The grain-boundary sliding component in high-temperature fatigue

1980 ◽  
Vol 15 (3) ◽  
pp. 795-796 ◽  
Author(s):  
K. U. Snowden
Keyword(s):  
High Temperature ◽  
Grain Boundary ◽  
Grain Boundary Sliding ◽  
High Temperature Fatigue ◽  
Boundary Sliding

Grain boundary sliding at high temperature deformation in cold-rolled ODS ferritic steels

2014 ◽  
Vol 452 (1-3) ◽  
pp. 628-632 ◽  
Author(s):  
Yoshito Sugino ◽  
Shigeharu Ukai ◽  
Bin Leng ◽  
Naoko Oono ◽  
Shigenari Hayashi ◽  
...  
Keyword(s):  
High Temperature ◽  
Grain Boundary ◽  
Grain Boundary Sliding ◽  
High Temperature Deformation ◽  
Temperature Deformation ◽  
Ferritic Steels ◽  
Boundary Sliding ◽  
Cold Rolled

High-temperature grain boundary sliding behavior and grain boundary energy in cubic zirconia bicrystals

2004 ◽  
Vol 52 (8) ◽  
pp. 2349-2357 ◽  
Author(s):  
Hidehiro Yoshida ◽  
Kenji Yokoyama ◽  
Naoya Shibata ◽  
Yuichi Ikuhara ◽  
Taketo Sakuma
Keyword(s):  
High Temperature ◽  
Grain Boundary ◽  
Boundary Energy ◽  
Grain Boundary Sliding ◽  
Grain Boundary Energy ◽  
Cubic Zirconia ◽  
Boundary Sliding

Evaluation of Plastic Workability Limit of Magnesium Alloy by Cavitations in High Temperature Uni and Biaxial Test

2012 ◽  
Vol 735 ◽  
pp. 67-72
Author(s):  
Kunio Funami ◽  
Daisuke Yamashita ◽  
Kohji Suzuki ◽  
Masafumi Noda
Keyword(s):  
Fine Structure ◽  
High Temperature ◽  
Magnesium Alloy ◽  
Grain Boundary ◽  
Room Temperature ◽  
Grain Boundary Sliding ◽  
Az31 Magnesium Alloy ◽  
Temperature Deformation ◽  
Alloy Plate ◽  
Boundary Sliding

Abstract. This study examined the critical plastic formability limit of a fine-structure AZ31 magnesium alloy plate under warm and high temperature based on the strength of a magnesium alloy that has cavities at room temperature. The cyclic hot free-forging process as pre-form working following rolling at a light reduction ratio fabricated a fine-structure AZ31 magnesium alloy plate. The appearance of the cavities was examined in detail together with changes in the structure and preparation methods before further damage at high temperatures with increasing uni-and biaxial plastic deformation. The allowable deformation limit in the super plasticity process can be estimated from the strength of the deformed material and forming limit diagram (FLD) at room temperature. During high-temperature deformation, cavities are produced by stress concentrations at grain boundary triple points and striation bands due to grain boundary sliding. The cavitations growth behavior is dependent upon deformation conditions, and a high percentage of large cavities occupy the sample surface as a large amount of grain boundary sliding is present, i.e., as uniform elongation grows larger, the cavity size also increases. In a case where 200% uniaxial strain was applied to a fine-grained structure material at a temperature of 623K under a strain rate of 10-4s-1, the tensile strength at room temperature decreased about 13%, and elongation was 10% less, compared with that of a material to which no load was applied due to the influence of cavities. In a case of biaxial deformation, the values were 28% lower. It is possible to draw a FLD based on the cavity incidence fraction .

Impression Creep Behavior of Atmospheric Plasma-Sprayed and Hot Pressed MoSi2/Si3N4

1997 ◽  
Author(s):  
K.J. Hollis ◽  
D.P. Butt ◽  
R.G. Castro
Keyword(s):  
High Temperature ◽  
Grain Boundary ◽  
Creep Behavior ◽  
Grain Boundary Sliding ◽  
Atmospheric Plasma ◽  
Second Phase ◽  
Impression Creep ◽  
Creep Mechanisms ◽  
Boundary Sliding ◽  
Plasma Sprayed

Abstract The use of MoSi2 as a high temperature oxidation resistant structural material is hindered by its poor elevated temperature creep resistance. The addition of second phase Si3N4 holds promise for improving the creep properties of MoSi2 without decreasing oxidation resistance. The high temperature impression creep behavior of atmospheric plasma sprayed (APS) and hot pressed (HP) MoSi2/Si3N4 composites was investigated. Values for steady state creep rates, creep activation energies, and creep stress exponents were measured. Grain boundary sliding and splat sliding were found to be the dominant creep mechanisms for the APS samples while grain boundary sliding and plastic deformation were found to be the dominant creep mechanisms for the HP samples.

Sign in / Sign up

Export Citation Format

Share Document