Temperature Control of Blow-Down, Supersonic Tunnels

1956 ◽  
Vol 60 (541) ◽  
pp. 67-70
Author(s):  
T. A. Thomson
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Reynolds Numbers ◽  
Stagnation Temperature ◽  
Blow Down ◽  
High Reynolds Numbers ◽  
Experimental Errors ◽  
High Reynolds

The blow-down type of intermittent, supersonic tunnel is attractive because of its simplicity and because relatively high Reynolds numbers can be obtained for a given size of test section. An adverse characteristic, however, is the fall of stagnation temperature during runs, which can affect experiments in several ways. The Reynolds number varies and the absolute velocity is not constant, even if the Mach number and pressure are; heat-transfer cannot be studied under controlled conditions and the experimental errors arising from the effect of heat-transfer on the boundary layer vary in time. These effects can become significant in quantitative experiments if the tunnel is large and the variation of temperature very rapid; the expense required to eliminate them might then be justified.

Heat Transfer Coefficient Distribution of W and Broken W Turbulators At High Reynolds Numbers

2021 ◽  
pp. 1-29
Author(s):  
Sam Ghazi-Hesami ◽  
Dylan Wise ◽  
Keith Taylor ◽  
Étienne Robert ◽  
Peter Ireland
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Thermal Performance ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
Smooth Channel ◽  
Wide Range ◽  
High Reynolds

Abstract An experimental and numerical study of the convective heat transfer enhancement provided by two rib families (W and Broken W) is presented, covering Reynolds numbers (Re) between 300,000 to 900,000 in a straight channel with a rectangular cross section (AR=1.29). These high Reynolds numbers were selected for the current study since most data in the available literature typically pertain to investigations at lower Reynolds numbers. The objective of this study is to assess the local heat transfer coefficient (HTC) enhancement (compared with a smooth channel) and the overall thermal performance, taking into account the effect of increased roughness on the friction factor, of a group of W shaped turbulators over a wide range of Reynolds numbers. Furthermore, the effects of increasing the rib spacing on the thermal performance of the Broken W configuration are presented and discussed. The numerical results are compared against heat transfer measurements obtained using the Transient Liquid Crystal (TLC) method. The research shows that for the Broken W turbulators, increasing the Reynolds number is associated with an overall decrease of the thermal performance while the thermal performance of the W configuration is relatively insensitive to Reynolds number. Nevertheless, the Broken W configuration delivers higher thermal performance and heat transfer compared with the W configuration for the range of Re investigated. The Broken W configuration with a pitch spacing of 10 times the rib height was shown to provide the optimal thermal performance in the configurations investigated here.

Turbulent boundary layer statistics at very high Reynolds number

2015 ◽  
Vol 779 ◽  
pp. 371-389 ◽  
Author(s):  
M. Vallikivi ◽  
M. Hultmark ◽  
A. J. Smits
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
High Reynolds Number ◽  
Reynolds Numbers ◽  
Working Fluid ◽  
Mean Velocity ◽  
High Reynolds Numbers ◽  
Layer Flow ◽  
High Reynolds ◽  
Very High

Measurements are presented in zero-pressure-gradient, flat-plate, turbulent boundary layers for Reynolds numbers ranging from $\mathit{Re}_{{\it\tau}}=2600$ to $\mathit{Re}_{{\it\tau}}=72\,500$ ($\mathit{Re}_{{\it\theta}}=8400{-}235\,000$). The wind tunnel facility uses pressurized air as the working fluid, and in combination with MEMS-based sensors to resolve the small scales of motion allows for a unique investigation of boundary layer flow at very high Reynolds numbers. The data include mean velocities, streamwise turbulence variances, and moments up to 10th order. The results are compared to previously reported high Reynolds number pipe flow data. For $\mathit{Re}_{{\it\tau}}\geqslant 20\,000$, both flows display a logarithmic region in the profiles of the mean velocity and all even moments, suggesting the emergence of a universal behaviour in the statistics at these high Reynolds numbers.

