Determination of the optimal temperature program regime in the production of dibasole (exchange of experience)

1978 ◽  
Vol 12 (10) ◽  
pp. 1389-1393
Author(s):  
N. N. Bochkov ◽  
Yu. P. Stepnykh
Keyword(s):  
Optimal Temperature ◽  
Temperature Program

Determination of Optimal Temperature for Defect-Free Casting of Aluminium in the LP-LFC Process

2011 ◽  
Vol 101-102 ◽  
pp. 934-937
Author(s):  
Ji Qiang Li ◽  
Zhong Zhao ◽  
Zi Tian Fan ◽  
Zhi Xin Jia ◽  
Wen Liu ◽  
...  
Keyword(s):  
Energy Consumption ◽  
Aluminium Alloys ◽  
Low Pressure ◽  
Experimental Results ◽  
Metal Temperature ◽  
Lost Foam Casting ◽  
Optimal Temperature ◽  
Pouring Temperature ◽  
Lost Foam

Fluidity of ZL101 aluminium alloys in the low-pressure lost foam casting (LP-LFC) process has been investigated by altering various temperature variables. The experimental results indicate that the LP-LFC process had fine fluidity, and the pouring temperature was lower than conventional lost foam casting. The effect of the metal temperature on the fluidity is marginal in the LP-LFC process. Excessive pouring temperature not only aggrandizes energy consumption but also deteriorates porosity defect. The success of casting cooling fin demonstrates the advantages of LP-EPC process in producing high-complicated castings.

Determination of diffusion coefficients with a general temperature program using dta equipment

1983 ◽  
Vol 64 (1-2) ◽  
pp. 229-236 ◽  
Author(s):  
P. Kubíček ◽  
B. Wozniaková ◽  
J. Leško
Keyword(s):  
Diffusion Coefficients ◽  
Temperature Program

Determination of the optimal temperature and consumption of oxygen in rearing young australian red clawed crayfish

2017 ◽  
pp. 121-128
Author(s):  
A.V. Zhigin ◽  
◽  
V.A. Arystangaliyeva ◽  
D.V. Tyrin ◽  
N.P. Kovacheva ◽  
...  
Keyword(s):  
Optimal Temperature

scholarly journals Determinación de la producción de jalea real en colmenas de recría de diferentes dimensiones

2007 ◽  
Vol 8 (1) ◽  
pp. 75
Author(s):  
Hugo Humberto Ballesteros ◽  
Rodrigo Efrén Vásquez
Keyword(s):  
Minimum Temperature ◽  
Royal Jelly ◽  
The Other ◽  
Optimal Temperature ◽  
Internal Temperature ◽  
Tropical Ecosystem ◽  
Average Production ◽  
Optimal Temperature Range ◽  
Different Dimensions

<p>Se valoró la producción de jalea real en un apiario localizado en un ecosistema de trópico alto. A tal fin, se evaluaron cuatro tratamientos representados en colmenas de recría de diez, ocho y seis cuadros, cada uno con tres repeticiones; se estimó el porcentaje de aceptación y la cantidad de jalea real por cúpula. En las colmenas de recría de seis cuadros la temperatura interna fue más constante que en los demás tratamientos (mínima 30°C y máxima 38°C); así mismo, presentó un rango de temperatura óptima entre 34 y 35°C, factor de gran importancia ya que este tipo de colmena de recría produjo la mayor cantidad de jalea real por transferencia (15.973 mg) con una aceptación de cúpulas del 86,3% y una producción promedio por cúpula aceptada de 308,5 mg. Las colmenas de recría de ocho cuadros presentaron una temperatura mínima de 26°C y una máxima de 36°C, con una producción de 7.976 mg por transferencia, una aceptación del 72% y una producción promedio por cúpula aceptada de 185,3 mg. Las colmenas de recría de diez cuadros presentaron una temperatura mínima de 22°C y una máxima de 34°C, una producción de 6.364 mg por transferencia, una aceptación del 51% y una producción promedio por cúpula aceptada de 208 mg.</p><p> </p><p><strong>Determination of royal jelly production in rearing hives of different dimensions</strong></p><p>The production of royal jelly in an apiary located in a high tropical ecosystem was evaluated. To that end, four treatments were evaluated represented in rearing hives of ten, eight and six compartments, each with three repetitions; the percentage of filled cupules and the quantity of royal jelly per cupule for each group was determined. In the rearing hives with six compartments the internal temperature was more constant than in the other treatments (minimum 30°C and maximum 38°C); it also showed an optimal temperature range of 34-35ºC, a factor of great importance since this kind of rearing hive produced the largest amount of royal jelly per transfer (15,973 mg) with 86.3% of filled cupules and an average production of 308.5 mg per filled cupule. The rearing hives with eight compartments showed a minimum temperature of 26°C and maximum of 36°C, with a production of 7,976 mg per transfer, 72% filled cupules and an average production of 185.3 mg per filled cupule. The rearing hives of ten compartments showed a minimum temperature of 22°C and a maximum of 34°C, with a production of 6,364 mg per transfer, 51% filled cupules and an average production of 208 mg per filled cupule.</p>

Sign in / Sign up

Export Citation Format

Share Document