scholarly journals ESTIMATION OF LOCAL LIQUID FILM THICKNESS IN TWO-PHASE ANNULAR FLOW

2012 ◽  
Vol 44 (1) ◽  
pp. 71-78 ◽  
Author(s):  
Bo-An Lee ◽  
Byong-Jo Yun ◽  
Kyung-Youn Kim ◽  
Sin Kim
Keyword(s):  
Film Thickness ◽  
Liquid Film ◽  
Annular Flow ◽  
Liquid Film Thickness ◽  
Two Phase

Measurement of Liquid Film Thickness in Micro Tube Annular Flow

2010 ◽  
Author(s):  
Hiroshi Kanno ◽  
Youngbae Han ◽  
Yusuke Saito ◽  
Naoki Shikazono
Keyword(s):  
Heat Transfer ◽  
Film Thickness ◽  
Liquid Film ◽  
Annular Flow ◽  
Liquid Film Thickness ◽  
Phase Flow ◽  
Two Phase ◽  
Micro Scale ◽  
Film Model ◽  
Annular Film

Heat transfer in micro scale two-phase flow attracts large attention since it can achieve large heat transfer area per density. At high quality, annular flow becomes one of the major flow regimes in micro two-phase flow. Heat is transferred by evaporation or condensation of the liquid film, which are the dominant mechanisms of micro scale heat transfer. Therefore, liquid film thickness is one of the most important parameters in modeling the phenomena. In macro tubes, large numbers of researches have been conducted to investigate the liquid film thickness. However, in micro tubes, quantitative information for the annular liquid film thickness is still limited. In the present study, annular liquid film thickness is measured using a confocal method, which is used in the previous study [1, 2]. Glass tubes with inner diameters of 0.3, 0.5 and 1.0 mm are used. Degassed water and FC40 are used as working fluids, and the total mass flux is varied from G = 100 to 500 kg/m2s. Liquid film thickness is measured by laser confocal displacement meter (LCDM), and the liquid-gas interface profile is observed by a high-speed camera. Mean liquid film thickness is then plotted against quality for different flow rates and tube diameters. Mean thickness data is compared with the smooth annular film model of Revellin et al. [3]. Annular film model predictions overestimated the experimental values especially at low quality. It is considered that this overestimation is attributed to the disturbances caused by the interface ripples.

scholarly journals MODELLING AIR AND WATER TWO-PHASE ANNULAR FLOW IN A SMALL HORIZONTAL PIPE

2016 ◽  
Vol 42 ◽  
pp. 1660158 ◽  
Author(s):  
JUN YAO ◽  
YUFENG YAO ◽  
ANTONINO ARINI ◽  
STUART MCIIWAIN ◽  
TIMOTHY GORDON
Keyword(s):  
Experimental Data ◽  
Film Thickness ◽  
Liquid Film ◽  
Annular Flow ◽  
Cfd Simulation ◽  
Two Phase Flow ◽  
Liquid Film Thickness ◽  
Phase Flow ◽  
Two Phase ◽  
Horizontal Pipe

Numerical simulation using computational fluid dynamics (CFD) has been carried out to study air and water two-phase flow in a small horizontal pipe of an inner diameter of 8.8mm, in order to investigate unsteady flow pattern transition behaviours and underlying physical mechanisms. The surface liquid film thickness distributions, determined by either wavy or full annular flow regime, are shown in reasonable good agreement with available experimental data. It was demonstrated that CFD simulation was able to predict wavy flow structures accurately using two-phase flow sub-models embedded in ANSYS-Fluent solver of Eulerian–Eulerian framework, together with a user defined function subroutine ANWAVER-UDF. The flow transient behaviours from bubbly to annular flow patterns and the liquid film distributions revealed the presence of gas/liquid interferences between air and water film interface. An increase of upper wall liquid film thickness along the pipe was observed for both wavy annular and full annular scenarios. It was found that the liquid wavy front can be further broken down to form the water moisture with liquid droplets penetrating upwards. There are discrepancies between CFD predictions and experimental data on the liquid film thickness determined at the bottom and the upper wall surfaces, and the obtained modelling information can be used to assist further 3D user defined function subroutine development, especially when CFD simulation becomes much more expense to model full 3D two-phase flow transient performance from a wavy annular to a fully developed annular type.

Measurement of Liquid Film Thickness for Annular Two-Phase HFC134a Gas-Liquid Ethanol Flow in the Vertical Tube

2021 ◽  
Author(s):  
Huacheng Zhang ◽  
Tutomo Hisano ◽  
Shoji Mori ◽  
Hiroyuki Yoshida
Keyword(s):  
Film Thickness ◽  
Liquid Film ◽  
Thin Liquid Film ◽  
Atmospheric Condition ◽  
Heating Surface ◽  
Operating Conditions ◽  
Liquid Film Thickness ◽  
Two Phase ◽  
Disturbance Waves ◽  
Analytical Approaches

Abstract Annular gas-liquid two-phase flows, such as the flows attached to the fuel rods of boiling water reactors (BWR), are a prevalent occurrence in industrial processes. At the gas-liquid interface of such flows, disturbance waves with diverse velocity and amplitude commonly arise. Since the thin liquid film between two successive disturbance waves leads to the dryout on the heating surface and limits the performance of the BWRs, complete knowledge of the disturbance waves is of great importance for the characterized properties of disturbance waves. The properties of disturbance waves have been studied by numerous researchers through extensive experimental and analytical approaches. However, most of the experimental data and analyses available in the literature are limited to the near atmospheric condition. In consideration of the properties of liquids and gases under atmospheric pressure which are distinct from those under BWR operating conditions (7 MPa, 285 °C), we employed the HFC134a gas and liquid ethanol whose properties at relatively low pressure and temperature (0.7 MPa, 40 °C) are similar to those of steam and water under BWR operating conditions as working fluids in a tubular test section having an inside diameter 5.0mm. Meanwhile, the liquid film thickness is measured by conductance probes. In this study, we report the liquid film thickness characteristics in a two-phase HFC134a gas-liquid ethanol flow. A simple model of the height of a disturbance wave was also proposed.

scholarly journals ANALYSIS OF INTERFACIAL AND MASS TRANSFER EFFECTS ON FORCED CONVECTION IN GAS-LIQUID ANNULAR TWO-PHASE FLOW

2004 ◽  
Vol 3 (1) ◽  
pp. 45
Author(s):  
E. Nogueira ◽  
B. D. Dantas ◽  
R. M. Cotta
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Film Thickness ◽  
Liquid Film ◽  
Liquid Film Thickness ◽  
Phase Flow ◽  
Transfer Effects ◽  
Two Phase ◽  
Transfer Rates ◽  
Interface Waves

In a gas-liquid annular two-phase flow one of the main factors influencing the determination of heat transfer rates is the average thickness of the liquid film. A model to accurately represent the heat transfer in such situations has to be able of determining the average liquid film thickness to within a reasonable accuracy. A typical physical aspect in gas-liquid annular flows is the appearance of interface waves, which affect heat, mass and momentum transfers. Existing models implicitly consider the wave effects in the momentum transfer by an empirical correlation for the interfacial friction factor. However, this procedure does not point out the difference between interface waves and the natural turbulent effects of the system. In the present work, the wave and mass transfer effects in the theoretical estimation of average liquid film thickness are analyzed, in comparison to a model that does not explicitly include these effects, as applied to the prediction of heat transfer rates in a thermally developing flow situation.

Sign in / Sign up

Export Citation Format

Share Document