Evaluation of Superposition Predictions for Showerhead Film Cooling on a Vane

The leading edge of a turbine vane is subject to some of the highest temperature loading within an engine, and an accurate understanding of leading edge film coolant behavior is essential for modern engine design. Although there have been many investigations of the adiabatic effectiveness for showerhead film cooling of a vane leading edge region, there have been no previous studies in which individual rows of the showerhead were tested with the explicit intent of validating superposition models. For the current investigation, a series of adiabatic effectiveness experiments were performed with a five-row and three-row showerhead. The experiments were repeated separately with each individual row of holes active. This allowed evaluation of superposition methods on both the suction side of the vane, which was moderately convex, and the pressure side of the vane, which was mildly concave. Superposition was found to accurately predict performance on the suction side of the vane at lower momentum flux ratios, but not at higher momentum flux ratios. On the pressure side of the vane the superposition predictions were consistently lower than measured values, with significant errors occurring at the higher momentum flux ratios. Reasons for the under-prediction by superposition analysis are presented.

The Effect of Internal Cross-Flow on the Adiabatic Effectiveness of Compound Angle Film Cooling Holes

In gas turbine engines, film cooling holes are often fed by an internal cross-flow, with flow normal to the direction of the external flow around the airfoil. Many experimental studies have used a quiescent plenum to feed model film cooling holes and thus do not account for the effects of internal cross-flow. In this study, an experimental flat plate facility was constructed to study the effects of internal cross-flow on a row of cylindrical compound angle film cooling holes. Operating conditions were scaled, based on coolant hole Reynolds number and turbulence level, to match realistic turbine engine conditions. A cross-flow channel allowed for coolant to flow alternately in either direction perpendicular to the mainstream flow. Film cooling holes were operated at blowing ratios ranging from 0.5 to 2.0 at a density ratio of 1.5. There are relatively few studies available in literature that focus on the effects of cross-flow on film cooling performance, with no studies examining the effects of internal cross-flow on film cooling with round, compound angled holes. This study showed that significantly greater adiabatic effectiveness was achieved for cross-flow in the opposite direction of the span-wise direction of the coolant holes and provides possible explanations for this result.

An Experimental Study of Heat Transfer on an Outlet Guide Vane

In the present study, the heat transfer characteristics on the suction and pressure sides of an outlet guide vane (OGV) are investigated by using liquid crystal thermography (LCT) method in a linear cascade. Because the OGV has a complex curved surface, it is necessary to calibrate the LCT by taking into account the effect of viewing angles of the camera. Based on the calibration results, heat transfer measurements of the OGV were conducted. Both on- and off-design conditions were tested, where the incidence angles of the OGV were 25 degrees and −25 degrees, respectively. The Reynolds numbers, based on the axial flow velocity and the chord length, were 300,000 and 450,000. In addition, heat transfer on suction side of the OGV with +40 degrees incidence angle was measured. The results indicate that the Reynolds number and incidence angle have considerable influences upon the heat transfer on both pressure and suction surfaces. For on-design conditions, laminar-turbulent boundary layer transitions are on both sides, but no flow separation occurs; on the contrary, for off-design conditions, the position of laminar-turbulent boundary layer transition is significantly displaced downstream on the suction surface, and a separation occurs from the leading edge on the pressure surface. As expected, larger Reynolds number gives higher heat transfer coefficients on both sides of the OGV.

Film Cooling From Novel Sister Shaped Single-Holes

A numerical investigation of the film cooling performance from novel sister shaped single-holes (SSSH) is presented in this paper and the obtained results are compared with a single cylindrical hole, a forward diffused shaped hole, as well as discrete sister holes. Three types of the novel sister shaped single-hole schemes namely downstream, upstream and up/downstream SSSH, are designed based on merging the discrete sister holes to the primary hole in order to reduce the jet lift-off effect and increase the lateral spreading of the coolant on the blade surface as well as a reduction in the amount of coolant in comparison with discrete sister holes. The simulations are performed using three-dimensional Reynolds-Averaged Navier Stokes analysis with the realizable k–ε model combined with the standard wall function. The upstream SSSH demonstrates similar film cooling performance to that of the forward diffused shaped hole for the low blowing ratio of 0.5. While it performs more efficiently at M = 1, where the centerline and laterally averaged effectiveness results improved by 70% and 17%, respectively. On the other hand, the downstream and up/downstream SSSH schemes show a considerable improvement in film cooling performance in terms of obtaining higher film cooling effectiveness and less jet lift-off effect as compared with the single cylindrical and forward diffused shaped holes for both blowing ratios of M = 0.5 and 1. For example, the laterally averaged effectiveness for the downstream SSSH configuration shows an improvement of approximately 57% and 110% on average as compared to the forward diffused shaped hole for blowing ratios of 0.5 and 1, respectively.

