Evaluation of Wedge Splitting Fracture Tests Using the Double-K Model: Analysis of the Effect of Hemp Fibre Dosage and Length in Concrete Specimens

2016 ◽  
Vol 249 ◽  
pp. 142-146
Author(s):  
Hana Šimonová ◽  
Ivana Havlíková ◽  
Jakub Sobek ◽  
Alaa Abdulrahman ◽  
Zbyněk Keršner ◽  
...  
Keyword(s):  
Fracture Toughness ◽  
Crack Propagation ◽  
Crack Opening Displacement ◽  
Crack Opening ◽  
Opening Displacement ◽  
Critical Crack ◽  
Hemp Fibre ◽  
Fracture Tests ◽  
Critical Crack Opening ◽  
Wedge Splitting

This paper deals with the results obtained from the employment of a selected fracture model to evaluate wedge splitting fracture tests carried out on hemp fibre concrete specimens. The research work was focused mainly on the effect of the dosage and length of hemp fibres on the initiation part of crack propagation in concrete specimens, and on critical crack opening displacement. Concrete mixtures with different volumetric dosages (0.5, 1.0 and 2.0 %) and fibre lengths (10, 20 and 40 mm) were prepared, and six identical specimens were cast from each mixture. Specimens were also cast from a reference mixture, which was without fibres. The specimens were provided with an initial notch and tested using the wedge splitting test method. Load versus crack mouth opening displacement diagrams were recorded during testing and (after data filtering and appropriate modifications) subsequently evaluated using the Double-K fracture model. This model allows the evaluation of two material parameters – the initiation fracture toughness, which defines the onset of stable crack propagation, and the unstable fracture toughness, which defines the onset of unstable cracking or failure. Finally, the critical crack opening displacement was determined with the assumption of the bilinear function of softening in tension.

Test for Crack Opening Displacement of Steel Fiber Reinforced Concrete under Three-Point Bending

2010 ◽  
Vol 36 ◽  
pp. 157-161 ◽  
Author(s):  
Tin Gyi Zhang ◽  
Yuan Bao Leng ◽  
Dan Ying Gao
Keyword(s):  
Crack Opening Displacement ◽  
Crack Opening ◽  
Mouth Opening ◽  
Crack Tip ◽  
Crack Mouth Opening Displacement ◽  
Crack Tip Opening Displacement ◽  
Opening Displacement ◽  
Critical Crack ◽  
Critical Crack Opening ◽  
Crack Tip Opening

Based on the principle of electrical measurement method, the clip gauge was made to measure the crack opening displacement (COD).Through the three-point bending test on the specimens of steel fiber reinforced high strength concrete (SFHSC), the effect of the fiber volume fraction (ρf) upon the critical crack opening displacement (the critical crack tip opening displacement and the critical crack mouth opening displacement) was studied. The result shows that the effect of ρf on mouth-tip ratio (the ratio of critical crack mouth opening displacement to critical crack tip opening displacement) can reflect its effect upon the critical crack opening displacement. According to the geometrical relationship between the initial crack length and the critical crack opening displacement，calculation method for the initial crack length was proposed. Based on the test result, the formula was established for calculating the critical crack tip opening displacement.

scholarly journals Toughness Calculation of Postfire Normal Concrete

2014 ◽  
Vol 2014 ◽  
pp. 1-8
Author(s):  
Qingyang Chen ◽  
Anjing Tang ◽  
Zhoudao Lu
Keyword(s):  
Fracture Toughness ◽  
Critical Load ◽  
Crack Opening Displacement ◽  
Analytical Method ◽  
Crack Opening ◽  
Fracture Model ◽  
Opening Displacement ◽  
Normal Concrete ◽  
Critical Fracture ◽  
Fracture Tests

Fracture tests of postfire normal concrete with ten temperatures up to 600°C are implemented. Residual fracture toughness using analytical method is determined. Two situations are divided at critical load when calculating the cohesive fracture toughness. The initial and critical fracture toughness could be calculated from the complete load-crack opening displacement curves. Finally, the validation of double-Kfracture model to the postfire concrete specimens is proved.

Fracture Tests Of Polysilicon Film

1997 ◽  
Vol 505 ◽  
Author(s):  
W. N. Sharpe ◽  
B. Yuan ◽  
R. L. Edwards
Keyword(s):  
Thin Films ◽  
Fracture Toughness ◽  
Crack Opening Displacement ◽  
Crack Opening ◽  
Tensile Loading ◽  
Opening Displacement ◽  
Polysilicon Film ◽  
Fracture Tests

ABSTRACTA new test approach is presented to measure the fracture toughness of thin films. The polysilicon specimen is a center-cracked panel that is 3.5 μm thick and 3 mm wide with a 100 μm long slot in the center. It is subjected to tensile loading, and the crack-opening displacement is measured by interferometry. The average toughness is 1.4 ± 0.65 MPa-m1/2.

The crack opening displacement approach to fracture mechanics in yielding materials

1966 ◽  
Vol 1 (2) ◽  
pp. 145-153 ◽  
Author(s):  
F. M. Burdekin ◽  
D. E. W. Stone
Keyword(s):  
Fracture Mechanics ◽  
Crack Opening Displacement ◽  
Crack Opening ◽  
Opening Displacement ◽  
Critical Crack ◽  
Absolute Size ◽  
Linear Elastic ◽  
Elastic Fracture ◽  
Critical Crack Opening ◽  
Displacement Approach

An introduction is given to the fracture mechanics approach employing the concept of crack opening displacement for application to situations in which linear elastic fracture mechanics is invalidated by yielding. The hypothesis of a critical crack opening displacement to fracture has been examined experimentally using mild steel specimens of vastly differing dimensions. Subsidiary experiments have been carried out to define the factors responsible for the apparent effect of absolute size on the results. A theoretical analysis simulates elastic-plastic conditions to give a relationship between applied stresses and strains, crack length, and crack opening displacement.

A New Methodology for Estimating Fracture Criterion of Thin Sheets

2009 ◽  
Vol 417-418 ◽  
pp. 305-308
Author(s):  
Kalyan Kumar Ray ◽  
Ashmita Patra ◽  
Debashish Bhattacharjee
Keyword(s):  
Fracture Toughness ◽  
Crack Opening ◽  
Specimen Thickness ◽  
Interstitial Free ◽  
Thin Sheets ◽  
If Steel ◽  
Opening Displacement ◽  
Critical Crack ◽  
Suggested Technique ◽  
Critical Crack Opening

A simple and reliable method has been proposed for determining fracture toughness of thin sheets. The principle of the method considers that critical crack opening displacement (c) corresponds to a specific amount of load drop during fracture toughness tests. The suggested technique yields c value for an interstitial free (IF) steel as 2.04 mm in excellent correspondence with an indirect estimate of 1.97 mm from the popular energy extrapolation technique. The magnitude of c for IF steel sheets is found to decrease with decreasing thickness in agreement with the expected variation of this criterion with specimen thickness in gross yielding fracture mechanics (GYFM) regime.

Sign in / Sign up

Export Citation Format

Share Document