Estimating the optical extinction of liquid water clouds in the cloud base region

Abstract. Accurate lidar-based measurements of cloud optical extinction, even though perhaps limited to the cloud base region, are useful. Arguably, more advanced lidar techniques (e.g. Raman) should be applied for this purpose. However, simpler polarisation and backscatter lidars offer a number of practical advantages (e.g. better resolution and more continuous and numerous time series). In this paper, we present a backscatter lidar signal inversion method for the retrieval of the cloud optical extinction in the cloud base region. Though a numerically stable method for inverting lidar signals using a far-end boundary value solution has been demonstrated earlier and may be considered as being well established (i.e. the Klett inversion), the application to high-extinction clouds remains problematic. This is due to the inhomogeneous nature of real clouds, the finite range resolution of many practical lidar systems, and multiple scattering effects. We use an inversion scheme, where a backscatter lidar signal is inverted based on the estimated value of cloud extinction at the far end of the cloud, and apply a correction for multiple scattering within the cloud and a range resolution correction. By applying our technique to the inversion of synthetic lidar data, we show that, for a retrieval of up to 90 m from the cloud base, it is possible to obtain the cloud optical extinction within the cloud with an error better than 5 %. In relative terms, the accuracy of the method is smaller at the cloud base but improves with the range within the cloud until 45 m and deteriorates slightly until reaching 90 m from the cloud base.

Download Full-text

Estimating optical extinction of liquid water clouds in the cloud base region

10.5194/amt-2020-504 ◽

2021 ◽

Author(s):

Karolina Sarna ◽

David P. Donovan ◽

Herman W. J. Russchenberg

Keyword(s):

Multiple Scattering ◽

Cloud Base ◽

Inversion Method ◽

Lidar Signal ◽

Base Region ◽

Optical Extinction ◽

Range Resolution ◽

Scattering Effects ◽

Numerous Time ◽

Better Than

Abstract. Accurate lidar-based measurements of cloud optical extinction, even though perhaps limited to the cloud base region, are useful. Arguably, more advanced lidar techniques (e.g. Raman) should be applied for this purpose. However, simpler polarization and backscatter lidars offer a number of practical advantages (e.g. better resolution, more continuous and numerous time series). In this paper we present a backscatter lidar signal inversion method for the retrieval of the cloud optical extinction in the cloud base region. Though a numerically stable method for inverting lidar signals using a far-end boundary value solution has been earlier demonstrated and may be considered well-established (i.e. the Klett inversion), the application to high-extinction clouds remains problematic. This is due to the inhomogeneous nature of real clouds, the finite range-resolution of many practical lidar systems and multiple-scattering effects. We use an inversion scheme where a backscatter lidar signal is inverted based on the estimated value of cloud extinction at the far end of the cloud and apply a correction for multiple-scattering within the cloud and a range resolution correction. By applying our technique to the inversion of synthetic lidar data, we show that for a retrieval of up to 90 m from the cloud base it is possible to obtain the cloud optical extinction within the cloud with an error better than 5 %. In relative terms, the accuracy of the method is smaller at the cloud base but improves with the range within the cloud until 45 m and deteriorates slightly until reaching 90 m from the cloud base.

Download Full-text

A depolarisation lidar based method for the determination of liquid-cloud microphysical properties

Atmospheric Measurement Techniques Discussions ◽

10.5194/amtd-7-9917-2014 ◽

2014 ◽

Vol 7 (9) ◽

pp. 9917-9992 ◽

Cited By ~ 1

Author(s):

D. P. Donovan ◽

H. Klein Baltink ◽

J. S. Henzing ◽

S. R. de Roode ◽

A. P. Siebesma

Keyword(s):