A CFD-Based Parametric Study on Modification of Discrete Sister Holes Location for the Film Cooling Flow

A numerical study on the effects of sister holes locations on film cooling performance is presented. This includes the change of the location of the individual discrete sister holes in the streamwise and spanwise directions, where each one of these directions includes 9 different locations, The simulations are performed using three-dimensional Reynolds-Averaged Navier Stokes analysis with the realizable k–ε model combined with the standard wall function. The variation of the sister holes in the streamwise direction provides similar film cooling performance as the base case for both blowing ratios of 0.5 and 1. On the other hand, the spanwise variation of the sister holes’ location has a more prominent effect on the effectiveness. In some cases, as a result of the anti-vortices generated from the sister holes and the repositioning of the sister holes in the spanwise direction, the jet lift-off effect notably decreases and more volume of coolant is distributed in the spanwise direction.

LES and Hybrid RANS/LES of a Fundamental Trailing Edge Slot

This paper presents the results of a numerical study on the predictive capabilities of Large Eddy Simulation (LES) and hybrid RANS/LES methods for heat transfer, mean velocity, and turbulence in a fundamental trailing edge slot. The geometry represents a landless slot (two-dimensional wall jet) with adjustable slot lip thickness. The reference experimental data taken from the publications of Kacker and Whitelaw [1] [2] [3] [4] contains the adiabatic wall effectiveness together with the velocity and the Reynolds-stress profiles for various blowing ratios and slot lip thicknesses. The simulations were conducted at three different lip thickness and several blowing ratio values. The comparison with the experimental data shows a general advantage of LES and hybrid RANS/LES methods against unsteady RANS. The predictive capability of the tested LES models (dynamic ksgs-equation [5] and WALE [6]) was comparable. The Improved Delayed Detached Eddy Simulation (IDDES) hybrid method [7] also shows satisfactory agreement with the experimental data. In addition to the described baseline investigations, the influence of the inlet turbulence boundary conditions and their implication for the initial mixing layer and heat transfer development were studied for both LES and IDDES.

Large-Scale Simulation of the Clocking Impact of 2D Combustor Profile on a Two Stage High Pressure Turbine

This paper presents sliding-mesh unsteady CFD simulations of high-pressure turbine sections of a modern aviation engine in an extension of previously presented work [1]. The simulation included both the first and second stages of a two-stage high-pressure turbine. Half-wheel domains were used, with source terms representing purge and film flows. The end-wall flow-path cavities were incorporated in the domain to a limited extent. The passage-to-passage variation in thermal predictions was compared for a 1D and 2D turbine inlet boundary condition. Substantial impact was observed on both first and second stage vanes despite the mixing from the first stage blade. Qualitative and quantitative differences in surface temperature distributions were observed due to different ratios between airfoil counts in the two domains.

Effect of Radiative Heat Transfer Factor on the Temperature Distribution of a First Stage Vane

