Parameter substantiation of supra bit jet pump for productive formation opening

The purpose of the study is to develop a supra bit jet pump taking into account the unsteadiness of low-speed drilling for crushing the cuttings injected from the annular space under productive formation opening. The article proposes a device for drill string bottom assembly intended for the initial opening of the productive formation. The device includes a supra bit jet pump and a colmatator. The jet pump creates an additional circulation loop of the drilling fluid above the well bottom, crushes the cuttings injected from the annular space in the mixing chamber and delivers it to the colmatator. An additional circulation loop above the well bottom creates a local drawdown of the formation while maintaining the hydrostatic pressure in the well. Crushing of cuttings in the mixing chamber of the jet pump occurs due to the creation of cross flows in the jet pump. The cross flows are provided due to the angular and eccentric displacement of the working nozzle of the jet pump relative to the mixing chamber. The colmatator creates an impermeable screen on the borehole wall for temporary isolation of the productive formation under initial opening. The conducted study allowed the authors to propose head characteristics of the jet pump taking into account the angular, eccentric displacement of the working nozzle. The head characteristic of the jet pump has been developed for the unsteady operation of the jet pump in the drill string bottom assembly. The head characteristics take into account the roughness of the flow path of the jet pump. Using the head characteristics, the permissible displacements of the working nozzle of the jet pump have been determined. Recommendations for the design of jet pumps for drill string bottom assemblies are proposed.

Experimental and computational study of a low-pressure natural circulation loop

The experimental and analytical study of single-phase flow and heat transfer in natural circulation loop has been carried out. Experiments were performed on water and ethanol that are the liquids with significantly different thermophysical properties. Experimental apparatus was a rectangular shaped loop with vertical flow up leg. The flow up and flow down legs of the loop are joined to the separator-condenser at the top of the loop. The upper limit of heat flux densities in the experiments was set with the consideration for flow regime to remain in single phase state along the whole heated length. Wall temperature time records being registered at different distances from the inlet to the heated zone indicate the occurrence of temperature fluctuations near the exit from heated zone even at relatively low heat flux densities. This fact displaces a complex changing of velocity profiles along the tube with vortex formation and occurrence of flow instability. Experimental data on longitudinal wall temperature distributions of heated section have been used to test a modified method of hydraulic calculation of the loop. It was pointed out that in spite of long year (since early 1950s) experimental, analytical and numerical investigations of natural circulation loops no suitable predicting recommendations for heat transfer and friction have been proposed till today for engineering hydraulic calculations of single-phase natural circulation loops.

Investigating heat transfer in an upward flow of liquid metal in the mercury facility with a loop of natural circulation

Research of heat transfer is performed in an upward flow of liquid metal in a vertical channel of rectangular cross-section under the condition of one-sided heating and in a vertical pipe in a mercury circuit with a natural circulation loop. Natural circulation loop enables measurements in mixed turbulent convection modes, which are inaccessible on a contour with a forced convection, that is, in the region of small Reynolds (Peclet) numbers of characteristics. Using a two-coordinate probe with a microthermocouple correlation sensor, profiles of averaged velocity and temperature and distribution of a wall temperature are obtained, and heat transfer coefficients are determined. Criterion dependences of Nusselt number on Peclet and Richardson are built. Experimental data on heat transfer are compared with similar data obtained earlier in a loop with a forced flow of mercury.

Steady-state and nonlinear stability analysis for the feasibility of different fluids in a supercritical natural circulation loop

A numerical model for a supercritical natural circulation loop is developed to examine the flow instabilities by nonlinear stability analysis. The supercritical natural circulation loop is a loop geometry, which is driven by natural circulation with supercritical fluids as a coolant. A mathematical formulation is developed to study the steady-state and transient solution procedure for supercritical natural circulation loop. This mathematical model is then used to perform various parametric studies with different supercritical fluids (water, [Formula: see text], R134a, ammonia, R22, propane, and isobutane). The behavior of all the fluids is analyzed on identical geometrical and operating conditions. A comprehensive numerical study of the nonlinear stability analysis is presented with particular emphasis on the feasibility of various fluids in a natural circulation loop environment. The 50% increment in loop diameter and height increased the stable operating zones and shifted the marginal stability boundary upward respectively by approximately three times and 25–40% of the previous value. However, further increase in diameter and height reduces the increment of stable operating zones; hence the marginal stability boundary shifts upward marginally than the previous value. Furthermore, the marginal stability boundaries are generated to identify the stable and unstable zones for the available geometrical and operating conditions.