Effect of Free-Stream Turbulence on Heat Transfer through a Turbulent Boundary Layer

1978 ◽  
Vol 100 (4) ◽  
pp. 671-677 ◽  
Author(s):  
J. C. Simonich ◽  
P. Bradshaw
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Reynolds Number ◽  
Free Stream ◽  
Reynolds Numbers ◽  
Skin Friction Coefficient ◽  
Reynolds Analogy ◽  
Low Reynolds Numbers ◽  
Free Stream Turbulence ◽  
High Reynolds

Measurements in a boundary layer in zero pressure gradient show that the effect of grid-generated free-stream turbulence is to increase heat transfer by about five percent for each one percent rms increase of the longitudinal intensity. In fact, even a Reynolds analogy factor, 2 × (Stanton number)/(skin-friction coefficient), increases significantly. It is suggested that the irreconcilable differences between previous measurements are attributable mainly to the low Reynolds numbers of most of those measurements. The present measurements attained a momentum-thickness Reynolds number of 6500 (chord Reynolds number approximately 6.3 × 106) and are thought to be typical of high-Reynolds-number flows.

Heat Transfer and Pressure Drop Correlations for Square Channels With V-Shaped Ribs at High Reynolds Numbers

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
Nawaf Y. Alkhamis ◽  
Akhilesh P. Rallabandi ◽  
Je-Chin Han
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Friction Factor ◽  
Thermal Performance ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Heat Transfer Coefficients ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
Rib Roughened

Heat transfer coefficients and friction factors are measured in a 45 deg V-shaped rib roughened square duct at high Reynolds numbers, pertaining to internal passages of land-based gas turbine engines. Reynolds numbers in this study range from 30,000 to 400,000, which is much higher than prior studies of V-shaped rib roughened channels. The dimensions of the channel are selected to ensure that the flow is in the incompressible regime. Blockage ratio e/D ranges from 0.1 to 0.18 and the spacing ratio P/e ranges from 5 to 10. Reported heat transfer coefficients are regionally averaged, measured by isothermal copper plates. Results show that the heat transfer enhancement decreases with increasing Reynolds number. The friction factor is found to be independent of the Reynolds number. The thermal performance decreases when the Reynolds number increases. 45 deg V-shaped ribs show a higher thermal performance than corresponding 45 deg angled ribs, consistent with the trend established in literature. Correlations for the Nusselt number and the friction factor as function of Re, e/D, and P/e are developed. Also developed are correlations for R and G (friction and heat transfer roughness functions, respectively) as a function of the roughness Reynolds number (e+).

Rib Turbulator Heat Transfer Enhancements at Very High Reynolds Numbers

2019 ◽  
Vol 11 (6) ◽  
Author(s):  
Mingyang Zhang ◽  
Prashant Singh ◽  
Srinath V. Ekkad
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Gas Turbines ◽  
Turbine Blades ◽  
Reynolds Numbers ◽  
Geometrical Parameters ◽  
High Reynolds Numbers ◽  
Rib Turbulators ◽  
High Reynolds ◽  
Very High

High-pressure stage gas turbine blades feature serpentine passages where rib turbulators are installed to enhance heat transfer between the relatively colder air bled off from the compressor and the hot internal walls. Most of the prior studies have been restricted to Reynolds number of 90,000 and several studies have been carried out to determine geometrically optimized parameters for achieving high levels of heat transfer in this range of Reynolds number. However, for land-based power generation gas turbines, the Reynolds numbers are significantly high and vary between 105 and 106. The present study is targeted toward these high Reynolds numbers where traditional rib turbulator shapes and prescribed optimum geometrical parameters have been investigated experimentally. A steady-state liquid crystal thermography technique is employed for measurement of detailed heat transfer coefficient. Five different rib configurations, viz., 45 deg, V-shaped, inverse V-shaped, W-shaped, and M-shaped have been investigated for Reynolds numbers ranging from 150,000 to 400,000. The ribs were installed on two opposite walls of a straight duct with an aspect ratio of unity. For very high Reynolds numbers, the heat transfer enhancement levels for different rib shapes varied between 1.4 and 1.7 and the thermal hydraulic performance was found to be less than unity.

