The Effect of Fuel Injection Pressure on Spray and Combustion Characteristics in a Gasoline Direct-Injection Engine

2014 ◽  
Author(s):  
Mayank Mittal ◽  
Harold Schock
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Gasoline Direct Injection ◽  
Direct Injection Engine ◽  
Gasoline Direct Injection Engine ◽  
Fuel Injection Pressure

Combustion Characteristics of Methane Direct Injection Engine Under Various Injection Timings and Injection Pressures

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Jingeun Song ◽  
Mingi Choi ◽  
Daesik Kim ◽  
Sungwook Park
Keyword(s):  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Direct Injection Engine ◽  
Optical Engine ◽  
Start Of Injection ◽  
Crank Angle ◽  
Combustion Speed ◽  
Injection Pressures

The performance of a methane direct injection engine was investigated under various fuel injection timings and injection pressures. A single-cylinder optical engine was used to acquire in-cylinder pressure data and flame images. An outward-opening injector was installed at the center of the cylinder head. Experimental results showed that the combustion characteristics were strongly influenced by the end of injection (EOI) timing rather than the start of injection (SOI) timing. Late injection enhanced the combustion speed because the short duration between the end of injection and the spark-induced strong turbulence. The flame propagation speeds under various injection timings were directly compared using crank-angle-resolved sequential flame images. The injection pressure was not an important factor in the combustion; the three injection pressure cases of 0.5, 0.8, and 1.1 MPa yielded similar combustion trends. In the cases of late injection, the injection timings of which were near the intake valve closing (IVC) timing, the volumetric efficiency was higher (by 4%) than in the earlier injection cases. This result implies that the methane direct injection engine can achieve higher torque by means of the late injection strategy.

scholarly journals Particulate emissions from a highly boosted gasoline direct injection engine

2017 ◽  
Vol 19 (3) ◽  
pp. 347-359 ◽  
Author(s):  
Felix Leach ◽  
Richard Stone ◽  
Dave Richardson ◽  
Andrew Lewis ◽  
Sam Akehurst ◽  
...  
Keyword(s):  
Particle Number ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Back Pressure ◽  
Gasoline Direct Injection ◽  
Exhaust Gas ◽  
Fuel Injection Pressure ◽  
Gas Recirculation ◽  
Operating Points

Downsized, highly boosted, gasoline direct injection engines are becoming the preferred gasoline engine technology to ensure that increasingly stringent fuel economy and emissions legislation are met. The Ultraboost project engine is a 2.0-L in-line four-cylinder prototype engine, designed to have the same performance as a 5.0-L V8 naturally aspirated engine but with reduced fuel consumption. It is important to examine particle number emissions from such extremely highly boosted engines to ensure that they are capable of meeting current and future emissions legislation. The effect of such high boosting on particle number emissions is reported in this article for a variety of operating points and engine operating parameters. The effect of engine load, air–fuel ratio, fuel injection pressure, fuel injection timing, ignition timing, inlet air temperature, exhaust gas recirculation level, and exhaust back pressure has been investigated. It is shown that particle number emissions increase with increase in cooled, external exhaust gas recirculation and engine load, and decrease with increase in fuel injection pressure and inlet air temperature. Particle number emissions are shown to fall with increased exhaust back pressure, a key parameter for highly boosted engines. The effects of these parameters on the particle size distributions from the engine have also been evaluated. Significant changes to the particle size spectrum emitted from the engine are seen depending on the engine operating point. Operating points with a bias towards very small particle sizes were noted.

Sign in / Sign up

Export Citation Format

Share Document