Carbide Coated Cutting Tool Properties Investigation by Nano-Mechanical Measurements under 250–500°C

2008 ◽  
pp. 79-80
Author(s):  
B. Vasques ◽  
D. Joly ◽  
R. Leroy ◽  
N. Ranganathan ◽  
P. Donnadieu
Keyword(s):  
Cutting Tool ◽  
Mechanical Measurements

The Chatterbox: A Device for Hearing Chatter as Sections are Cut

1973 ◽  
Vol 31 ◽  
pp. 360-361
Author(s):  
C. W. McCutchen ◽  
Lois W. Tice
Keyword(s):  
Machine Tools ◽  
Cutting Tool ◽  
Guerilla Warfare ◽  
History Of ◽  
Chatter Marks

Ultramicrotomists live in a state of guerilla warfare with chatter. This situation is likely to be permanent. We can infer this from the history of machine tools. If set the wrong way for the particular combination of cutting tool and material, most if not all machine tools will chatter.In more than 100 years since machine tools became common, no one has evolved a practical recipe that guarantees avoiding chatter. Rather than follow some single very conservative rule to avoid chatter in all cases, machinists detect it when it happens, and change conditions until it stops. This is possible because they have no trouble telling when their cutting tool is chattering. They can see chatter marks, and they can also hear a sometimes deafening noise.

Ultrasonic Measurement of Sheet Steel Texture and Formability: Comparison with Neutron Diffraction and Mechanical Measurements

1990 ◽  
Vol 2 (1) ◽  
pp. 239-257
Author(s):  
A. V. Clark ◽  
R. B. Thompson ◽  
Y. Li ◽  
R. C. Reno ◽  
G. V. Blessing ◽  
...  
Keyword(s):  
Neutron Diffraction ◽  
Sheet Steel ◽  
Ultrasonic Measurement ◽  
Mechanical Measurements

RELATION BETWEEN COMPOSITION, MICROSTRUCTURE AND CUTTING TOOL PERFORMANCE OF ALPHA-BETA-SiALONs

1986 ◽  
Vol 47 (C1) ◽  
pp. C1-347-C1-352 ◽  
Author(s):  
N. INGELSTRÖM ◽  
T. EKSTRÖM
Keyword(s):  
Cutting Tool ◽  
Tool Performance ◽  
Alpha Beta

Dynamics of the processes in metal machining

1998 ◽  
Vol 2 ◽  
pp. 115-122
Author(s):  
Donatas Švitra ◽  
Jolanta Janutėnienė
Keyword(s):  
High Frequency ◽  
Machine Tools ◽  
Metal Cutting ◽  
Cutting Tool ◽  
Low Frequency ◽  
Metal Cutting Machine ◽  
Cutting Machine ◽  
Metal Machining

In the practice of processing of metals by cutting it is necessary to overcome the vibration of the cutting tool, the processed detail and units of the machine tool. These vibrations in many cases are an obstacle to increase the productivity and quality of treatment of details on metal-cutting machine tools. Vibration at cutting of metals is a very diverse phenomenon due to both it’s nature and the form of oscillatory motion. The most general classification of vibrations at cutting is a division them into forced vibration and autovibrations. The most difficult to remove and poorly investigated are the autovibrations, i.e. vibrations arising at the absence of external periodic forces. The autovibrations, stipulated by the process of cutting on metalcutting machine are of two types: the low-frequency autovibrations and high-frequency autovibrations. When the low-frequency autovibration there appear, the cutting process ought to be terminated and the cause of the vibrations eliminated. Otherwise, there is a danger of a break of both machine and tool. In the case of high-frequency vibration the machine operates apparently quiently, but the processed surface feature small-sized roughness. The frequency of autovibrations can reach 5000 Hz and more.

EFFECT OF A PROTECTIVE COATING ON THE TEMPERATURE DISTRIBUTION IN A REVOLVING CUTTING TOOL AND THE CUTTING TOOL LIFETIME

2018 ◽  
Vol 22 (4) ◽  
pp. 279-291
Author(s):  
Alexander Goncharov ◽  
Andrey Yunda ◽  
Evgenii Mironenko ◽  
Dmitrii Belous ◽  
Liudmila Vasilyeva
Keyword(s):  
Temperature Distribution ◽  
Protective Coating ◽  
Cutting Tool

Isolation and characterization of oleochemical compounds from watermelon seed

2020 ◽  
Vol 10 (4) ◽  
pp. 79-82
Author(s):  
Madhubhushan M ◽  
Seshaiah S ◽  
Chandrudu J ◽  
Sagar R ◽  
Akila CR
Keyword(s):  
Cutting Tool ◽  
Citrullus Lanatus ◽  
Fatty Esters ◽  
Mineral Oils ◽  
Light Yellow ◽  
Isolation And Characterization ◽  
The Common ◽  
Set Up ◽  
Natural Gradation

The common watermelon item (Citrullus lanatus) seeds were gained from castoffs verdant nourishments for use by decorating, sun ventilation and pulverizing. Light yellow-toned oil was gotten by dissolvable withdrawal using oil atmosphere and the going with traits were gotten using oil ether: pH, refractive rundown, thickness, dissolvable miscibility, coagulating temperature, fire nature, express gravity, streak point and warmth of consuming. With a shallow level of unsaturation, stepped level of smoothness, and proximity of raised degree of the sensible proportion of free unsaturated fats. The low assessment of the solidifying temperature of the oil offered a hint that the oil can be managed in various areas paying little heed to the qualification in temperature. The following level of linoleic destructive of the oil offers a hint of natural gradation of solidarity. Fatty esters are increasing expanding significance as a biodegradable swap for mineral oils. In some request regions, for example, cutting tool oil, gearbox, pressure-driven oils, and greases for raw petroleum creation, the oleochemical items are set up. Nonetheless, certain particular wellsprings of fatty esters are hitherto to be abused for this comparative reason. This exploration subsequently tests into one of the less used wellsprings of fatty esters in watermelon. The oil from the kernels demonstrations a top-notch yield presents significant utilitarian gatherings for change and thus was utilized to set up an assortment of oleochemicals which demonstrated excellence materials in contrast with the routinely utilized oils feed frameworks for oleochemicals after portrayal. The photopolymers acquired indicated piercing vinyl protons for consistent polymerize.

Sign in / Sign up

Export Citation Format

Share Document