Improvement of Film Cooling Performance of a Slot on a Flat Plate Using Coanda Effect

2017 ◽  
Vol 20 (2) ◽  
pp. 5-10 ◽  
Author(s):  
Gi Mun Kim ◽  
Ye Jee Kim ◽  
Jae Su Kwak
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Coanda Effect ◽  
Cooling Performance ◽  
Coandǎ Effect

Numerical modeling of innovative film cooling hole schemes

2021 ◽  
Author(s):  
Siavash Khajehhasani
Keyword(s):  
Flat Plate ◽  
Turbine Blade ◽  
Film Cooling ◽  
Leading Edge ◽  
Lateral Spread ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Mainstream Flow ◽  
Hole Geometry

A numerical investigation of the film cooling performance on novel film hole schemes is presented using Reynolds-Averaged Navier-Stokes analysis. The investigation considers low and high blowing ratios for both flat plate film cooling and the leading edge of a turbine blade. A novel film hole geometry using a circular exit shaped hole is proposed, and the influence of an existing sister holes’ technique is investigated. The results indicate that high film cooling effectiveness is achieved at higher blowing ratios, results of which are even greater when in the presence of discrete sister holes where film cooling effectiveness results reach a plateau. Furthermore, a decrease in the strength of the counter-rotating vortex pairs is evident, which results in more attached coolant to the plate’s surface and a reduction in aerodynamic losses. Modifications are made to the spanwise and streamwise locations of the sister holes around the conventional cylindrical hole geometry. It is found that the spanwise variations have a significant influence on the film cooling effectiveness results, while only minor effects are observed for the streamwise variations. Positioning the sister holes in locations farther from the centerline increases the lateral spreading of the coolant air over the plate’s surface. This result is further verified through the flow structure analysis. Combinations of sister holes are joined with the primary injection hole to produce innovative variant sister shaped single-holes. The jet lift-off is significantly decreased for the downstream and up/downstream configurations of the proposed scheme for the flat plate film cooling. These schemes have shown notable film cooling improvements whereby more lateral distribution of coolant is obtained and less penetration of coolant into the mainstream flow is observed. The performance of the sister shaped single-holes are evaluated at the leading edge of a turbine blade. At the higher blowing ratios, a noticeable improvement in film cooling performance including the effectiveness and the lateral spread of the cooling air jet has been observed for the upstream and up/downstream schemes, in particular on the suction side. It is determined that the mixing of the coolant with the high mainstream flow at the leading edge of the blade is considerably decreased for the upstream and up/downstream configurations and more adhered coolant to the blade’s surface is achieved.

scholarly journals Flat Plate and Turbine Vane Film-Cooling Performance with Laid-Back Fan-Shaped Holes

2019 ◽  
Vol 4 (2) ◽  
pp. 14 ◽  
Author(s):  
Tommaso Bacci ◽  
Alessio Picchi ◽  
Bruno Facchini
Keyword(s):  
Flat Plate ◽  
Film Cooling ◽  
Density Ratio ◽  
Pressure Sensitive Paint ◽  
Cooling Performance ◽  
Blowing Ratio ◽  
Pressure Sensitive ◽  
Turbine Vane ◽  
Experimental Works ◽  
Lift Off

Shaped holes are considered as an effective solution to enhance gas turbine film-cooling performance, as they allow to increase the coolant mass-flux, while limiting the detrimental lift-off phenomena. A great amount of work has been carried out in past years on basic flat plate configurations while a reduced number of experimental works deals with a quantitative assessment of the influence of curvature and vane pressure gradient. In the present work PSP (Pressure Sensitive Paint) technique is used to detail the adiabatic effectiveness generated by axial shaped holes with high value of Area Ratio close to 7, in three different configurations with the same 1:1 scale: first of all, a flat plate configuration is examined; after that, the film-cooled pressure and suction sides of a turbine vane model are investigated. Tests were performed varying the blowing ratio and imposing a density ratio of 2.5 . The experimental results are finally compared to the predictions of two different correlations, developed for flat plate configurations.

Exploring Conjugate CFD Heat Transfer Characteristics for a Film-Cooled Flat Plate and 3-D Turbine Inlet Vane

2012 ◽  
Author(s):  
J. J. Johnson ◽  
P. I. King ◽  
J. P. Clark ◽  
P. J. Koch
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Film Cooling ◽  
Low Cost ◽  
Full Scale ◽  
Design Flow ◽  
Navier Stokes ◽  
Cooling Performance ◽  
Cooling Design ◽  
Computational Fluid Dynamics Cfd

As part of a thorough benchmarking of the baseline cooling design in planned optimization work, Reynolds-Averaged Navier Stokes (RANS) conjugate heat transfer (CHT) computational fluid dynamics (CFD) assessments have been accomplished at RTV design flow conditions to simulate both a cooled flat plate pressure side (PS) model infrared thermography experiment as well as a full-scale, fully-cooled, full-wheel blowdown experiment on the same high pressure turbine (HPT) vane. Numerous past works on turbomachinery film cooling have been conducted using flat plate models because of their simplicity, repeatability, and low cost of experimentation relative to full scale rotating blowdown rigs. Some of these works generated film cooling correlations still in use today in industry for HPT components. The CFD assessments in this work provide insight into the fundamental differences between a flat plate model and a realistic 3-D vane in terms of film cooling performance for the same PS cooling array. The comparisons of results wring out expected differences between the geometries due to aspects such as highly curved surfaces and endwall effects. However, with nearly-matched coolant-to-mainstream temperature and pressure ratios, the cooling performance between the two models is surprisingly similar, especially in the midspan region. The similarities and differences observed herein represent the rigor and accuracy afforded by simulating both the solid and fluid domains as well as the high-density unstructured meshes that take into account all individual cooling passages and internal plenums, on top of the typically-assessed external fluid flow field.

