Numerical Simulation of 3D Unsteady Heat Transfer at Strongly Deformed Droplets at High Reynolds Numbers

2003 ◽  
pp. 255-266 ◽  
Author(s):  
Matthias Hase ◽  
Bernhard Weigand
Keyword(s):  
Heat Transfer ◽  
Numerical Simulation ◽  
Reynolds Numbers ◽  
Unsteady Heat Transfer ◽  
High Reynolds Numbers ◽  
High Reynolds

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

Temperature Control of Blow-Down, Supersonic Tunnels

1956 ◽  
Vol 60 (541) ◽  
pp. 67-70
Author(s):  
T. A. Thomson
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Stagnation Temperature ◽  
Blow Down ◽  
High Reynolds Numbers ◽  
Experimental Errors ◽  
High Reynolds

The blow-down type of intermittent, supersonic tunnel is attractive because of its simplicity and because relatively high Reynolds numbers can be obtained for a given size of test section. An adverse characteristic, however, is the fall of stagnation temperature during runs, which can affect experiments in several ways. The Reynolds number varies and the absolute velocity is not constant, even if the Mach number and pressure are; heat-transfer cannot be studied under controlled conditions and the experimental errors arising from the effect of heat-transfer on the boundary layer vary in time. These effects can become significant in quantitative experiments if the tunnel is large and the variation of temperature very rapid; the expense required to eliminate them might then be justified.

New thermal-hydraulic correlations for printed circuit heat exchangers (PCHEs) with zigzag channels under high Reynolds numbers

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Carolina P. Naveira-Cotta ◽  
Jian Su ◽  
Paulo Lucena Kreppel Paes ◽  
Philippe R. Egmont ◽  
Rodrigo P. M. Moreira ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Design Parameters ◽  
Channel Diameter ◽  
Content Type ◽  
Printed Circuit ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
The Impact

Purpose The purpose of this paper is to investigate the impact of semi-circular zigzag-channel printed circuit heat exchanger (PCHE) design parameters on heat transfer and pressure drop of flows under high Reynolds numbers and provide new thermal-hydraulic correlations relevant to conditions encountered in natural gas processing plants. Design/methodology/approach The correlations were developed using three-dimensional steady-state computational fluid dynamics simulations with varying semicircular channel diameter (from 1 to 5 mm), zigzag angle (from 15° to 45°) and Reynolds number (from 40,000 to 100,000). The simulation results were validated by comparison with experimental results and existing correlations. Findings The results revealed that the thermal-hydraulic performance was mostly affected by the zigzag angle, followed by the ratio of the zigzag channel length to the hydraulic diameter. Overall, smaller zigzag angles favored heat transfer intensification while keeping reasonably low pressure drops. Originality/value This study is, to date, the only one providing thermal-hydraulic correlations for PCHEs with zigzag channels under high Reynolds numbers. Besides, the broad range of parameters considered makes the proposed correlations valuable PCHE design tools.

Sign in / Sign up

Export Citation Format

Share Document