Position control for haptic device based on discrete-time proportional integral derivative controller

Haptic devices had known as advanced technology with the goal is creating the experiences of touch by applying forces and motions to the operator based on force feedback. Especially in unmanned aerial vehicle (UAV) applications, the position of the end-effector Falcon haptic sets the velocity command for the UAV. And the operator can feel the experience vibration of the vehicle as to the acceleration or collision with other objects through a forces feedback to the haptic device. In some emergency cases, the haptic can report to the user the dangerous situation of the UAV by changing the position of the end-effector which is be obtained by changing the angle of the motor using the inverse kinematic equation. But this solution may not accurate due to the disturbance of the system. Therefore, we proposed a position controller for the haptic based on a discrete-time proportional integral derivative (PID) controller. A Novint Falcon haptic is used to demonstrate our proposal. From hardware parameters, a Jacobian matrix is calculated, which combines with the force output from the PID controller to make the torque for the motors of the haptic. The experiment was shown that the PID has high accuracy and a small error position.

Experimental Evaluation on Haptic Feedback Accuracy by Using Two Self-Made Haptic Devices and One Additional Interface in Robotic Teleoperation

The goal of haptic feedback in robotic teleoperation is to enable users to accurately feel the interaction force measured at the slave side and precisely understand what is happening in the slave environment. The accuracy of the feedback force describing the error between the actual feedback force felt by a user at the master side and the measured interaction force at the slave side is the key performance indicator for haptic display in robotic teleoperation. In this paper, we evaluate the haptic feedback accuracy in robotic teleoperation via experimental method. A special interface iHandle and two haptic devices, iGrasp-T and iGrasp-R, designed for robotic teleoperation are developed for experimental evaluation. The device iHandle integrates a high-performance force sensor and a micro attitude and heading reference system which can be used to identify human upper limb motor abilities, such as posture maintenance and force application. When a user is asked to grasp the iHandle and maintain a fixed position and posture, the fluctuation value of hand posture is measured to be between 2 and 8 degrees. Based on the experimental results, human hand tremble as input noise sensed by the haptic device is found to be a major reason that results in the noise of output force from haptic device if the spring-damping model is used to render feedback force. Therefore, haptic rendering algorithms should be independent of hand motion information to avoid input noise from human hand to the haptic control loop in teleoperation. Moreover, the iHandle can be fixed at the end effector of haptic devices; iGrasp-T or iGrasp-R, to measure the output force/torque from iGrasp-T or iGrasp-Rand to the user. Experimental results show that the accuracy of the output force from haptic device iGrasp-T is approximately 0.92 N, and using the force sensor in the iHandle can compensate for the output force inaccuracy of device iGrasp-T to 0.1 N. Using a force sensor as the feedback link to form a closed-loop feedback force control system is an effective way to improve the accuracy of feedback force and guarantee high-fidelity of feedback forces at the master side in robotic teleoperation.

Development and Validation of a Mixed Reality Configuration of a Simulator for a Minimally Invasive Spine Surgery Using the Workspace of a Haptic Device and Simulator Users

Most surgical simulators leverage virtual or bench models to simulate reality. This study proposes and validates a method for workspace configuration of a surgical simulator which utilizes a haptic device for interaction with a virtual model and a bench model to provide additional tactile feedback based on planned surgical manoeuvers. Numerical analyses were completed to determine the workspace and position of a haptic device, relative to the bench model, used in the surgical simulator, and the determined configuration was validated using device limitations and user data from surgical and nonsurgical users. For the validation, surgeons performed an identical surgery on a cadaver prior to using the simulator, and their trajectories were then compared to the determined workspace for the haptic device. The configuration of the simulator was determined appropriate through workspace analysis and the collected user trajectories. Statistical analyses suggest differences in trajectories between the participating surgeons which were not affected by the imposed haptic workspace. This study, therefore, demonstrates a method to optimally position a haptic device with respect to a bench model while meeting the manoeuverability needs of a surgical procedure. The validation method identified workspace position and user trajectory towards ideal configuration of a mixed reality simulator.