Numerical Approach at Flat Plate for Predicting the Film Cooling Effectiveness Part A: Effect Blowing Ratio

2018 ◽  
Vol 16 ◽  
pp. 30-44 ◽  
Author(s):  
Farouk Kebir ◽  
Azzeddine Khorsi
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Film Cooling ◽  
Thermal Stresses ◽  
Free Stream ◽  
Turbine Blades ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Free Stream Turbulence ◽  
Blowing Ratio

Film cooling is vital for gas turbine blades to protect them from thermal stresses and high temperatures due to the hot gas flow in the blade surface. Film cooling is applied to almost all external surfaces associated with aerodynamic profiles that are exposed to hot combustion gases such as main bodies, end-walls, blade tips and leading edges. In a review of the literature, it was found that there are strong effects of free-stream turbulence, surface curvature and hole shape on film cooling performance also blowing ratio. The performance of the film cooling is difficult to predict due to the inherent complex flow fields along the surfaces of the airfoil components in the turbine engines. From all what we introducing the film cooling is reviewed through a discussion of the analyses methodologies, a physical description, and the various influences on film-cooling performance. Initially Computational analysis was done on a flat plate with hole inclined at 55° to the surface plate. This study focuses on the efficient computation of film cooling flows with three blowing ratio. The numerical results show the effectiveness cooling and heat transfer behavior with increasing injection blowing ratio M (0.5, 1, and 1.5). The influence of increased blade film cooling can be assessed via the values of Nusselt number in terms of reduced heat transfer to the blade. Predictions of film effectiveness are compared with experimental results for a circular jet at blowing ratios ranging from 0.5, 1.0 and 1.5. The present results are obtained at a free stream turbulence of 10%, which are the typical conditions upstream of the effectiveness is generally lower for a large stream-wise angle of 55°.

Surface Curvature Effects on Film Cooling Performance for Shaped Holes on a Model Turbine Blade

2020 ◽  
Vol 142 (11) ◽  
Author(s):  
Jacob D. Moore ◽  
Christopher Yoon ◽  
David G. Bogard
Keyword(s):  
Flat Plate ◽  
Turbine Blade ◽  
Film Cooling ◽  
Gas Turbines ◽  
Convex Surface ◽  
Adverse Pressure Gradient ◽  
Suction Side ◽  
Surface Curvature ◽  
Cooling Performance ◽  
Curvature Effects

Abstract Surface curvature has been shown to have significant effects on the film cooling performance of round holes, but the literature include few studies of its effects on shaped holes despite their prevalence in gas turbines. Experiments were performed using two rows of holes placed on the suction side of a scaled-up turbine blade in a low Mach number linear cascade wind tunnel with low freestream turbulence. The rows were placed in regions of high and low convex surface curvature. Geometries and flow conditions for the rows were matched to those from previous flat plate studies. Comparison of the adiabatic effectiveness results from the high curvature and flat plate rows revealed the same trends as those in the literature using round holes, with increased performance for the high curvature row at lower blowing ratios and the opposite at higher ones. The low curvature row had similar performance to the flat plate row at lower blowing ratios, suggesting the mild convex curvature had little beneficial effect. At higher blowing ratios, the low curvature row had inferior performance, which was attributed to the local freestream adverse pressure gradient that generated additional turbulence, promoting jet-to-mainstream mixing and decreasing performance.

An Experimental Investigation of an Anti-Vortex Film Cooling Geometry Under Low and High Turbulence Conditions

2012 ◽  
Author(s):  
Sebastian Schulz ◽  
Simon Maier ◽  
Jeffrey P. Bons
Keyword(s):  
Flat Plate ◽  
Secondary Flow ◽  
Infrared Thermography ◽  
Film Cooling ◽  
Streamwise Direction ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Cooling Hole ◽  
High Turbulence

