scholarly journals Investigation of Acoustic Properties of Different Types of Low-Noise Road Surfacers under In Situ and Laboratory Conditions

Materials ◽  
2022 ◽  
Vol 15 (2) ◽  
pp. 480
Author(s):  
Janusz Bohatkiewicz ◽  
Maciej Hałucha ◽  
Marcin Kamil Dębiński ◽  
Michał Jukowski ◽  
Zbigniew Tabor
Keyword(s):  
Sound Absorption ◽  
Low Noise ◽  
Operating Conditions ◽  
Acoustic Properties ◽  
Road Noise ◽  
In Situ Conditions ◽  
Study Results ◽  
Road Surfaces ◽  
Impedance Tube Method

Current literature on the performance characteristics of road surfaces is primarily focused on evenness, roughness and technical durability. However, other important surface properties require analysis, including noisiness, which is an important feature of the environmental impact of vehicular traffic around roads. This can be studied using various methods by which road noise phenomena are investigated. The method used to measure the noise performance of road surfaces herein is the Statistical Pass-By (SPB) method, as described in ISO 11819-1:1997. The impedance tube method was used for sound absorption testing, as described in ISO 13472-2:2010. These tests were performed under a variety of conditions: in situ and in laboratory. The existence of relationships between them can be helpful in selecting surfaces for noise reduction. Preliminary surface noise tests can be performed in the laboratory with samples consisting of various compounds. This is less expensive and faster than doing so on purpose-built surfaces. The paper presents study results for sound absorption coefficients of various types of low-noise surfaces in in situ conditions (on an experimental section and on operated road sections) and in the laboratory setting. The results of the tests performed on the operational sections were compared to the results of the surface impact on road noise using the SPB method. The correlations between the test results help confirm the feasibility of road surface pre-testing in the laboratory and the relation to tests performed using the SPB method under typical operating conditions.

Trial applications at gymnasiums of in-situ sound absorption measurement method by ensemble averaging technique

2021 ◽  
Vol 263 (2) ◽  
pp. 4532-4537
Author(s):  
Toru Otsuru ◽  
Reiji Tomiku ◽  
Noriko Okamoto ◽  
Siwat Lawanwadeekul
Keyword(s):  
Measurement Method ◽  
Sound Absorption ◽  
Glass Wool ◽  
Absorption Measurement ◽  
Ensemble Averaging ◽  
Averaging Technique ◽  
In Situ Conditions ◽  
Measurement Consistency ◽  
Absorption Characteristics

The authors have been published a series of papers on a measurement method for sound absorption characteristics of materials using ensemble averaging technique, i.e., EA method. The papers' results included measurement mechanisms, measurement uncertainty, and so on. Herein, to examine adaptability, especially in in-situ conditions, the EA method is applied to measure absorption characteristics of materials installed in two gymnasiums. A glass-wool panel with the dimension of 0.5 m by 0.5 m by 0.05 m and with the density of 32 kg m^-3 was brought around and measured to check the measurement consistency. Several measurements were conducted during badminton plays were undergoing. Measured sound absorption coefficients revealed that most results agree well with those measured in reverberation rooms. Certain improvement is necessary for the specimen brought to the in-situ measurement to keep the consistency. The inconsistency is considered to originate from unstable conditions between the specimen and floor.

scholarly journals Acoustic Properties of Mixing Empty Fruit Bunch and Oil Palm Frond Natural Fibres

2019 ◽  
Vol 8 (4) ◽  
pp. 6347-6349
Keyword(s):  
Oil Palm ◽  
Sound Absorption ◽  
Natural Fibre ◽  
Natural Fibres ◽  
Acoustic Properties ◽  
Empty Fruit Bunch ◽  
Frequency Range ◽  
Oil Palm Frond ◽  
Impedance Tube Method ◽  
Palm Frond

Natural fibre is being studied and used as sound absorber for its promising acoustic properties. For instance, Germany have commercial plants that are producing sound absorbers from natural fibre. Natural fibre is eco-friendly and has no effect on human health. Besides that, the production cost of natural fibre is cheaper than synthetic fibre. This research reported the thickness effects on acoustic properties in different ratios of natural fibres of empty fruit bunch (EFB) and oil palm frond (OPF). Four different thickness of low density fibre board (LDF) have been fabricated (12 mm, 14 mm, 16 mm and 18 mm) in density of 120 kg/m3 . The Sound Absorption Coefficient (SAC) was tested by using the Impedance Tube Method (ITM) according to ASTM E1050-98 standards at frequency from 0 Hz to 6400 Hz. The results show the values of SAC for all samples increase with increasing in thickness from frequency range of 0 Hz – 4500 Hz. It is noteworthy that the LDF with thickness of 16 mm and 18 mm can be classified as Class A sound absorbing material according to sound absorption classes and possess the SAC values of 0.8 and above at a wider frequency range, which is 2500 Hz to 6400 Hz. The combination of EFP and OPF natural fibres has a very promising and excellent performance in acoustic properties.

scholarly journals Identification of uncertainty levels of acoustic properties of biocomposites under different mounting conditions in impedance tube tests

