A Boundary-Element Method for Slamming Analysis

1982 ◽  
Vol 26 (02) ◽  
pp. 117-124
Author(s):  
Thomas L. Geers
Keyword(s):  
Experimental Data ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Boundary Element Method ◽  
Boundary Element ◽  
Element Analysis ◽  
Structure Interaction ◽  
The Finite Element Analysis ◽  
Computational Resources ◽  
Element Method

A boundary-element method for treatment of the fluid-structure interaction in slamming analysis is described. The method emphasizes simplicity and efficiency, so that the analyst may devote most of his computational resources to the analysis of the structure. Numerical results for a number of rigid-impactor problems are compared with analytical solutions and experimental data, and procedures for the finite-element analysis of flexible impactors are discussed.

The Finite Element Analysis of Omni-Direction Side-Loading Forklift Truck Lifting System Based on COSMOSWorks

2012 ◽  
Vol 184-185 ◽  
pp. 534-537
Author(s):  
Jing Jing Zhou ◽  
Ai Dong Guo ◽  
Chun Hui Li ◽  
Zhen Jiang Lin ◽  
Tie Zhuang Wu
Keyword(s):  
Experimental Data ◽  
Mechanical Properties ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Optimization ◽  
Experimental Measurements ◽  
Element Analysis ◽  
Forklift Truck ◽  
The Finite Element Analysis ◽  
Lifting System

By setting contact sets, achieved overall analysis results of the mechanical properties with omni-direction side-loading forklift truck lifting system based on COSMOSWorks. And made an experimental measurements to omni-direction side-loading forklift truck lifting system by electrometric methods. There was a good relevance between experimental data and calculation values, and the deviation was basically within the 10 percent allowed. Finally, in this way it verified the correctness and reliability of the finite element analysis by experimental measurements. Ensured the omni-direction side-loading forklift truck lifting system could be safe and efficient to work. And also it laid a foundation for subsequent structural optimization.

Finite Element Calculation of Sintering Deformation Using Limited Experimental Data

2008 ◽  
Vol 606 ◽  
pp. 103-118 ◽  
Author(s):  
Jing Zhe Pan ◽  
Ruo Yu Huang
Keyword(s):  
Experimental Data ◽  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Ceramic Powder ◽  
Material Model ◽  
Element Analysis ◽  
Ceramic Components ◽  
On Line ◽  
Element Method

Predicting the sintering deformation of ceramic powder compacts is very important to manufactures of ceramic components. In theory the finite element method can be used to calculate the sintering deformation. In practice the method has not been used very often by the industry for a very simple reason – it is more expensive to obtain the material data required in a finite element analysis than it is to develop a product through trial and error. A finite element analysis of sintering deformation requires the shear and bulk viscosities of the powder compact. The viscosities are strong functions of temperature, density and grain-size, all of which change dramatically in the sintering process. There are two ways to establish the dependence of the viscosities on the microstructure: (a) by using a material model and (b) by fitting the experimental data. The materials models differ from each other widely and it can be difficult to know which one to use. On the other hand, obtaining fitting functions is very time consuming. To overcome this difficulty, Pan and his co-workers developed a reduced finite element method (Kiani et. al. J. Eur. Ceram. Soc., 2007, 27, 2377-2383; Huang and Pan, J. Eur. Ceram. Soc., available on line, 2008) which does not require the viscosities; rather the densification data (density as function of time) is used to predict sintering deformation. This paper provides an overview of the reduced method and a series of case studies.

Research of the FEM Mesh Generation Based on Patran

2014 ◽  
Vol 525 ◽  
pp. 731-735 ◽  
Author(s):  
Qian Peng Han ◽  
Bo Peng
Keyword(s):  
Finite Element Method ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Mesh Generation ◽  
Mechanical Design ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Element Method

Finite element method(FEM) have been widely used in modern mechanical design,mesh generation is an important part of the finite element analysis,this article discussed the process of mesh generation through two practical cases and put forward some issues we should pay more attention to.

Mathematical Modeling and Experimental Study on Electrochemical Deburring of Miniature Holes

2013 ◽  
Vol 721 ◽  
pp. 382-386 ◽  
Author(s):  
Ze Fei Wei ◽  
Xing Hua Zheng ◽  
Zi Yuan Yu
Keyword(s):  
Mathematical Modeling ◽  
Experimental Data ◽  
Mathematical Model ◽  
Finite Element Analysis ◽  
Experimental Study ◽  
Finite Element ◽  
Electrochemical Machining ◽  
Current Density Distribution ◽  
Element Analysis ◽  
The Finite Element Analysis

The paper mainly focused on burr removal of the miniature hole drilled on aluminum plate by electrochemical machining. A mathematical model for the electrochemical deburring of miniature holes (M-ECD) was established based on the finite element analysis to the current density distribution. Both theoretical analysis and experimental study were held on the effects of many factors to the deburring results. The results proved that predictions based on our mathematical model were agreed with the experimental data comparatively.

Distortion Simulation of Unsymmetrical Composite Laminates Using the Finite Element Analysis Method

2007 ◽  
Vol 546-549 ◽  
pp. 1563-1566
Author(s):  
Min Li ◽  
Bao Yan Zhang ◽  
Xiang Bao Chen
Keyword(s):  
Experimental Data ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Composite Laminates ◽  
Shell Element ◽  
Element Analysis ◽  
Unsymmetric Laminates ◽  
The Finite Element Analysis ◽  
Simulation Results ◽  
The Difference

Unsymmetric composite laminates were benefit to reducing the structure weight of some aircrafts. However, the cured unsymmetric laminates showed distortion at room temperature. Therefore, predicting the deformation before using the unsymmetrical composite is very important. In this study an attempt was made to predict the shapes of some unsymmetric cross-ply laminates using the finite element analysis (FEA). The bilinear shell-element was adopted in the process. Then the simulation results were compared with the experimental data. The studies we had performed showed that the theoretical calculation agreed well with the experimental results, the predicted shapes were similar to the real laminates, and the difference between the calculated maximum deflections and the experimental data were less than 5%. Hence the FEA method was suitable for predicting the warpage of unsymmetric laminates. The error analysis showed that the simulation results were very sensitive to the lamina thickness, 2 α and (T.

Sign in / Sign up

Export Citation Format

Share Document