The Effect of the Bedding Length of Lintel in Masonry Walls on Their Load Bearing Capacity

2014 ◽  
pp. 1-16
Author(s):  
Jure Radnić ◽  
Vatroslav Čamber ◽  
Nikola Grgić ◽  
Domagoj Matešan
Keyword(s):  
Bearing Capacity ◽  
Masonry Walls ◽  
Load Bearing Capacity ◽  
Load Bearing

Composite action in masonry walls under vertical in-plane loading: experimental results compared with predictions

2015 ◽  
Vol 42 (7) ◽  
pp. 449-462
Author(s):  
A.T. Vermeltfoort ◽  
D.R.W. Martens
Keyword(s):  
Bearing Capacity ◽  
Concrete Beam ◽  
Concrete Beams ◽  
Compressive Force ◽  
Reinforced Concrete Beams ◽  
Elastic Behavior ◽  
Masonry Walls ◽  
Load Bearing Capacity ◽  
Cracking Behavior ◽  
Load Bearing

The results of five experimental test series on masonry walls supported by reinforced concrete beams or slabs are reported and compared to theoretical predictions of the load bearing capacity. The experiments were performed on deep masonry beams built with respectively calcium silicate and clay brick. Investigated parameters were: position of the supports, concrete beam-masonry interface, concrete beam stiffness, type of loading, and height of masonry wall and concrete beam. Based on literature, the method proposed by Davies and Ahmed as well as the method according to Eurocode 6 were used to estimate the load bearing capacity of the tested masonry walls supported by concrete beams. The method of Davies and Ahmed allows for the determination of the stresses and stress resultants in the masonry. The analysis shows that near the support an inclined compressive force acts at the bed joint, which means that a shear-compression stress state exists in the bed joint. Strength evaluation has been carried out using the Mann-Müller criterion that is adopted in Eurocode 6. Based on the test results, it may be concluded that both methods yield conservative values of the load bearing capacity, as could be expected. Before cracking a linear elastic behavior was observed, while after cracking a strut-and-tie model may be applied. To develop more accurate design models, it is recommended to investigate the post-cracking behavior in more detail.

Nonlinear structural analysis of a masonry wall

2021 ◽  
Author(s):  
Guangli Du ◽  
Thomas Cornelius ◽  
Joergen Nielsen ◽  
Lars Zenke Hansen
Keyword(s):  
Bearing Capacity ◽  
Material Properties ◽  
Slenderness Ratio ◽  
Masonry Wall ◽  
Masonry Walls ◽  
Vertical Load ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Support Conditions ◽  
Theoretical Developments

<p>Structural modelling of a masonry wall is challenging due to material properties, eccentricity of the vertical load, slenderness ratio etc. In recent theoretical developments for design of masonry walls, a new “Phi” method to determine the eccentricity is adopted in Eurocode 6. However, the comparisons between this method and the conventional “Ritter” method shows that for certain prerequisites it would result in substantial different load-bearing capacity. Hence, in order to investigate how support conditions influence the load bearing capacity of the wall, this study performs a nonlinear numerical analysis of a wall for several load cases in ABAQUS and the result is verified with an independently developed calculation tool using MATLAB. The results show that the top rotation plays a significant role for the load bearing capacity of the masonry wall supported by slabs at both ends. It is difficult to estimate the eccentricities without a rigorous calculation.</p>

scholarly journals The influence of the moisture content in historical masonry walls on the load bearing capacity

2018 ◽  
Vol 49 ◽  
pp. 00100
Author(s):  
Monika Siewczynska ◽  
Barbara Ksit
Keyword(s):  
Moisture Content ◽  
Bearing Capacity ◽  
Actual State ◽  
Masonry Walls ◽  
Historical Buildings ◽  
Load Bearing Capacity ◽  
Reliable Determination ◽  
Load Bearing ◽  
Historical Masonry

The moisture content in historical masonry walls, particularly on the ground floor, caused by i.e. lack of damp insulation, is a phenomenon of common occurrence. It is usually analysed in terms of mycological changes, thermal insulation and frost damage. The paper discusses the influence of the increased moisture content on the weight and load bearing capacity of the structure. The determination of moisture content in masonry elements, performed during the inspection of the building, provides information from which an increase in the structure's weight can be defined. Reliable tests for the moisture content and compressive strength of masonry and mortar components are invasive, and the number of testing in historical buildings should be limited to the minimum necessary to preserve their vintage nature. As a result, the received overall picture of the work of masonry may not be consistent with its actual state since historical buildings could have been rebuilt or repaired, and consequently, contain masonry conversions made of various materials with different properties. Absorbability can serve here as an example as it is a factor that disrupts a reliable determination of load bearing capacity values of masonry structures. The article attempts to determine the change in load bearing capacity of a moist masonry structure compared to the original - in the air-dry state - for various types of historical masonry and mortar components. The main influence analysed was due to capillary action, whereas the effect of other sources of moisture, i.e. salinity, was excluded.

scholarly journals Application of Artificial Neural Network to Predict Load Bearing Capacity and Stiffness of Perforated Masonry Walls

CivilEng ◽  
2021 ◽  
Vol 2 (1) ◽  
pp. 48-67
Author(s):  
Mohsen Khaleghi ◽  
Javid Salimi ◽  
Visar Farhangi ◽  
Mohammad Javad Moradi ◽  
Moses Karakouzian
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Bearing Capacity ◽  
Structural Damage ◽  
Masonry Walls ◽  
Initial Stiffness ◽  
Load Bearing Capacity ◽  
Load Bearing ◽  
Artificial Neural ◽  
Mp Method

Perforations adversely affect the structural response of unreinforced masonry walls (UMW) by reducing the wall’s load bearing capacity, which can cause serious structural damage. In the absence of a reliable procedure to accurately predict the load bearing capacity and stiffness of perforated masonry walls subjected to in-plane loadings, this study presents a novel approach to measure these parameters by developing simple but practical equations. In this regard, the Multi-Pier (MP) method as a numerical approach was employed along with the application of an Artificial Neural Network (ANN). The simulated responses of centrally perforated UMW by the MP method were validated utilizing full-scale experimental walls. The validated MP model was used to generate a simulated database. The simulated database includes results of analyses for 49 different configurations of perforated masonry walls and their corresponding solid masonry walls. The effect of the area and shape of the perforations on the UMW’s behavior was evaluated by the MP method. Following the outcomes of the verified MP method, the ANN is trained to develop empirical equations to accurately predict the reduction in the load bearing capacity and initial stiffness due to the perforation of UMW. The results of this study indicate that the perforations have a significant effect on the structural capacity of the UMW subjected to in-plane loadings.

Sign in / Sign up

Export Citation Format

Share Document