INTERNAL COMBUSTION ENGINE COOLING SYSTEM WITH ELEVATED COOLANT TEMPERATURE RESEARCH ON THE MODEL TEST STAND

2015 ◽  
Vol 20 (4) ◽  
pp. 177-183
Author(s):  
Rafał Krakowski
Keyword(s):  
Internal Combustion Engine ◽  
Model Test ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Test Stand ◽  
Coolant Temperature ◽  
Engine Cooling

Study of the effect of the EGR heat exchanger on the internal combustion engine cooling system

2021 ◽  
Keyword(s):  
Heat Exchanger ◽  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Combustion Products ◽  
Simulation Software ◽  
One Dimensional ◽  
Engine Cooling ◽  
Recirculation System

The article presents a study and modification of the cooling system of a KAMAZ R6 in-line diesel engine using a heat exchanger of the combustion products recirculation system in the Simcenter AMESim one-dimensional simulation software. In the course of the research, the problems of engine overheating when using a heat exchanger of the combustion products recirculation system were identified, and possible solutions were proposed and investigated to optimize the temperature level of the coolant in the engine cooling system. Keywords one-dimensional modeling, 1D modeling, ICE, internal combustion engine, heat exchange, cooling system, CO, heat exchanger, heat exchanger, TA

Flatness-based control for an internal combustion engine cooling system

2011 ◽  
Author(s):  
Harald Aschemann ◽  
Robert Prabel ◽  
Christian Gross ◽  
Dominik Schindele
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Engine Cooling

scholarly journals Small Cogeneration Unit with Heat and Electricity Storage

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2102
Author(s):  
Josef Stetina ◽  
Michael Bohm ◽  
Michal Brezina
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Catalytic Converter ◽  
Storage System ◽  
Internal Combustion ◽  
Energy Storage System ◽  
Balance Model ◽  
Exhaust Pipe ◽  
Water Storage Tank

A micro cogeneration unit based on a three-cylinder internal combustion engine, Skoda MPI 1.0 L compressed natural gas (CNG), with an output of 25 kW at 3000 RPM is proposed in this paper. It is a relatively simple engine, which is already adopted by the manufacturer to operate on CNG. The engine life and design correspond to the original purpose of use in the vehicle. A detailed dynamic model was created in the GT-SUITE environment and implemented into an energy balance model that includes its internal combustion engine, heat exchangers, generator, battery storage, and water storage tank. The 1D internal combustion engine model provides us with information on engine start-up time, actual effective power, friction power, and the amount of heat going to the cooling system and exhaust pipe. The catalytic converter was removed from the exhaust pipe, and the engine was always operating at full load; thus, engine power control is not considered. An energy storage system for an island operation of the entire power unit for a large, detached house was designed to withstand accumulated energy for a few days in the case of a breakout. To reach a low initial system cost, the possible implementation of worn-out battery packs toward emission reduction in terms of the second life of the battery is proposed. The energy and emission balance are carried out, and the service life of the engine is also discussed.

Unified multidisciplinary modeling and simulation analysis of internal power system

2021 ◽  
pp. 1-21
Author(s):  
Guojin Chen ◽  
Chang Chen ◽  
Yiming Yuan ◽  
Yishuai Yue
Keyword(s):  
Internal Combustion Engine ◽  
Modeling And Simulation ◽  
Physical System ◽  
Cooling System ◽  
Combustion Engine ◽  
Control Unit ◽  
Internal Combustion ◽  
Power Equipment ◽  
Supply Rate ◽  
Multidisciplinary Modeling

The internal combustion power equipment is a typical cyber-physical system (CPS). The traditional design method is to separate the information system from the physical system, and then to simulate and optimize separately every system. That can not achieve the best performance. Aiming at the internal combustion power equipment with multi-disciplinary deep integration, this paper establishes the multi-disciplinary model of the whole and key components based on Dymola software. There are mainly mechanical system, combustion system, cooling system, control system and other simulation models, including deceleration and fuel cut-off control unit modeling, start-stop control unit modeling and speed limit control unit modeling. The performance of each model is simulated and analyzed. The mathematical models of engine characteristic curve and fuel supply rate curve are established through experimental study. Finally, taking the simulation model of automobile power system as an example, the simulation calculation and experimental verification are carried out, and the relationship among fuel supply rate, torque, speed and valve of internal combustion engine is obtained, as well as the cooling capacity of the cooling system is studied. The experimental results show that the maximum error between the simulation speed curve and the actual speed curve is within ± 2 km/h. The research results of this paper can provide theoretical basis for multidisciplinary modeling and simulation of internal combustion power equipment, and also provide technical support for performance analysis of internal combustion engine.

scholarly journals The Effect of Using a Modified A/C System on the Cooling System Temperature of an Internal Combustion Engine

2017 ◽  
Vol 07 (05) ◽  
pp. 92-99
Author(s):  
Mukhtar M.A. Morad ◽  
Abdulwahab A. Alnaqi ◽  
Ahmad E. Murad ◽  
Esam A.M. Husain ◽  
Hasan Mulla Ali ◽  
...  
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion ◽  
System Temperature

scholarly journals Improving the environmental performance of vehicles upgrading the cooling system of an internal combustion engine

2020 ◽  
Vol 3 (30) ◽  
pp. 110-112
Author(s):  
S.V. Zaichenko ◽  
V.O. Shalenko ◽  
L.I. Zaichenko ◽  
K.V. Krupa
Keyword(s):  
Internal Combustion Engine ◽  
Environmental Performance ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion

A Method for Preoptimising the Internal Combustion Engine Air Cooling System

1998 ◽  
Author(s):  
E. Navarro Arévalo ◽  
D. L. Fernández Melcón ◽  
R. Marcos Álvarez ◽  
P. Pérez Illana
Keyword(s):  
Internal Combustion Engine ◽  
Cooling System ◽  
Combustion Engine ◽  
Internal Combustion ◽  
Air Cooling ◽  
Air Cooling System
Sign in / Sign up

Export Citation Format

Share Document