2021 ◽  
Vol 69 (5) ◽  
pp. 392-400
Author(s):  
Hasan Koruk ◽  
Yusuf Saygili ◽  
Garip Genc ◽  
Kenan Y. Sanliturk
Keyword(s):  
Sound Absorption ◽  
Transmission Loss ◽  
Acoustic Properties ◽  
Petroleum Jelly ◽  
Impedance Tube ◽  
Hard Materials ◽  
Inner Diameter ◽  
Acoustic Properties Of Materials ◽  
Impedance Tube Method ◽  
Textured Materials

Impedance tube method is widely used to measure acoustic properties of materials. Although this method yields reliable acoustic properties for soft textured materials, uncertainty levels of measured acoustic properties for hard materials, including biocomposites, can be quite large, mainly due to uncertain mounting conditions. Here, the effects of mounting conditions on the acoustic properties of biocomposites in an impedance tube are investigated. First, nominally identical biocomposite samples with a diameter equal to the inner diameter of impedance tube are manufactured and their acoustic properties are determined. As hard materials practically cause fitting problems in the impedance tube, the diameters of samples are reduced, as in practice, by small amounts and acoustic properties of modified samples are determined. Furthermore, in order to match the diameters of samples to the inner diameter of impedance tube, different materials such as tape, petroleum jelly and cotton are applied around samples to close the air gap between the samples and the tube's inner wall. All the results are compared, and the uncertainty levels caused by different mounting conditions on the acoustic properties of biocomposites are identified. The results show that the transmission loss (TL) measurements are dramatically affected by the mounting conditions while the sound absorption conditions are less sensitive to the mounting conditions. The deviations in the measured TL levels are highest for the samples with tape and wax (10–15 dB). On the other hand, the deviations in the measured sound absorption coefficients are highest for the samples with cotton and tape (1–2%).

scholarly journals Investigation of the Sound Absorption and Transmission Loss Performances of Green Homogenous and Hybrid Luffa and Jute Fiber Samples

2021 ◽  
Author(s):  
Ahmet C. Ozcan ◽  
Kenan Y. Sanliturk ◽  
Garip Genc ◽  
Hasan Koruk
Keyword(s):  
High Frequency ◽  
Sound Absorption ◽  
Transmission Loss ◽  
Natural Fibers ◽  
Acoustic Properties ◽  
Jute Fiber ◽  
Transmission Losses ◽  
Hybrid Fiber ◽  
Practical Applications ◽  
Impedance Tube Method

In order to promote the use of natural fibers in noise and vibration applications, the properties of these structures should be fully identified. The sound absorption coefficients (SACs) and transmission losses (TLs) of green luffa fiber samples are thoroughly investigated and their acoustic performances are compared with the acoustic performances of green homogenous jute and hybrid jute/luffa fiber samples in this study. For this purpose, green homogenous luffa and jute fiber samples and their green hybrid fiber samples with different thicknesses (10, 20, 30, and 40 mm) are produced and their SACs and TLs are determined using the impedance tube method. First, the methods for the experimental identification of acoustic properties are presented and the variations in the measured acoustic properties are identified. After that, the effects of sample thickness on the acoustic performances of homogenous luffa as well as jute samples and their hybrid fiber samples as a function of frequency are explored. The thickness-dependent tendencies of the SACs and TLs of homogenous and hybrid luffa and jute fiber samples for low, medium and high frequency ranges are determined. Then, the acoustic performances of the homogenous and hybrid luffa and jute samples are compared and evaluated. The results and analyses for the acoustic properties of homogeneous luffa and jute fiber samples and their hybrid fiber samples for a variety of thicknesses and different frequencies presented here can be used to design homogenous as well as hybrid luffa and jute fiber structures in practical applications.

Laboratory and in situ sound absorption measurement under a synthetized diffuse acoustic field

2019 ◽  
Vol 26 (4) ◽  
pp. 223-242
Author(s):  
Olivier Robin ◽  
Alain Berry ◽  
Celse Kafui Amédin ◽  
Noureddine Atalla ◽  
Olivier Doutres ◽  
...  
Keyword(s):  
Acoustic Field ◽  
Sound Absorption ◽  
Low Frequency ◽  
Sound Field ◽  
Geometrical Parameters ◽  
In Situ Conditions ◽  
Field Excitation ◽  
Acoustic Environments ◽  
Field Sound

This article reports numerical and experimental results concerning the estimation of the diffuse field sound absorption coefficient of several different materials under a synthetized diffuse acoustic field excitation in laboratory and in situ conditions. The proposed measurement method is based on a sound field reproduction approach and a synthetic array of acoustic monopoles facing the material to be tested. Numerical simulations are first conducted to optimize the geometrical parameters of the method and to compute theoretical sound absorption coefficients of the considered materials. Measurements on a set of six typical acoustic materials are then conducted following the standardized reverberant room method as well as the proposed approach in a hemi-anechoic room and in two realistic rooms. Albeit showing limitations in the low-frequency domain, the proposed method enables a significant reduction of the tested specimen dimensions compared with the reverberant room method and allows performing tests in non-ideal acoustic environments.

Sign in / Sign up

Export Citation Format

Share Document