Inverse Kinematics Model of a Bucket Excavator’s Digging Equipment

2015 ◽  
Vol 762 ◽  
pp. 11-19
Author(s):  
Marian Dima ◽  
Cătălin Frâncu
Keyword(s):  
Matrix Method ◽  
Inverse Kinematics ◽  
Geometric Model ◽  
Forward Kinematics ◽  
Kinematics Model ◽  
The Matrix

This paper presents a method to build the inverse kinematics model of a bucket excavator’s digging equipment. The model is determined by using two different methods, the matrix method applied on the decoupled forward kinematics model and respectively the geometric model.

Research on the Kinematics of Line Heating Robot Based on SVM

2014 ◽  
Vol 668-669 ◽  
pp. 361-365
Author(s):  
Yan Li ◽  
You Li Chen
Keyword(s):  
Inverse Kinematics ◽  
Geometric Model ◽  
Forward Kinematics ◽  
Robot Kinematics ◽  
Support Vector ◽  
Line Heating ◽  
Kinematics Model ◽  
Heating Plate ◽  
Kinematics Modeling ◽  
Complex Trajectory

The paper mainly analyzed the robot kinematics of the line heating plate. In order to realize the moving of complex trajectory for the robot, a forward kinematics modeling and the simulation of inverse kinematics are carried out. Firstly, with the D-H modeling method, the line heating plate robot forward kinematics equations and the spatial geometric model of the manipulator are set up, then multi-input multi-output systems based on support vector machines algorithm is used to establish the inverse kinematics model for the robot . At last, the simulations of tracing complex trajectory with the inverse kinematics model are carried out, and the results show that the model derived by SVM can trace the trajectory very well.

Machining Performance Evaluation of Robot Type Machine Tool Based on Forward Kinematics Model

2020 ◽  
Author(s):  
Akio Hayashi ◽  
Masato Ueki ◽  
Keisuke Nagao ◽  
Hiroto Tanaka ◽  
Yoshitaka Morimoto ◽  
...  
Keyword(s):  
Machine Tools ◽  
Geometric Model ◽  
Forward Kinematics ◽  
Machining Accuracy ◽  
Machining Performance ◽  
Kinematics Model ◽  
Link Mechanism ◽  
Conventional Machine ◽  
Type Machine ◽  
Parallel Link

Abstract Robot type machine tools with parallel link mechanism are characterized by the performance to change tool posture and machine wider range than conventional machine tools. It is realized by simultaneous multi-axis control of parallel link mechanism. However, there are some problems, it is difficult to identify and adjust alignment error. In addition, the machining performance is unidentified due to the rigidity is different from conventional machine tools. In this research, a geometric model is described and the forward kinematics model is derived based on the geometric model. Then, the machining tests were carried out to evaluate the machining accuracy by measured machined surface and the simulated motion of tool cutting edge based on proposed forward kinematics model.

Analysis of the Kinematics of an Eight-Wheeled Mobile Platform

2013 ◽  
Vol 198 ◽  
pp. 67-72
Author(s):  
Marek Stania
Keyword(s):  
Inverse Kinematics ◽  
Object Motion ◽  
Forward Kinematics ◽  
Contact Phenomenon ◽  
Kinematics Model ◽  
Inverse Kinematics Problem ◽  
Transport Vehicle ◽  
Forward And Inverse Kinematics ◽  
Motion Parameters ◽  
Simulation Results

This paper presents the modeling problem connected with the autonomous transport vehicle designed at Hochschule Ravensburg-Weingarten. The forward and inverse kinematics problem of eight-wheeled autonomous transport vehicle have been formulated and solved, additionally examples of simulation results representing the changes of individual motion parameters have been presented. Contact phenomenon between foundation and drive wheel has been taken into account in the kinematics model. Motion trajectory and velocity of the selected point belonging to the platform have been intended while the inverse kinematics problem has been solved. The forward kinematics problem has been worked out in order to verify correctness of the studied kinematics model. The presented simulation results point out compatibility of the worked out kinematics model of investigated object. The worked out models allow carrying out analysis of object motion through simulation investigations on the basis of proposed computational model.

scholarly journals Forward Kinematics Model for Evaluation of Machining Performance of Robot Type Machine Tool

2021 ◽  
Vol 15 (2) ◽  
pp. 215-223
Author(s):  
Akio Hayashi ◽  
Hiroto Tanaka ◽  
Masato Ueki ◽  
Hidetaka Yamaoka ◽  
Nobuaki Fujiki ◽  
...  
Keyword(s):  
Machine Tool ◽  
Machine Tools ◽  
Geometric Model ◽  
Forward Kinematics ◽  
Machining Accuracy ◽  
Machining Performance ◽  
Machined Surface ◽  
Kinematics Model ◽  
Tool Posture ◽  
Type Machine

