Elastic deformation and slippage of layers of a rolled cylindrical shell due to loading by an internal pressure

1981 ◽  
Vol 17 (6) ◽  
pp. 546-549 ◽  
Author(s):  
L. A. Il'in ◽  
N. A. Lobkova
Keyword(s):  
Cylindrical Shell ◽  
Internal Pressure ◽  
Elastic Deformation

scholarly journals Strain Growth in a Finite-Length Cylindrical Shell Under Internal Pressure Pulse

2017 ◽  
Vol 139 (2) ◽  
Author(s):  
Qi Dong ◽  
Q. M. Li ◽  
Jinyang Zheng
Keyword(s):  
Cylindrical Shell ◽  
Boundary Conditions ◽  
Internal Pressure ◽  
Finite Length ◽  
Pressure Pulse ◽  
Elastic Response ◽  
Local Dynamic ◽  
Growth Phenomenon ◽  
Modal Coupling ◽  
Elastic Responses

Strain growth is a phenomenon observed in the elastic response of containment vessels subjected to internal blast loading. The local dynamic response of a containment vessel may become larger in a later stage than its response in the earlier stage. In order to understand the possible mechanisms of the strain growth phenomenon in a cylindrical vessel, dynamic elastic responses of a finite-length cylindrical shell with different boundary conditions subjected to internal pressure pulse are studied by finite-element simulation using LS-DYNA. It is found that the strain growth in a finite-length cylindrical shell with sliding–sliding boundary conditions is caused by nonlinear modal coupling. Strain growth in a finite-length cylindrical shell with free–free or simply supported boundary conditions is primarily caused by the linear modal superposition, possibly enhanced by the nonlinear modal coupling. The understanding of these strain growth mechanisms can guide the design of cylindrical containment vessels.

scholarly journals Structural Design for a 10-GWh SMES Vacuum Vessel

1978 ◽  
Vol 100 (3) ◽  
pp. 263-270
Author(s):  
J. G. Bennett ◽  
C. A. Anderson
Keyword(s):  
Cylindrical Shell ◽  
Approximate Solution ◽  
Elastic Deformation ◽  
Material Properties ◽  
Structural Design ◽  
Shell Thickness ◽  
Construction Cost ◽  
Vacuum Vessel ◽  
Nonlinear Elastic

An approximate solution to the problem of the nonlinear elastic deformation of a periodically point-supported cylindrical shell is obtained. This solution is used to investigate the structural design of the vacuum vesssel for the large underground SMES concept. Vacuum vessel designs are evaluated by varying such parameters as shell thickness, support, spacing, material properties and physical configuration to keep the amount of material used and construction cost to a minimum.

Design Equation for Minimum Required Thickness of a Cylindrical Shell Subject to Internal Pressure Based on Von Mises Criterion

2019 ◽  
Author(s):  
James Lu ◽  
Barry Millet ◽  
Kenneth Kirkpatrick ◽  
Bryan Mosher
Keyword(s):  
Cylindrical Shell ◽  
Internal Pressure ◽  
Yield Criterion ◽  
Design Equation ◽  
Shell Wall ◽  
Section Viii ◽  
Von Mises Yield Criterion ◽  
Von Mises ◽  
Division 2 ◽  
Shell Wall Thickness

Abstract Design equation (4.3.1) for the minimum required thickness of a cylindrical shell subjected to internal pressure in Part 4 “design by rule (DBR)” of the ASME Boiler and Pressure Vessel Code, Section VIII, Division 2 [1] is based on the Tresca Yield Criterion, while design by analysis (DBA) in Part 5 of the Division 2 Code is based on the von Mises Yield Criterion. According to ASME PTB-1 “ASME Section VIII – Division 2 Criteria and Commentary”, the difference in results is about 15% due to use of the two different criteria. Although the von Mises Yield Criterion will result in a shell wall thickness less than that from Tresca Yield Criterion, Part 4 (DBR) of ASME Division 2 adopts the latter for a more convenient design equation. To use the von Mises Criterion in lieu of Tresca to reduce shell wall thickness, one has to follow DBA rules in Part 5 of Division 2, which typically requires detailed numeric analysis performed by experienced stress analysts. This paper proposes a simple design equation for the minimum required thickness of a cylindrical shell subjected to internal pressure based on the von Mises Yield Criterion. The equation is suitable for both thin and thick cylindrical shells. Calculation results from the equation are validated by results from limit load analyses in accordance with Part 5 of ASME Division 2 Code.

Free Vibration and Elastic Critical Load of Functionally Graded Material Thin Cylindrical Shells Under Internal Pressure

2018 ◽  
Vol 18 (11) ◽  
pp. 1850138 ◽  
Author(s):  
Yueyang Han ◽  
Xiang Zhu ◽  
Tianyun Li ◽  
Yunyan Yu ◽  
Xiaofang Hu
Keyword(s):  
Cylindrical Shell ◽  
Free Vibration ◽  
Internal Pressure ◽  
Critical Load ◽  
Natural Frequency ◽  
Functionally Graded Material ◽  
Present Method ◽  
Cylindrical Shells ◽  
Functionally Graded ◽  
Graded Material

An analytical approach for predicting the free vibration and elastic critical load of functionally graded material (FGM) thin cylindrical shells filled with internal pressured fluid is presented in this study. The vibration of the FGM cylindrical shell is described by the Flügge shell theory, where the internal static pressure is considered as the prestress term in the shell equations. The motion of the internal fluid is described by the acoustic wave equation. The natural frequencies of the FGM cylindrical shell under different internal pressures are obtained with the wave propagation method. The relationship between the internal pressure and the natural frequency of the cylindrical shell is analyzed. Then the linear extrapolation method is employed to obtain the elastic critical load of the FGM cylindrical shell from the condition that the increasing pressure has resulted in zero natural frequency. The accuracy of the present method is verified by comparison with the published results. The effects of gradient index, boundary conditions and structural parameters on the elastic critical load of the FGM cylindrical shell are discussed. Compared with the experimental and numerical analyses based on the external pressure, the present method is simple and easy to carry out.

Deformation of a supported short cylindrical shell of aluminum alloy under internal pressure

1970 ◽  
Vol 6 (7) ◽  
pp. 975-993 ◽  
Author(s):  
Y. Ohashi ◽  
N. Kamiya
Keyword(s):  
Cylindrical Shell ◽  
Aluminum Alloy ◽  
Internal Pressure

Effect of internal pressure on an infinite cylindrical shell subjected to concentrated radial loads

AIAA Journal ◽  
1969 ◽  
Vol 7 (10) ◽  
pp. 1944-1949 ◽  
Author(s):  
PAUL SEIDE
Keyword(s):  
Cylindrical Shell ◽  
Internal Pressure ◽  
Infinite Cylindrical Shell
Sign in / Sign up

Export Citation Format

Share Document