In an attempt to abate the detrimental jet vorticity and lift-off effects at high blowing ratios, the objective of the present study is to investigate the impact of an anti-vortex film cooling hole design on the film cooling effectiveness and the secondary flow field. Furthermore, the influence of low and high turbulence levels is studied with Tu ≈ .0.7% and ≈ 10%, respectively. For the experiments infrared thermography and particle image velocimetry (PIV) are employed. The experiments are conducted in a subsonic wind tunnel at a Reynolds number of 11000 based on the film cooling hole diameter. A flat plate model with an array of three cylindrical primary holes with secondary offshoots to each side represents the anti-vortex geometry. The cylindrical hole arrangement with a diameter of 17.5 mm is inclined at 30° in streamwise direction, with the anti-vortex holes branching off from the primary hole base in a 21° angle. Information from a flat plate with six cylindrical holes of 17.5 mm in diameter inclined at 30 in streamwise direction is used as baseline for comparison. The primary hole spacing was 4.75 and 3 hole diameters, respectively. Results are presented for blowing ratios of 1 and 2 with a constant density ratio of 1.1. The PIV measurements are taken in two planes perpendicular to the flow direction to record the secondary flow structures. The results of the infrared thermography show a strong decrease in film cooling effectiveness as high turbulence levels occur, especially for low blowing ratios. For higher blowing ratios low and high turbulence levels have similar effects on film cooling effectiveness. A significant improvement in film cooling performance is displayed by the anti-vortex design over the standard circular hole arrangement for every blowing ratio. The effectiveness results reveal an improved lateral spreading of the coolant with coolant jets staying attached throughout the series of experiments. By remaining inside the boundary layer, the effects of a high turbulent freestream on film cooling performance is less. The PIV results unveil information of a new vortex pair on either side of the primary hole kidney vortex. Especially at high blowing ratios the results indicate, that the anti-vortex hole design promotes the interaction between the vortical structures, explaining the increased lateral film effectiveness results. The factor which lends to the superior performance and credibility of the studied anti-vortex design is that the results are obtained for 35% less mass flow than the baseline.

Experimental and Numerical Study on Effects of Turbulence Promoters on Flat Plate Film Cooling

2011 ◽  
Author(s):  
Eiji Sakai ◽  
Toshihiko Takahashi
Keyword(s):  
Flat Plate ◽  
Secondary Flow ◽  
Film Cooling ◽  
Numerical Study ◽  
Secondary Flows ◽  
Temperature Fields ◽  
Main Stream ◽  
Cooling Performance ◽  
Cooling Hole ◽  
Stream Lines

Turbulence promoters such as ribs inside turbine blade coolant channels are used to improve convective cooling but at the same time could influence external film cooling performance. The effects of rib orientation and rib position on film cooling performance are experimentally and numerically studied with a flat plate configuration in which external (main) flow and internal (secondary) flow are oriented perpendicular to each other. In the experiment, temperature fields are measured by thermo-couples varying blowing ratio at constant Reynolds number of main and secondary flows. To obtain detailed information about flow fields, Reynolds Averaged Navier Stokes (RANS) simulation and Detached Eddy Simulation (DES) are also performed using a commercial code Fluent. Temperature measured shows that rib orientation has a strong influence on film effectiveness. With forward-oriented ribs, higher film effectiveness is observed compared to the reference case without ribs. On the contrary with inverse-oriented ribs, lower film effectiveness is observed. The difference comes from the flow structure in the film cooling hole. With the forward-oriented ribs, straight stream lines are observed in the cooling hole, while with the inverse-oriented ribs, helical stream lines are observed. Due to the helical stream lines in the hole, ejection angle of the secondary flow to the main stream becomes large, resulting in so called lift-off and lower film effectiveness.

Improvement of Flat-Plate Film Cooling Performance by Double Flow Control Devices: Part I — Investigations on Capability of a Base-Type Device

2014 ◽  
Author(s):  
Ken-ichi Funazaki ◽  
Ryota Nakata ◽  
Hirokazu Kawabata ◽  
Hisato Tagawa ◽  
Yasuhiro Horiuchi
Keyword(s):  
Flow Control ◽  
Flat Plate ◽  
Film Cooling ◽  
Laser Doppler Velocimeter ◽  
Pressure Probe ◽  
Cooling Performance ◽  
Flow Control Devices ◽  
Type Device ◽  
Cooling Hole ◽  
Control Devices

This paper deals with effects of double flow control devices (DFCDs) on flat plate film cooling performance. Aiming for further improvement of film effectiveness of discrete cooling holes, this new type of controlling method is invented and recently patented by the authors. The performance of base-type DFCDs, installed just upstream of cooling holes with conventional round or fan-shaped exits, is thoroughly investigated and reported in this study. Effects of the hole pitch are examined. Three hole-pitch cases, 3.0d, 4.5 d and 6.0 d are examined in this study to explore a possibility of reducing the cooling air by the application of DFCDs, where d is a hole diameter. In order to investigate the film effectiveness, a transient method using a high-resolution infrared camera is adopted. At the downstream of the cooling hole, the time-averaged temperature field is captured by a thermocouple rake and the time-averaged velocity field is captured by 3D Laser Doppler Velocimeter (LDV), respectively. Furthermore, the aerodynamic loss characteristics of the cooling hole with and without DFCDs are measured by a total pressure probe rake. The experiments are carried out for two blowing ratios, 0.5 and 1.0. It is found that DFCDs are quite effective in increasing the film effectiveness not only for round but also the fan-shaped holes. Starting from the base-type device, a robust optimization using Taguchi Method has been made by the present authors and will be reported as Part II.

Sign in / Sign up

Export Citation Format

Share Document