): an Alternative to Image Stitching at High Magnifications

2021 ◽  
Author(s):  
R. S. Hansen ◽  
D. W. Waldram ◽  
T. Q. Thai ◽  
R. B. Berke
Keyword(s):  
High Resolution ◽  
Digital Image Correlation ◽  
Spatial Resolution ◽  
Digital Image ◽  
Super Resolution ◽  
Image Correlation ◽  
Low Resolution ◽  
Strain Measurements ◽  
Resolution Image ◽  
High Resolution Image

Abstract Background High-resolution Digital Image Correlation (DIC) measurements have previously been produced by stitching of neighboring images, which often requires short working distances. Separately, the image processing community has developed super resolution (SR) imaging techniques, which improve resolution by combining multiple overlapping images. Objective This work investigates the novel pairing of super resolution with digital image correlation, as an alternative method to produce high-resolution full-field strain measurements. Methods First, an image reconstruction test is performed, comparing the ability of three previously published SR algorithms to replicate a high-resolution image. Second, an applied translation is compared against DIC measurement using both low- and super-resolution images. Third, a ring sample is mechanically deformed and DIC strain measurements from low- and super-resolution images are compared. Results SR measurements show improvements compared to low-resolution images, although they do not perfectly replicate the high-resolution image. SR-DIC demonstrates reduced error and improved confidence in measuring rigid body translation when compared to low resolution alternatives, and it also shows improvement in spatial resolution for strain measurements of ring deformation. Conclusions Super resolution imaging can be effectively paired with Digital Image Correlation, offering improved spatial resolution, reduced error, and increased measurement confidence.

The Stress Intensity Factor of Opening Mode Determined by Digital Image Correlation

2011 ◽  
Vol 83 ◽  
pp. 54-59 ◽  
Author(s):  
Rui Zhang ◽  
Ling Feng He ◽  
Chang Rong Li
Keyword(s):  
Stress Intensity Factor ◽  
Stress Intensity ◽  
Digital Image Correlation ◽  
Intensity Factor ◽  
Digital Image ◽  
Correlation Method ◽  
Compact Tension ◽  
Image Correlation ◽  
Full Field ◽  
Opening Mode

Applications of the digital image correlation method (DIC) for the determination of the opening mode stress intensity factor (SIF) is investigated using an edge cracked aluminum plate in this paper. Standard compact tension test specimen was tested under tensile loading and the full-field displacement fields of the test sample were recorded using DIC. The SIF associated with unavoidable rigid-body displacement translation were calculated simultaneously from the experimental data by fitting the theoretical displacement field using the method of least-squares. Selection of displacement and convergence values is discussed. For validation, the SIF thus determined is compared with theoretical results, confirming the effectiveness and accuracy of the proposed technique. Therefore it reveals that the DIC is a practical and effective tool for full-field deformation and SIF measurement.

Sign in / Sign up

Export Citation Format

Share Document