Effect of Additional Shear Strain Layer on Microstructure and Tensile Strength of Fine Wire

2007 ◽  
Vol 340-341 ◽  
pp. 525-530 ◽  
Author(s):  
Satoshi Kajino ◽  
Motoo Asakawa

The mechanical and electrical applications of fine wires (D = 0.1 mm) has become more widely spread. In general, it is well known that fine drawn wires have high tensile strength while maintaining ductility. It has been determined that a hardened layer of around 0.04 mm in depth, referred to as the “additional shear strain layer,” is generated beneath the surface layer of the wire, and this additional shear strain layer affected the tensile strength of the fine wire. As an origin of this phenomenon, it was ascertained that the microstructure of surface layer was finer than that of center layer. The purpose of this paper is to investigate the effect of die angle on the microstructure and the tensile strength of the additional shear strain layer. The tensile test was performed as the surface layer was thinned by electro-polishing, and the crystal orientation and the crystal grain were measured via EBSD. As a result, it was ascertained that die angle affected the tensile strength and crystal grain refinement of the additional shear stray layer.

2007 ◽  
Vol 2007.15 (0) ◽  
pp. 225-226
Author(s):  
Satoshi KAJINO ◽  
Motoo ASAKAWA ◽  
Kazuki HOSODA ◽  
Yasuhiro MAEDA

2000 ◽  
Vol 2000.8 (0) ◽  
pp. 369-370
Author(s):  
Hiroyuki MIZUNO ◽  
Kentaroh YAMAGUTI ◽  
Ikuo OCHIAI. ◽  
Motoh ASAKAWA

Alloy Digest ◽  
2020 ◽  
Vol 69 (9) ◽  

Abstract Lucefin Group C30, C30E, and C30R are medium-carbon, non-alloy steels that are used in the normalized, cold worked, or quenched and tempered condition. C30E and C30R may also be flame or induction hardened. C30, C30E, and C30R are widely used for small, moderately stressed parts, where higher strength levels are needed than can be achieved in the lower carbon grades, and also where toughness is more important than high tensile strength. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties. It also includes information on forming, heat treating, machining, and joining. Filing Code: CS-206. Producer or source: Lucefin S.p.A.


Alloy Digest ◽  
1997 ◽  
Vol 46 (10) ◽  

Abstract Vasco 9-4-20 (0.20 wt% C) is a premium quality aircraft steel that combines high tensile strength with good fracture toughness. It is a heat-treatable alloy capable of developing an ultimate tensile strength greater than 190 ksi. This datasheet provides information on composition, physical properties, hardness, elasticity, and tensile properties as well as fracture toughness. It also includes information on high temperature performance as well as heat treating, machining, and joining. Filing Code: SA-489. Producer or source: Vasco, An Allegheny Teledyne Company.


Alloy Digest ◽  
1976 ◽  
Vol 25 (12) ◽  

Abstract NJZ Alloy No. 55 is a zinc-cadmium alloy characterized by high tensile strength and hardness but low ductility. It has high stiffness and resiliency but low drawing and forming characteristics. Its applications include hardware and medallions. This datasheet provides information on composition, physical properties, hardness, and tensile properties as well as creep and fatigue. It also includes information on corrosion resistance as well as casting, forming, heat treating, machining, and joining. Filing Code: Zn-30. Producer or source: New Jersey Zinc Company.


ACS Omega ◽  
2021 ◽  
Vol 6 (4) ◽  
pp. 2890-2898
Author(s):  
Xiaojiao Jiao ◽  
Jiangling Liu ◽  
Jing Jin ◽  
Fei Cheng ◽  
Yunxin Fan ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document