Similarity Formulations for Turbulent Boundary Layers at High Reynolds Numbers

2003 ◽  
Author(s):  
Gary J. Kunkel ◽  
Ivan Marusic
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Turbulence Intensity ◽  
High Reynolds Number ◽  
Reynolds Numbers ◽  
Mean Flow ◽  
Mixed Flow ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
New Formulation

Data obtained from the high Reynolds number atmospheric boundary layer are used to analyze existing mean-flow and turbulence intensity similarity formulations. From the results of this analysis a new streamwise turbulence intensity formulation is proposed that is suggested to be applicable across the entire smooth-wall high Reynolds number turbulent boundary layer. The new formulation is also shown to be consistent with the mixed-flow scaling suggested by other studies.

Heat Transfer and Pressure Losses of W-Shaped Small Ribs at High Reynolds Numbers for Combustor Liner

2010 ◽  
Author(s):  
Tomoko Hagari ◽  
Katsuhiko Ishida ◽  
Takeo Oda ◽  
Yasushi Douura ◽  
Yasuhiro Kinoshita
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flat Plate ◽  
Pressure Loss ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
Cooling Passage ◽  
Combustor Liner ◽  
Rib Roughened

The present study investigates the heat transfer performance of W-shaped ribs in a rectangular channel with typical geometries and flow conditions for a combustor liner cooling passage. In order to assess the Reynolds number dependence on heat transfer enhancement by the ribs for the combustor cooling passage, experiments were conducted with channel Reynolds number ranging from 40,000 to 550,000. The ribs were located on one side of the channel and the rib height-to-hydraulic diameter ratio (e/Dh) was 0.006 to 0.014, which simulate the combustor liner cooling configurations. Rib pitch-to-height ratio (P/e) was 10. Rib-roughened copper plates with constant temperature were used to measure the averaged heat transfer coefficients. Measured results show that the heat transfer enhancements of about 3 were obtained over that of a flat plate at high Reynolds numbers for all cases. The slope of heat transfer coefficient becomes constant with increasing Reynolds number because of the laminar-turbulent transition around the ribs, which is considered to occur at Reynolds number based on rib height of about 1,000. Pressure loss measurements showed that the friction coefficients are constantly 3–4.5 times higher than those of a flat plate for a fully turbulent flow such as a combustor cooling passage. Pressure loss by ribs seems not to have a significant impact to the overall combustor performance. Numerical calculations were conducted additionally for all test cases. Predicted amount of heat released from the ribs contributes about 40% of overall heat release even for low ribs. Heat transfer on the rib surface is essential in the evaluation of the rib-roughened cooling passage.

Heat Transfer and Pressure Losses of W-Shaped Small Ribs at High Reynolds Numbers for Combustor Liner

2011 ◽  
Vol 133 (9) ◽  
Author(s):  
Tomoko Hagari ◽  
Katsuhiko Ishida ◽  
Takeo Oda ◽  
Yasushi Douura ◽  
Yasuhiro Kinoshita
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Flat Plate ◽  
Pressure Loss ◽  
Reynolds Numbers ◽  
High Reynolds Numbers ◽  
High Reynolds ◽  
Cooling Passage ◽  
Combustor Liner ◽  
Rib Roughened

The present study investigates the heat transfer performance of W-shaped ribs in a rectangular channel with typical geometries and flow conditions for a combustor liner cooling passage. In order to assess the Reynolds number dependence on heat transfer enhancement by the ribs for the combustor cooling passage, experiments were conducted with channel Reynolds number ranging from 40,000 to 550,000. The ribs were located on one side of the channel and the rib height-to-hydraulic diameter ratio (e/Dh) was 0.006–0.014, which simulate the combustor liner cooling configurations. Rib pitch-to-height ratio (P/e) was 10. Rib-roughened copper plates with constant temperature were used to measure the averaged heat transfer coefficients. Measured results show that the heat transfer enhancements of about 3 were obtained over that of a flat plate at high Reynolds numbers for all cases. The slope of heat transfer coefficient becomes constant with increasing Reynolds number because of the laminar-turbulent transition around the ribs, which is considered to occur at Reynolds number based on rib height of about 1000. Pressure loss measurements showed that the friction coefficients are constantly 3–4.5 times higher than those of a flat plate for a fully turbulent flow such as a combustor cooling passage. Pressure loss by ribs seems not to have a significant impact to the overall combustor performance. Numerical calculations were conducted additionally for all test cases. Predicted amount of heat released from the ribs contributes about 40% of the overall heat release even for low ribs. Heat transfer on the rib surface is essential in the evaluation of the rib-roughened cooling passage.