Water Content ◽

Multiple Scattering ◽

Liquid Water ◽

Cloud Droplet ◽

Optimal Estimation ◽

Liquid Water Content ◽

Cloud Base ◽

Base Region ◽

Large Eddy Simulation Model ◽

Inversion Procedure

Abstract. The fact that polarisation lidars measure a depolarisation signal in liquid clouds due to the occurrence of multiple-scattering is well-known. The degree of measured depolarisation depends on the lidar characteristics (e.g. wavelength and receiver field-of-view) as well as the cloud macrophysical (e.g. liquid water content) and microphysical (e.g. effective radius) properties. Efforts seeking to use depolarisation information in a quantitative manner to retrieve cloud properties have been undertaken with, arguably, limited practical success. In this work we present a retrieval procedure applicable to clouds with (quasi-)linear liquid water content (LWC) profiles and (quasi-)constant cloud droplet number density in the cloud base region. Thus limiting the applicability of the procedure allows us to reduce the cloud variables to two parameters (namely the derivative of the liquid water content with height and the extinction at a fixed distance above cloud-base). This simplification, in turn, allows us to employ a fast and robust optimal-estimation inversion using pre-computed look-up-tables produced using extensive lidar Monte-Carlo multiple-scattering simulations. In this paper, we describe the theory behind the inversion procedure and successfully apply it to simulated observations based on large-eddy simulation model output. The inversion procedure is then applied to actual depolarisation lidar data corresponding to a range of cases taken from the Cabauw measurement site in the central Netherlands. The lidar results were then used to predict the corresponding cloud-base region radar reflectivities. In non-drizzling condition, it was found that the lidar inversion results can be used to predict the observed radar reflectivities with an accuracy within the radar calibration uncertainty (2–3 dBZ). This result strongly supports the accuracy of the lidar inversion results. Results of a comparison between ground-based aerosol number concentration and lidar-derived cloud droplet number densities are also presented and discussed. The observed relationship between the two quantities is seen to be consistent with the results of previous studies based on aircraft-based in situ measurements.

Download Full-text

A depolarisation lidar-based method for the determination of liquid-cloud microphysical properties

Atmospheric Measurement Techniques ◽

10.5194/amt-8-237-2015 ◽

2015 ◽

Vol 8 (1) ◽

pp. 237-266 ◽

Cited By ~ 23

Author(s):

D. P. Donovan ◽

H. Klein Baltink ◽

J. S. Henzing ◽

S. R. de Roode ◽

A. P. Siebesma

Keyword(s):

Water Content ◽

Multiple Scattering ◽

Liquid Water ◽

Cloud Droplet ◽

Optimal Estimation ◽

Liquid Water Content ◽

Cloud Base ◽

Base Region ◽

Microphysical Properties ◽

Inversion Procedure

Abstract. The fact that polarisation lidars measure a depolarisation signal in liquid clouds due to the occurrence of multiple scattering is well known. The degree of measured depolarisation depends on the lidar characteristics (e.g. wavelength and receiver field of view) as well as the cloud macrophysical (e.g. cloud-base altitude) and microphysical (e.g. effective radius, liquid water content) properties. Efforts seeking to use depolarisation information in a quantitative manner to retrieve cloud properties have been undertaken with, arguably, limited practical success. In this work we present a retrieval procedure applicable to clouds with (quasi-)linear liquid water content (LWC) profiles and (quasi-)constant cloud-droplet number density in the cloud-base region. Thus limiting the applicability of the procedure allows us to reduce the cloud variables to two parameters (namely the derivative of the liquid water content with height and the extinction at a fixed distance above cloud base). This simplification, in turn, allows us to employ a fast and robust optimal-estimation inversion using pre-computed look-up tables produced using extensive lidar Monte Carlo (MC) multiple-scattering simulations. In this paper, we describe the theory behind the inversion procedure and successfully apply it to simulated observations based on large-eddy simulation (LES) model output. The inversion procedure is then applied to actual depolarisation lidar data corresponding to a range of cases taken from the Cabauw measurement site in the central Netherlands. The lidar results were then used to predict the corresponding cloud-base region radar reflectivities. In non-drizzling condition, it was found that the lidar inversion results can be used to predict the observed radar reflectivities with an accuracy within the radar calibration uncertainty (2–3 dBZ). This result strongly supports the accuracy of the lidar inversion results. Results of a comparison between ground-based aerosol number concentration and lidar-derived cloud-droplet number densities are also presented and discussed. The observed relationship between the two quantities is seen to be consistent with the results of previous studies based on aircraft-based in situ measurements.

Download Full-text