scholarly journals Effect of Hammer Shape on Energy Transfer Measurement in the Standard Penetration Test

2004 ◽  
Vol 44 (3) ◽  
pp. 103-114 ◽  
Author(s):  
Jiin-Song Tsai ◽  
Yean-Jhe Liou ◽  
Fu-Chen Liu ◽  
Chin-Huei Chen
Keyword(s):  
Energy Transfer ◽  
Standard Penetration Test ◽  
Penetration Test ◽  
Transfer Measurement

Becker and standard penetration tests (BPT–SPT) correlations with consideration of casing friction

1994 ◽  
Vol 31 (3) ◽  
pp. 343-356 ◽  
Author(s):  
Alex Sy ◽  
R.G. (Dick) Campanella
Keyword(s):  
British Columbia ◽  
Energy Transfer ◽  
Stress Wave ◽  
Standard Penetration Test ◽  
Energy Output ◽  
Rational Approach ◽  
Stress Wave Propagation ◽  
Penetration Test ◽  
In Situ Tests ◽  
Foundation Design

The Becker penetration test (BPT), through correlations with the standard penetration test (SPT), is widely used for foundation design and liquefaction assessment in gravelly soils. Most of the existing correlations, however, do not adequately account for the variable energy output of the diesel hammer used in the Becker system, and shaft friction on the Becker casing is ignored. An alternative and more rational approach to BPT–SPT correlations is presented, based on experimental and numerical studies conducted at the University of British Columbia. The research involves performing SPT, BPT, and other in situ tests at several sites in British Columbia and includes dynamic measurements of energy transfer in the SPT and BPT. Stress-wave measurements and wave-equation analyses are used to evaluate the effect of friction on the BPT blow count. New BPT–SPT correlations are proposed that consider the energy transfer in both tests and explicitly consider casing friction in the BPT. A recommended procedure for estimating equivalent SPT N60 from BPT blow count is presented. Key words : Becker penetration test, standard penetration test, dynamic measurement, pile driving, stress-wave propagation.

Standard penetration test energy measurements using a system based on the personal computer

1992 ◽  
Vol 29 (4) ◽  
pp. 551-557 ◽  
Author(s):  
Peter K. Robertson ◽  
David J. Woeller ◽  
Kofi O. Addo
Keyword(s):  
Energy Transfer ◽  
Test Procedure ◽  
Standard Penetration Test ◽  
Energy Calibration ◽  
Calibration System ◽  
Penetration Test ◽  
Reference Test ◽  
Time Record ◽  
Force Time

According to the International Reference Test procedure for the standard penetration test (SPT), in situations where comparisons of SPT results are important, calibrations should be made to evaluate the efficiency of the equipment in terms of energy transfer. However, equipment to measure the energy transfer of the hammer anvil system is not commonly available. Ten years ago a system was developed and made commercially available. However, this system is no longer available. An SPT energy calibration system is described that has been developed based on a microcomputer. The load cell to measure the compressive stress wave beneath the SPT anvil consists of a 0.5-m length of strain-gauged AW rod. Specialized software has been developed to record the force–time record for each hammer blow on a portable microcomputer. Examples of energy measurements are presented and discussed. Key words : standard penetration test, in situ, microcomputer, energy.

Comportement de pieux d'essais instrumentés sous charge horizontale

1993 ◽  
Vol 30 (1) ◽  
pp. 1-11
Author(s):  
R. Frank ◽  
H. Zervogiannis ◽  
S. Christoulas ◽  
V. Papadopoulos ◽  
N. Kalteziotis
Keyword(s):  
Pile Foundation ◽  
Bending Moment ◽  
Standard Penetration Test ◽  
American Petroleum Institute ◽  
Full Scale ◽  
Test Method ◽  
Cohesionless Soil ◽  
Penetration Test ◽  
Cohesionless Soils ◽  
Final Design

This paper describes the behaviour of two test piles (one bored and postgrouted and one simply bored, both 31.7 m long and 0.75 m in diameter) subjected to horizontal loads. These full-scale pile tests were carried out for the actual design of the pile foundation of a pier of the Evripos cable-stayed bridge. This bridge will link the Euboea Island to mainland Greece. The two piles have already been subjected to bearing capacity tests under axial loadings. The inclinometer measurements, taken during the present tests, yielded, in particular, the deformed shape of the piles as well as the bending moments. Conclusions could be drawn for the final design of the pile foundation with respect to horizontal loadings. Furthermore, various calculation methods using p–y reaction curves for cohesionless soils have been checked: the Ménard pressuremeter method, the method of the American Petroleum Institute recommendations, and the Standard penetration test method of Christoulas. These pile tests show that simple measurements, taken on construction sites, can yield interesting results on the actual behaviour of horizontally loaded piles. Key words : pile, horizontal loading, full-scale test, horizontal loads, bending moment, subgrade reaction modulus, p–y curve, cohesionless soil, Standard penetration test, pressuremeter test.

Assessment of the range of variation of Nγ from 60 estimation methods for footings on sand

2013 ◽  
Vol 50 (7) ◽  
pp. 793-800 ◽  
Author(s):  
Edgar Giovanny Diaz-Segura
Keyword(s):  
Friction Angle ◽  
Standard Penetration Test ◽  
Estimation Methods ◽  
Penetration Test ◽  
In Situ Tests ◽  
Vertical Loading ◽  
Simplified Method ◽  
Bearing Capacity Factor ◽  
Range Of Variation

The range of variation of the bearing capacity factor, Nγ, was assessed using 60 estimation methods for rough footings on sand subjected to static vertical loading. The influence on the Nγ values of the use of correlations for the estimation of the friction angle, [Formula: see text], derived from in situ tests was also assessed. The analysis shows a marked dependency on the methods used to determine Nγ, showing differences for the same [Formula: see text] values of up to 267% between estimated values. Uncertainty in the estimation of [Formula: see text], due to the use of correlations with in situ tests, leads to a range of variation for Nγ higher than that seen using the 60 estimation methods. Finally, given the regular use of the in situ standard penetration test (SPT) on sands, and based on a series of analyses using finite elements, a simplified method in terms of the SPT N-values is proposed for estimation of Nγ in footings on sands.

Sign in / Sign up

Export Citation Format

Share Document