scholarly journals Characteristics of Chemical Composition and Particle Size Distribution from Real Coal-fired Circulating Fluidised Bed (CFB) Boiler

2021 ◽  
Vol 21 ◽  
Author(s):  
Xin Du ◽  
Jianhui Wu ◽  
Yingze Tian ◽  
Yufen Zhang ◽  
Baoshuang Liu ◽  
...  
2019 ◽  
Vol 2 (98) ◽  
pp. 81-84
Author(s):  
K. Szmajnta ◽  
M. Szindler

Purpose: The main purpose of this publication is to bring closer method of synthesis and examining basic properties of TiO2, ZnO and NiO nanoparticles (NPs), and investigate their possible biomedical application. Design/methodology/approach: Nanopowders were made with sol-gel method. Surface morphology studies of the obtained materials were made using Zeiss's Supra 35 scanning electron microscope and the structure using S/TEM TITAN 80-300 transmission electron microscope. In order to confirm the chemical composition of observed nanopowders, qualitative tests were performed by means of spectroscopy of scattered X -ray energy using the Energy Dispersive Spectrometer (EDS). The DLS (Dynamic Light Scattering) method was used to analyse the particle size distribution using the AntonPaar Litesizer 500 nanoparticle size analyser. Changes in particle size distribution at elevated temperatures were also observed. The TiO2, ZnO and NiO NPs with spherical shape were successfully produced by sol-gel method. Findings: The diameter of the as prepared nanoparticles does not exceed 25 nm which is confirmed by the TEM analysis. The highest proportion among the agglomerates of the nanoparticles has been shown to show those with a diameter of 80 to 125 nm. The qualitative analysis of EDS confirmed the chemical composition of the material. Practical implications: Nanoparticles (NPs) has been receiving an incrementally increasing interest within biomedical fields researchers. Nanoparticles properties (physical, chemical, mechanical, optical, electrical, magnetic, etc.) are different from the properties of their counterparts with a larger particle size. Originality/value: The nanoparticles were prepared using sol-gel method which allows the particle size to be controlled in a simple way.


Atmosphere ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 56 ◽  
Author(s):  
Ankang Liu ◽  
Honglei Wang ◽  
Yi Cui ◽  
Lijuan Shen ◽  
Yan Yin ◽  
...  

Particle size distribution, water soluble ions, and black carbon (BC) concentration in a long-term haze-fog episode were measured using a wide-range particle spectrometer (WPS), a monitor for aerosols and gases (MARGA), and an aethalometer (AE33) in Nanjing from 16 to 27 November, 2018. The observation included five processes of clean, mist, mix, haze, and fog. Combined with meteorological elements, the HYSPLIT model, and the IMPROVE model, we analyzed the particle size distribution, chemical composition, and optical properties of aerosols in different processes. The particle number size distribution (PNSD) in five processes differed: It was bimodal in mist and fog and unimodal in clean, mix, and haze. The particle surface area size distribution (PSSD) in different processes showed a bimodal distribution, and the second peak of the mix and fog processes shifted to a larger particle size at 480 nm. The dominant air masses in five processes differed and primarily originated in the northeast direction in the clean process and the southeast direction in the haze process. In the mist, mix, and fog processes local air masses dominated. NO3− was the primary component of water soluble ions, with the lowest proportion of 45.6% in the clean process and the highest proportion of 53.0% in the mix process. The ratio of NH4+ in the different processes was stable at approximately 23%. The ratio of SO42− in the clean process was 26.2%, and the ratio of other processes was approximately 20%. The average concentration of BC in the fog processes was 10,119 ng·m−3, which was 3.55, 1.80, 1.60, and 1.46 times that in the processes of clean, mist, mix, and haze, respectively. In the different processes, BC was primarily based on liquid fuel combustion. NO3−, SO42−, and BC were the main contributors to the atmospheric extinction coefficient and contributed more than 90% in different processes. NO3− contributed 398.43 Mm−1 in the mix process, and SO42− and BC contributed 167.90 Mm−1 and 101.19 Mm−1, respectively, during the fog process.


Clay Minerals ◽  
1998 ◽  
Vol 33 (1) ◽  
pp. 65-75 ◽  
Author(s):  
E. Galan ◽  
P. Aparicio ◽  
I. Gonzalez ◽  
A. Miras

AbstractAccording to multivariate analysis, the following were established (a) kaolinite crystallinity index (KCI) values determined by XRD are highly correlated to one another and seemingly influenced by kaolin impurities; (b) kaolin minerals are concentrated mainly in the fractions <4 µm; (c) the kaolin surface area as determined by the BET (nitrogen adsorption) method is more markedly affected by kaolin impurities than by kaolin minerals themselves; (d) BET surfaces increase when kaolinite crystallinity decreases; (e) brightness is inversely correlated with kaolin impurities; (f) the more ordered the kaolinite and the greater the proportion in the <4 µm fraction of the kaolin, the greater the brightness; and (g) KCI values are particle size-distribution dependent for sedimentary-residual kaolins. The correlations obtained were better when kaolins were selected according to their origin because the kaolin minerals and their impurities, particle size-distribution and texture were more alike. The industrial properties of kaolin can not be predicted from other basic properties such as mineralogy, KCI, etc., because they are intricately related to one another.


2014 ◽  
Vol 937 ◽  
pp. 187-190
Author(s):  
Xue Bing Li ◽  
Wei Wang ◽  
Dong Hai Zhang ◽  
Li Xiong

A large amount of dust can be produced in iron and steel making process. This paper analysis the chemical composition, particle size distribution and microscopic characteristics of those iron and steel making dust. Some dust with high iron content, some dust with much CaO and some dust with carbon, those indicate that the iron and steel making dust can be used as iron making raw material. But the size of the iron and steel making dust is very small, which will make it harder to deal with those dust.


Sign in / Sign up

Export Citation Format

Share Document