As the advanced heavy-duty gas turbine develops, the turbine inlet temperature and pressure have increased quite significantly to achieve better performance. The flow and heat transfer conditions of hot components including combustor and turbine become even more extreme than ever which need corresponding aerodynamic and cooling design development. The issue of combustor-turbine interaction has been proposed as a complicated research topic. Currently the hot streak, turbulence intensity, swirling flow, radiation are the four important factors for combustor-turbine interaction research according to the literature. Especially as the turbine inlet temperature increases, the radiative heat transfer plays a more and more important role. In this paper, a first stage vane is selected for the conjugate heat transfer simulation including radiative heat transfer since it is almost impossible to identify the radiative effect in experiment. The goal is to examine the effects of radiative heat flux and temperature increment caused by radiation. Several radiative factors including the inlet radiation, gas composition, vane surface emissivity and outlet reflection are investigated. The temperature distribution and heat flux enhancement under different conditions are compared, which can provide reference to the turbine heat transfer design. The general information of radiative effect can be summarized by quantitative analysis. Results show that the temperature increases obviously when considering the radiation effect as expected. However, these factors show distinct influence on the vane temperature distribution. The inlet radiation has significant impact on the vane leading edge and pressure side. Besides the gas radiation plays quite uniform on the whole vane surface.

Phantom Cooling of Nozzle Trailing Edge Discharge on Blade Surface and Platform

Phantom cooling is defined as the cooling redistribution on airfoil surfaces and endwalls due to airfoil cooling discharges and leakages. Understanding of this effect has become especially critical in recent years, because of the restricted amount of cooling air for the achievement of higher efficiency. The phantom cooling effect of the first stage nozzle trailing edge discharge on the first stage blade surfaces and platform are studied numerically with URANS. Both time-dependent and time-averaged cooling effectiveness distributions on the rotor under the influence of vane trailing edge discharge are presented with different discharge velocity ratios. The results show that the nozzle trailing edge ejection affects the suction and pressure side cooling of the blade as well as the platform. The effects on the triangular zones of suction surface are evident, especially the bottom and top zones which are better cooled. Under the influence of passage secondary flows and rotating, different coolant discharge velocity ratios which resulted in different inlet angles have an effect on the phantom cooling distribution. In general, the cooling air discharged from the trailing edge of the first stage nozzle influences the temperature distribution on the blade, which can substantially improve the cooling efficiency in the bottom triangular zone. This suggests that accounting for phantom cooling can improve the cooling design and if actively controlled save cooling flow.

Nekomimi Film Cooling Holes Configuration Under Conjugate Heat Transfer Conditions

In modern gas turbines, the film cooling technology is essential for the protection of the hot parts, in particular of the first stage vanes and blades of the turbine, against the hot gases from the combustion process in order to reach an acceptable life span of the components. As the cooling air is usually extracted from the compressor, the reduction of the cooling effort would directly result in increased thermal efficiency of the gas turbine. Understanding of the fundamental physics of film cooling is necessary for the improvement of the state-of-the-art. Thus, huge research efforts by industry as well as research organizations have been undertaken to establish high efficient film cooling technologies. Today it is common knowledge that film cooling effectiveness degradation is caused by secondary flows inside the cooling jets, i.e. the Counter-Rotating Vortices (CRV) or sometimes also called kidney-vortices, which induce a lift-off of the jet. Further understanding of the secondary flow development inside the jet and how this could be influenced, has led to hole configurations, which can induce Anti-Counter-Rotating Vortices (ACRV) in the cooling jets. As a result, the cooling air remains close to the wall and is additionally distributed flatly along the surface. Beside different other technologies, the NEKOMIMI cooling technology is a promising approach to establish the desired ACRVs. It consists of a combination of two holes in just one configuration so that the air is distributed mainly on two cooling air streaks following the special shape of the generated geometry. The NEKOMIMI configuration and two conventional cooling hole configurations (cylindrical and shaped holes) has been investigated numerically under adiabatic and conjugate heat transfer conditions. The influence of the conjugate heat transfer on the secondary flow structure has been analysed. In conjugate heat transfer calculations, it cannot directly derived from the surface temperature distribution if the reached cooling effectiveness values are due to the improved hole configuration with improved secondary flow structure or due to the heat conduction in the material. Therefore, a methodology has been developed, to distinguish between cooling effectiveness due to heat conduction in the material and film cooling flow over the surface. The numerical results shows that for the NEKOMIMI configuration, 77% of the reached overall cooling effectiveness is due to film cooling with improved flow structure in the secondary flow (ACRV) and 23% due to heat conduction in the material. For the cylindrical hole configuration, 10% of the reached overall cooling effectiveness is due to the film cooling flow structure and 90% due to heat conduction in the material.