Robot-type machine tools are characterized by the ability to change the tool posture and machine itself with a wider motion range than conventional machine tools. The motion of the robot machine tool is realized by simultaneous multi-axis control of link mechanisms. However, when the robot machine tool performs a general milling process, some problems that affect the machining accuracy occur. Moreover, it is difficult to identify the motion errors of each axis, which influence machining accuracy. Thus, it is difficult to adjust the servo gain and alignment error. In addition, the machining performance is unidentified because of the rigidity differences when the posture changes. In this study, the focus was on robot-type machine tools consisting of a serial and a parallel link mechanism. A geometric model is described, and the forward kinematics model is derived based on the geometric model. Machining tests were then carried out to evaluate the machining accuracy by measuring the machined surfaces and the simulated motion of the tool posture based on the proposed forward kinematics model to identify the mechanism that affects the machined surface roughness and surface waviness. As a result, it was shown that the proposed model can separate and reproduce the behavior of each axis of the machine. Finally, it was clarified that the behavior of the second axis has a great influence on the tool posture and machined surface.

Mechanism Design and Kinematics Simulation of Massage Mechanical Arm

2011 ◽  
Vol 101-102 ◽  
pp. 279-282 ◽  
Author(s):  
Jun Xie ◽  
Jun Zhang ◽  
Jie Li
Keyword(s):  
Mechanism Design ◽  
Three Dimensional ◽  
Forward Kinematics ◽  
Kinematics Analysis ◽  
Dimensional Model ◽  
Three Dimensional Model ◽  
Kinematics Model ◽  
Kinematics Simulation ◽  
The Common ◽  
Executive Mechanism

Based on the characteristics and the common massage manipulations of Chinese medical massage, a practical series mechanical arm was presented to act the manipulations with the parallel executive mechanism. Forward kinematics was solved by the Denavit-Hartenberg transformation after the kinematics model of the arm was established. And the three-dimensional model of the arm was created by Pro/E and was imported into ADAMS for the kinematics analysis. The results indicated that the common massage manipulations could be simulated by the arm correctly and flexibly, and it verified the accuracy of the mechanism design of the arm.

Mechanism Design and Simulation of the ULTRA Spine: A Tensegrity Robot

2015 ◽  
Author(s):  
Andrew P. Sabelhaus ◽  
Hao Ji ◽  
Patrick Hylton ◽  
Yakshu Madaan ◽  
ChanWoo Yang ◽  
...  
Keyword(s):  
Mechanism Design ◽  
Design Process ◽  
Inverse Kinematics ◽  
Gear Ratio ◽  
Forward Kinematics ◽  
Robot Design ◽  
Link Structure ◽  
Iterative Design ◽  
Quadruped Robots ◽  
Ongoing Effort

The Underactuated Lightweight Tensegrity Robotic Assistive Spine (ULTRA Spine) project is an ongoing effort to create a compliant, cable-driven, 3-degree-of-freedom, underactuated tensegrity core for quadruped robots. This work presents simulations and preliminary mechanism designs of that robot. Design goals and the iterative design process for an ULTRA Spine prototype are discussed. Inverse kinematics simulations are used to develop engineering characteristics for the robot, and forward kinematics simulations are used to verify these parameters. Then, multiple novel mechanism designs are presented that address challenges for this structure, in the context of design for prototyping and assembly. These include the spine robot’s multiple-gear-ratio actuators, spine link structure, spine link assembly locks, and the multiple-spring cable compliance system.

Comparison of Inverse Kinematics Algorithms for Multi-Section Continuum Robots

2021 ◽  
Vol 22 (8) ◽  
pp. 420-424
Author(s):  
D. Yu. Kolpashchikov ◽  
O. M. Gerget
Keyword(s):  
Inverse Kinematics ◽  
Complex Geometry ◽  
Forward Kinematics ◽  
Non Destructive Testing ◽  
Invasive Procedures ◽  
Destructive Testing ◽  
Continuum Robots ◽  
Unique Type ◽  
Non Destructive ◽  
Constant Section

Continuum robots are a unique type of robots that move due to the elastic deformation of their own body. Their flexible design allows them to bend at any point along their body, thus making them usable in workspaces with complex geometry and many obstacles. Continuum robots are used in industry for non-destructive testing and in medicine for minimally invasive procedures and examinations. The kinematics of continuum robots consisting of a single bending section are well known, as is the forward kinematics for multi-section continuum robots. There exist efficient algorithms for them. However, the problem of inverse kinematics for multi-section continuum robots is still relevant. The complexity of the inverse kinematics for multi-section continuum robots is quite high due to the nonlinearities of the robots’ motion. The article discusses in detail the modification of the FABRIK algorithm proposed by the authors, as well as a Jacobian-based iterative algorithm. A comparison of inverse kinematics algorithms for multi-section continuum robots with constant section length is given and the results of the experiment are described.

Sign in / Sign up

Export Citation Format

Share Document