The mechanics of the vertical drawing process

1962 ◽  
Vol 19 (1) ◽  
pp. 7-14
Author(s):  
K. I. Braginskii
Keyword(s):  
Vertical Drawing ◽  
Drawing Process

scholarly journals Numerical investigation of the effect of punch corner radius and die shoulder radius on the flange earrings for AA1050 and AA1100 aluminum alloys in cylindrical deep drawing process

Heliyon ◽  
2021 ◽  
Vol 7 (4) ◽  
pp. e06662
Author(s):  
K. Bouchaâla ◽  
M.F. Ghanameh ◽  
M. Faqir ◽  
M. Mada ◽  
E. Essadiqi
Keyword(s):  
Aluminum Alloys ◽  
Numerical Investigation ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Corner Radius

scholarly journals Effect of Tool Geometry Parameters on the Formability of a Camera Cover in the Deep Drawing Process

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3993
Author(s):  
Thanh Trung Do ◽  
Pham Son Minh ◽  
Nhan Le
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Metal Flow ◽  
Sheet Thickness ◽  
Side Wall ◽  
Tool Geometry ◽  
Drawing Process ◽  
Nose Radius ◽  
Deep Drawing Process

The formability of the drawn part in the deep drawing process depends not only on the material properties, but also on the equipment used, metal flow control and tool parameters. The most common defects can be the thickening, stretching and splitting. However, the optimization of tools including the die and punch parameters leads to a reduction of the defects and improves the quality of the products. In this paper, the formability of the camera cover by aluminum alloy A1050 in the deep drawing process was examined relating to the tool geometry parameters based on numerical and experimental analyses. The results showed that the thickness was the smallest and the stress was the highest at one of the bottom corners where the biaxial stretching was the predominant mode of deformation. The problems of the thickening at the flange area, the stretching at the side wall and the splitting at the bottom corners could be prevented when the tool parameters were optimized that related to the thickness and stress. It was clear that the optimal thickness distribution of the camera cover was obtained by the design of tools with the best values—with the die edge radius 10 times, the pocket radius on the bottom of the die 5 times, and the punch nose radius 2.5 times the sheet thickness. Additionally, the quality of the camera cover was improved with a maximum thinning of 25% experimentally, and it was within the suggested maximum allowable thickness reduction of 45% for various industrial applications after optimizing the tool geometry parameters in the deep drawing process.

Blank shape optimization in the deep drawing process by sun method

2021 ◽  
Author(s):  
Hamidreza Gharehchahi ◽  
Mohammad Javad Kazemzadeh-Parsi ◽  
Ahmad Afsari ◽  
Mehrdad Mohammadi
Keyword(s):  
Shape Optimization ◽  
Deep Drawing ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Blank Shape Optimization ◽  
Blank Shape

Production of Tapered Cups by Sequential Deep Drawing of Sheet Metals Using Drawn Cups as a Part of Punch

1993 ◽  
Vol 115 (2) ◽  
pp. 224-229 ◽  
Author(s):  
K. Yamaguchi ◽  
K. Kanayama ◽  
M. H. Parsa ◽  
N. Takakura
Keyword(s):  
Deep Drawing ◽  
Drawing Ratio ◽  
Drawing Process ◽  
Sheet Metals ◽  
Deep Drawing Process ◽  
Drawing Method

A new deep drawing process of sheet metals is developed to facilitate small-lot production of deep cups with large drawing ratio. In this process, unlike the conventional deep drawing method, a few drawn cups are always stacked on the punch and used as a part of punch for the subsequent deep drawing of a given blank. Before drawing a new blank, a drawn cup which is in contact with the punch is stripped off. The repetition of such stripping and drawing operations makes it possible to carry out both the first-stage drawing and the subsequent slight redrawings in one drawing operation using only one pair of punch and die. In this paper, this new deep drawing process is applied to the production of tapered cups and the main feature of the process is shown.

An Investigation of the Plug Drawing Process

1960 ◽  
Vol 174 (1) ◽  
pp. 797-812 ◽  
Author(s):  
T. Z. Blazynski ◽  
I. M. Cole
Keyword(s):  
Drawing Process

Shop Drawing Process of Stone Veneered Cladding Systems

1997 ◽  
Vol 3 (2) ◽  
pp. 70-79 ◽  
Author(s):  
Roberto Pietroforte
Keyword(s):  
Drawing Process ◽  
Shop Drawing

Determination of optimum process parameters for wrinkle free products in deep drawing process

2007 ◽  
Vol 191 (1-3) ◽  
pp. 51-54 ◽  
Author(s):  
Anupam Agrawal ◽  
N. Venkata Reddy ◽  
P.M. Dixit
Keyword(s):  
Process Parameters ◽  
Deep Drawing ◽  
Optimum Process ◽  
Drawing Process ◽  
Free Products ◽  
Deep Drawing Process

Design and research of a novel type of mechanical presses driven by three servo motors in parallel

2012 ◽  
Vol 227 (3) ◽  
pp. 580-591 ◽  
Author(s):  
Xun Huang ◽  
Chunxiang Ma ◽  
Suxing Wu ◽  
Qian Wang ◽  
Zhibo Wang ◽  
...  
Keyword(s):  
Probability Theory ◽  
Forward Kinematics ◽  
Generalized Function ◽  
Engineering Practice ◽  
Drawing Process ◽  
Fuzzy Probability ◽  
Fuzzy Reliability ◽  
Deep Drawing Process ◽  
Computing Method ◽  
Fuzzy Probability Theory

A novel type of mechanical presses design driven by three servo motors in parallel is proposed to develop high stamping capacity based on the theory of generalized function sets, and then is improved to enhance its practicability in engineering practice. The inverse and forward kinematics analyses are conducted later. Based on the fuzzy probability theory, the computing method of fuzzy reliability of kinematic accuracy of slider is then obtained. Finally, with a set of optimized length parameters of the presses given, the fuzzy reliability is calculated, on the basis of which a typical deep-drawing process is simulated.

Sign in / Sign up

Export Citation Format

Share Document