Dynamic Centrifuge Modelling Tests for Sliding Rock Slopes

2014 ◽  
pp. 75-79 ◽  
Author(s):  
Xianglong Li ◽  
Joseph Wartman ◽  
Huiming Tang ◽  
Jinkai Yan ◽  
Hongming Luo ◽  
...  
Keyword(s):  
Rock Slopes ◽  
Centrifuge Modelling

Dynamic Centrifuge Modelling Tests for Toppling Rock Slopes

2015 ◽  
pp. 769-774 ◽  
Author(s):  
Xianglong Li ◽  
Huiming Tang ◽  
Chengren Xiong ◽  
Joseph Wartman ◽  
Yueping Yin
Keyword(s):  
Rock Slopes ◽  
Centrifuge Modelling

STABILITY ANALYSIS OF WEATHERED VOLCANIC ROCK SLOPES IN THE CARIBBEAN

2019 ◽  
Author(s):  
Rachel Capps ◽  
◽  
Scott Brame ◽  
Audrey Crafton
Keyword(s):  
Stability Analysis ◽  
Volcanic Rock ◽  
Rock Slopes ◽  
The Caribbean

scholarly journals An Energy-Based Discrete Element Modeling Method Coupled with Time-Series Analysis for Investigating Deformations and Failures of Jointed Rock Slopes

2021 ◽  
Vol 11 (12) ◽  
pp. 5447
Author(s):  
Xiaona Zhang ◽  
Gang Mei ◽  
Ning Xi ◽  
Ziyang Liu ◽  
Ruoshen Lin
Keyword(s):  
Time Series ◽  
Iterative Process ◽  
Discrete Element ◽  
Jointed Rock ◽  
Modeling Method ◽  
Discrete Element Modeling ◽  
Rock Slopes ◽  
Sliding Surface ◽  
Element Modeling ◽  
Displacement Based

The discrete element method (DEM) can be effectively used in investigations of the deformations and failures of jointed rock slopes. However, when to appropriately terminate the DEM iterative process is not clear. Recently, a displacement-based discrete element modeling method for jointed rock slopes was proposed to determine when the DEM iterative process is terminated, and it considers displacements that come from rock blocks located near the potential sliding surface that needs to be determined before the DEM modeling. In this paper, an energy-based discrete element modeling method combined with time-series analysis is proposed to investigate the deformations and failures of jointed rock slopes. The proposed method defines an energy-based criterion to determine when to terminate the DEM iterative process in analyzing the deformations and failures of jointed rock slopes. The novelty of the proposed energy-based method is that, it is more applicable than the displacement-based method because it does not need to determine the position of the potential sliding surface before DEM modeling. The proposed energy-based method is a generalized form of the displacement-based discrete element modeling method, and the proposed method considers not only the displacement of each block but also the weight of each block. Moreover, the computational cost of the proposed method is approximately the same as that of the displacement-based discrete element modeling method. To validate that the proposed energy-based method is effective, the proposed method is used to analyze a simple jointed rock slope; the result is compared to that achieved by using the displacement-based method, and the comparative results are basically consistent. The proposed energy-based method can be commonly used to analyze the deformations and failures of general rock slopes where it is difficult to determine the obvious potential sliding surface.

Dynamic analysis of anti-dip bedding rock slopes reinforced by pre-stressed cables using discrete element method

2021 ◽  
Vol 130 ◽  
pp. 79-93
Author(s):  
Yun Zheng ◽  
Runqing Wang ◽  
Congxin Chen ◽  
Chaoyi Sun ◽  
Zhanghao Ren ◽  
...  
Keyword(s):  
Discrete Element Method ◽  
Dynamic Analysis ◽  
Discrete Element ◽  
Rock Slopes ◽  
Element Method
Sign in / Sign up

Export Citation Format

Share Document