Low-Cycle Fatigue Life Prediction by a New Critical-Plane Method

2008 ◽  
Vol 385-387 ◽  
pp. 209-212
Author(s):  
Dan Jin ◽  
Jian Hua Wu ◽  
Yang Zhang
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Weight Function ◽  
Life Prediction ◽  
Low Cycle Fatigue ◽  
304 Stainless Steel ◽  
Cycle Fatigue ◽  
Critical Plane ◽  
Plane Method ◽  
Rainflow Cycle Counting

A series of low-cycle fatigue experiments of axial-torsional loading of variable amplitudes were performed on the tubular specimens of 304 stainless steel. Two models of multiaxial low-cycle fatigue life, KBM and FS method, are evaluated based on the fatigue life data of 304 stainless steel. Rainflow cycle counting and the Liner Damage Rule are used to calculate fatigue damage. It was shown that the part prediction results are nonconservative for the two models. The life prediction is done again based on the weight function critical plane method for the two models. The prediction results are better by using the weight function critical plane method than the previous results for KBM model. But the prediction results are improved little for FS model in spite of the weight function critical plane method being used.

A weight function method for multiaxial low-cycle fatigue life prediction under variable amplitude loading

2018 ◽  
Vol 53 (4) ◽  
pp. 197-209 ◽  
Author(s):  
Xiao-Wei Wang ◽  
De-Guang Shang ◽  
Yu-Juan Sun
Keyword(s):  
Fatigue Life ◽  
Weight Function ◽  
Life Prediction ◽  
Function Method ◽  
Low Cycle Fatigue ◽  
Fatigue Life Prediction ◽  
Cycle Fatigue ◽  
Critical Plane ◽  
Variable Amplitude ◽  
Weight Function Method

A weight function method based on strain parameters is proposed to determine the critical plane in low-cycle fatigue region under both constant and variable amplitude tension–torsion loadings. The critical plane is defined by the weighted mean maximum absolute shear strain plane. Combined with the critical plane determined by the proposed method, strain-based fatigue life prediction models and Wang-Brown’s multiaxial cycle counting method are employed to predict the fatigue life. The experimental critical plane orientation and fatigue life data under constant and variable amplitude tension–torsion loadings are used to verify the proposed method. The results show that the proposed method is appropriate to determine the critical plane under both constant and variable amplitude loadings.

An Experimental Evaluation for Four Multiaxial Fatigue Approaches

2014 ◽  
Vol 627 ◽  
pp. 425-428
Author(s):  
Dan Jin ◽  
Da Jiang Tian ◽  
Qi Zhou Wu ◽  
Wei Lin
Keyword(s):  
Low Cycle Fatigue ◽  
Multiaxial Fatigue ◽  
304 Stainless Steel ◽  
Normal Strain ◽  
Cycle Fatigue ◽  
Critical Plane ◽  
Maximum Shear Strain ◽  
Rainflow Cycle Counting ◽  
Tubular Specimens ◽  
Damage Rule

A series of tests for low cycle fatigue were conducted on the tubular specimens for 304 stainless steel under variable amplitude and irregular axial-torsional loading. Rainflow cycle counting and linear damage rule are used to calculate fatigue damage and four approaches, e.g. SWT(Smith-Watson-Topper), KBM(Kandil-Brown-Miller), FS(Fatemi-Socie), and LKN(Lee-Kim-Nam) approach are employed to predict the fatigue life. The maximum shear strain plane, the maximum normal strain plane, and the maximum damage plane are considered as the critical plane, respectively. The effects of the choice of the critical plane on previous approaches are discussed. It is shown that comparing with the maximum shear/normal strain approach, the predictions are improved by using the maximum damage plane approach, part nonproportional paths for SWT, AV and part nonproportional paths for KBM, TV paths for FS. But for LKN, the prediction results are nonconservative for some paths than that of the maximum shear/normal strain approach.

Low Cycle Fatigue of Nuclear Pipe Components

1974 ◽  
Vol 96 (3) ◽  
pp. 171-176 ◽  
Author(s):  
J. D. Heald ◽  
E. Kiss
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Room Temperature ◽  
Fatigue Testing ◽  
Low Cycle Fatigue ◽  
304 Stainless Steel ◽  
Code Design ◽  
Hydraulic Pressure ◽  
Cycle Fatigue ◽  
Cyclic Bending

This paper presents the results of low-cycle fatigue testing and analysis of 26 piping components and butt-welded sections. The test specimens were fabricated from Type-304 stainless steel and carbon steel, materials which are typically used in the primary piping of light water nuclear reactors. Components included 6-in. elbows, tees, and girth butt-welded straight sections. Fatigue testing consisted of subjecting the specimens to deflection-controlled cyclic bending with the objective of simulating system thermal expansion type loading. Tests were conducted at room temperature and 550 deg F, with specimens at room temperature subjected to 1050 psi constant internal hydraulic pressure in addition to cyclic bending. In two tests at room temperature, however, stainless steel elbows were subjected to combined simultaneous cyclic internal pressure and cyclic bending. Predictions of the fatigue life of each of the specimens tested have been made according to the procedures specified in NB-3650 of Section III[1] in order to assess the code design margin. For the purpose of the assessment, predicted fatigue life is compared to actual fatigue life which is defined as the number of fatigue cycles producing complete through-wall crack growth (leakage). Results of this assessment show that the present code fatigue rules are adequately conservative.

A New Nonproportional Low Cycle Fatigue Life Prediction Method for Type 304 Stainless Steel

2019 ◽  
Vol 141 (2) ◽  
Author(s):  
Bowen Liu ◽  
Xiangqiao Yan
Keyword(s):  
Stainless Steel ◽  
Fatigue Life ◽  
Life Prediction ◽  
Low Cycle Fatigue ◽  
Prediction Method ◽  
Fatigue Life Prediction ◽  
New Method ◽  
304 Stainless Steel ◽  
Loading Path ◽  
Prediction Approach

A new method is put forward to predict fatigue life for low cycle nonproportional loading based on the Itoh criterion. The proposed method considers the multi-axiality influence on the reference maximum principal strain path and the calculation of nonproportionality factor Fnp by utilizing a multi-axial fatigue life prediction approach based on the modified Wöhler curve method. Different from the hypothesis of previous integral models for computing factor Fnp where the loading path is considered uniform, a new model using an inhomogeneous integral is presented and a path-dependent weight factor is defined to describe this inhomogeneity. The experimental tests of Itoh on 304 stainless steel with 14 different loading cases are referenced to examine the validity of the new method.

Sign in / Sign up

Export Citation Format

Share Document