Influence of Loading History on Delamination in Multilayered Beam with Creep

2021 ◽  
Vol 1046 ◽  
pp. 23-28
Author(s):  
Victor Iliev Rizov
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Time Dependent ◽  
External Loading ◽  
Loading History ◽  
Multilayered Beam

The present paper deals with an analytical study of the time-dependent delamination in a multilayered inhomogeneous cantilever beam with considering of the loading history. The multilayered beam exhibits creep behaviour that is treated by using a non-linear stress-strain-time relationship. The material properties are continuously distributed along the thickness and length of the layers. The external loading is applied in steps in order to describe the loading history. The analysis reveals that during each step of the loading, the strain energy release rate increases with time. The influences of crack length and location on the time-dependent strain energy release rate are also investigated.

Longitudinal vertical crack analysis in beam with relaxation stresses

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Victor Rizov
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Viscoelastic Model ◽  
Strain Energy Release ◽  
Time Dependent ◽  
Content Type ◽  
Dependent Strain

Purpose This paper is concerned with analysis of the time-dependent strain energy release rate for a longitudinal crack in a beam subjected to linear relaxation. A viscoelastic model with an arbitrary number of parallel units is used for treating the relaxation. Each unit has one dashpot and two springs. A stress-strain-time relationship is derived for the case when the coefficient of viscosity in each unit of the viscoelastic model changes continuously with time. The beam exhibits continuous material inhomogeneity along the thickness. Thus, the moduli of elasticity and the coefficients of viscosity vary continuously in the thickness direction. The aim of the present paper is to obtain time-dependent solutions to the strain energy release rate that take into account the relaxation when the coefficient of viscosity changes with time. Design/methodology/approach Time-dependent solutions to the strain energy release rate are derived by considering the time-dependent strain energy and also by using the compliance method. The two solutions produce identical results. Findings The variation of the strain energy release rate with time due to the relaxation is analysed. The influence of material inhomogeneity and the crack location along the beam width on the strain energy release rate are evaluated. The effects of change of the coefficients of viscosity with time and the number of units in the viscoelastic model on the strain energy release rate are assessed by applying the solutions derived. Originality/value The time-dependent strain energy release rate for a longitudinal vertical crack in a beam under relaxation is analysed for the case when the coefficients of viscosity change with time.

Influence of Creep on Longitudinal Fracture of Inhomogeneous Rod Loaded in Torsion and Bending

2021 ◽  
Vol 1046 ◽  
pp. 9-14
Author(s):  
Victor Iliev Rizov
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Linear Time ◽  
Circular Cross Section ◽  
Strain Energy Release ◽  
Time Dependent ◽  
Material Inhomogeneity

The present paper analyzes the influence of creep on longitudinal fracture in continuously inhomogeneous rod of circular cross-section loaded in torsion and bending. The rod exhibits continuous material inhomogeneity in both radial and longitudinal directions. The creep is described by using non-linear time-dependent relations between the principle stresses and strains. A time-dependent solution to the strain energy release rate is derived by analyzing the complementary strain energy. The time-dependent strain energy release rate is found also by considering the energy balance for verification. The solutions are applied to perform a parametric study of the strain energy release rate under creep.

On the Axial Rigidity of a Perforated Strip and the Strain Energy Release Rate in a Centrally Notched Strip Subjected to Uniaxial Tension

1964 ◽  
Vol 86 (4) ◽  
pp. 693-697 ◽  
Author(s):  
R. G. Forman ◽  
A. S. Kobayashi
Keyword(s):  
Energy Release Rate ◽  
Energy Release ◽  
Uniaxial Tension ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Theoretical Studies ◽  
Correction Factors ◽  
Elasticity Solutions

This paper presents theoretical studies on the axial rigidities in strips with circular and elliptical perforations and subjected to uniaxial tension. Greenspan’s original derivations on these axial rigidities [2] were improved by using the elasticity solutions by Howland [6] and Ishida [7] for infinite strips with circular and elliptical perforations, respectively. Finally, the correction factors for centrally notched strips subjected to uniaxial tension were rederived from the above results following the energy approach by Irwin and Kies [3].

Nonlinear Approach for Strain Energy Release Rate in Micro Cantilevers

2010 ◽  
Author(s):  
Arash Kheyraddini Mousavi ◽  
Seyedhamidreza Alaie ◽  
Maheshwar R. Kashamolla ◽  
Zayd Chad Leseman
Keyword(s):  
Surface Roughness ◽  
Crack Propagation ◽  
Energy Release Rate ◽  
Energy Release ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Rigid Substrate ◽  
Micro Cantilever

An analytical Mixed Mode I & II crack propagation model is used to analyze the experimental results of stiction failed micro cantilevers on a rigid substrate and to determine the critical strain energy release rate (adhesion energy). Using nonlinear beam deflection theory, the shape of the beam being peeled off of a rigid substrate can be accurately modeled. Results show that the model can fit the experimental data with an average root mean square error of less than 5 ran even at relatively large deflections which happens in some MEMS applications. The effects of surface roughness and/or debris are also explored and contrasted with perfectly (atomically) flat surfaces. Herein it is shown that unlike the macro-scale crack propagation tests, the surface roughness and debris trapped between the micro cantilever and the substrate can drastically effect the energy associated with creating unit new surface areas and also leads to some interesting phenomena. The polysilicon micro cantilever samples used, were fabricated by SUMMIT V™ technology in Sandia National Laboratories and were 1000 μm long, 30 μm wide and 2.6 μm thick.

Effect of Plastic Deformation on the Strain Energy Release Rate in a Centrally Notched Plate Subjected to Uniaxial Tension

1966 ◽  
Vol 88 (1) ◽  
pp. 82-86 ◽  
Author(s):  
R. G. Forman
Keyword(s):  
Plastic Deformation ◽  
Energy Release Rate ◽  
Energy Release ◽  
Uniaxial Tension ◽  
Correction Factor ◽  
Release Rate ◽  
Strain Energy ◽  
Strain Energy Release Rate ◽  
Strain Energy Release ◽  
Linear Elastic

This paper presents theoretical studies on the effect of plastic deformation on the strain energy release rate, G, of a plate under uniaxial tension with a central propagating crack. The linear elastic fracture mechanics solution for G is improved by using the Dugdale model for the crack and yielded region to obtain the axial rigidity of the plate. The axial rigidity is then used to obtain the solution for the strain energy release rate as the crack propagates. It is found that plastic deformation has a pronounced effect on G. A correction factor is presented for correcting the linear elastic solution for the strain energy release rate. The correction factor is found to depend upon the nominal (gross) stress to material yield stress ratio and the crack length to plate width ratio.

Sign in / Sign up

Export Citation Format

Share Document