An Experimental and Numerical Study of Heat Transfer and Pressure Loss in a Rectangular Channel With V-Shaped Ribs

2006 ◽  
Author(s):  
Michael Maurer ◽  
Jens von Wolfersdorf ◽  
Michael Gritsch
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Thermal Performance ◽  
Pressure Loss ◽  
Numerical Study ◽  
Rectangular Channel ◽  
Reynolds Numbers ◽  
Transfer Enhancement ◽  
High Reynolds Numbers ◽  
High Reynolds

An experimental and numerical study was conducted to determine the thermal performance of V-shaped ribs in a rectangular channel with an aspect ratio of 2:1. Local heat transfer coefficients were measured using the steady state thermochromic liquid crystal technique. Periodic pressure losses were obtained with pressure taps along the smooth channel sidewall. Reynolds numbers from 95,000 to 500,000 were investigated with V-shaped ribs located on one side or on both sides of the test channel. The rib height-to-hydraulic diameter ratios (e/Dh) were 0.0625 and 0.02, and the rib pitch-to-height ratio (P/e) was 10. In addition, all test cases were investigated numerically. The commercial software FLUENT™ was used with a two-layer k-ε turbulence model. Numerically and experimentally obtained data were compared. It was determined that the heat transfer enhancement based on the heat transfer of a smooth wall levels off for Reynolds numbers over 200,000. The introduction of a second ribbed sidewall slightly increased the heat transfer enhancement whereas the pressure penalty was approximately doubled. Diminishing the rib height at high Reynolds numbers had the disadvantage of a slightly decreased heat transfer enhancement, but benefits in a significantly reduced pressure loss. At high Reynolds numbers small-scale ribs in a one-sided ribbed channel were shown to have the best thermal performance.

The Effect of Pulsed Blowing on the Boundary Layer of a Highly Loaded Low Pressure Turbine Blade

2013 ◽  
Author(s):  
Marion Mack ◽  
Roland Brachmanski ◽  
Reinhard Niehuis
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Mach Number ◽  
Suction Side ◽  
Reynolds Numbers ◽  
Low Pressure ◽  
Trailing Edge ◽  
Low Pressure Turbine ◽  
Wide Range ◽  
Highly Loaded

The performance of the low pressure turbine (LPT) can vary appreciably, because this component operates under a wide range of Reynolds numbers. At higher Reynolds numbers, mid and aft loaded profiles have the advantage that transition of suction side boundary layer happens further downstream than at front loaded profiles, resulting in lower profile loss. At lower Reynolds numbers, aft loading of the blade can mean that if a suction side separation exists, it may remain open up to the trailing edge. This is especially the case when blade lift is increased via increased pitch to chord ratio. There is a trend in research towards exploring the effect of coupling boundary layer control with highly loaded turbine blades, in order to maximize performance over the full relevant Reynolds number range. In an earlier work, pulsed blowing with fluidic oscillators was shown to be effective in reducing the extent of the separated flow region and to significantly decrease the profile losses caused by separation over a wide range of Reynolds numbers. These experiments were carried out in the High-Speed Cascade Wind Tunnel of the German Federal Armed Forces University Munich, Germany, which allows to capture the effects of pulsed blowing at engine relevant conditions. The assumed control mechanism was the triggering of boundary layer transition by excitation of the Tollmien-Schlichting waves. The current work aims to gain further insight into the effects of pulsed blowing. It investigates the effect of a highly efficient configuration of pulsed blowing at a frequency of 9.5 kHz on the boundary layer at a Reynolds number of 70000 and exit Mach number of 0.6. The boundary layer profiles were measured at five positions between peak Mach number and the trailing edge with hot wire anemometry and pneumatic probes. Experiments were conducted with and without actuation under steady as well as periodically unsteady inflow conditions. The results show the development of the boundary layer and its interaction with incoming wakes. It is shown that pulsed blowing accelerates transition over the separation bubble and drastically reduces the boundary layer thickness.

Sign in / Sign up

Export Citation Format

Share Document