Effect of reactor radiations on the creep resistance and long-time strength of austenitic stainless steel 0Kh16N15M3B

1974 ◽  
Vol 6 (4) ◽  
pp. 399-404 ◽  
Author(s):  
G. S. Pisarenko ◽  
V. N. Kiselevskii ◽  
D. V. Polevoi ◽  
V. K. Lukashev ◽  
V. A. Tsykanov ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Creep Resistance ◽  
Steel 0Kh16n15m3b ◽  
Long Time ◽  
Time Strength

Precipitation during long time ageing in the austenitic stainless steel 310

2012 ◽  
Vol 29 (1) ◽  
pp. 8-16 ◽  
Author(s):  
Rolf Sandström ◽  
Muhammad Farooq ◽  
Mats Lundberg
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Long Time ◽  
Stainless Steel 310

Creep property measurement of service-exposed SUS 316 austenitic stainless steel by the small-punch creep-testing technique

2002 ◽  
Vol 17 (8) ◽  
pp. 1945-1953 ◽  
Author(s):  
Maribel L. Saucedo-Muñoz ◽  
Shin-Ichi Komazaki ◽  
Toru Takahashi ◽  
Toshiyuki Hashida ◽  
Tetsuo Shoji
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Creep Test ◽  
Creep Resistance ◽  
Creep Property ◽  
Creep Rupture ◽  
Secondary Creep ◽  
Small Punch ◽  
Uniaxial Creep ◽  
Small Punch Creep Test

The creep properties for SUS 316 HTB austenitic stainless steel were evaluated by using the small-punch creep test at 650 °C for loads of 234, 286, 338, 408, and 478 N and at 700 °C for loads of 199 and 234 N. The creep curves, determined by means of the small-punch creep test, were similar to those obtained from a conventional uniaxial creep test. That is, they exhibited clearly the three creep stages. The width of secondary creep stage and rupture time tr decreased with the increase in testing load level. The creep rupture strength for the service-exposed material was lower than that of the as-received material at high testing loads. However, the creep resistance behavior was opposite at relatively low load levels. This difference in creep resistance was explained on the basis of the difference in the creep deformation and microstructural evolution during tests. It was also found that the ratio between the load of small-punch creep test and the stress of uniaxial creep test was about 1 for having the same value of creep rupture life.

Improved creep-resistance of austenitic stainless steel for compact gas turbine recuperators

1999 ◽  
Vol 16 (4) ◽  
pp. 207-212 ◽  
Author(s):  
P.J. Maziasz ◽  
R.W. Swindeman ◽  
J.P. Montague ◽  
M. Fitzpatrick ◽  
P.F. Browning ◽  
...  
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Gas Turbine ◽  
Creep Resistance

?Neitron-11? apparatus for investigating the effect of reactor radiation on the creep resistance and long-time strength of structural materials in a complex stressed state

1982 ◽  
Vol 14 (4) ◽  
pp. 560-565
Author(s):  
G. S. Pisarenko ◽  
A. P. Voloshchenko ◽  
V. K. Lukashev ◽  
Yu. A. Kuzema ◽  
M. M. Aleksyuk ◽  
...  
Keyword(s):  
Stressed State ◽  
Creep Resistance ◽  
Structural Materials ◽  
Complex Stressed State ◽  
Reactor Radiation ◽  
Long Time ◽  
Time Strength

Precipitation during long time ageing in the austenitic stainless steel 310

2012 ◽  
Vol 29 (1) ◽  
pp. 8-16 ◽  
Author(s):  
Muhammad Farooq ◽  
Rolf Sandström ◽  
Mats Lundberg
Keyword(s):  
Stainless Steel ◽  
Austenitic Stainless Steel ◽  
Long Time ◽  
Stainless Steel 310

SIRIUS S12

Alloy Digest ◽  
2004 ◽  
Vol 53 (10) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
High Temperature ◽  
Austenitic Stainless Steel ◽  
Physical Properties ◽  
Carbon Content ◽  
Tensile Properties ◽  
Creep Resistance ◽  
Heat Treating ◽  
Temperature Performance

Abstract Sirius S12 is an austenitic stainless steel for high-temperature service. The carbon content is optimized for creep resistance, and the alloy contains additions of silicon to outperform the conventional grades in oxidation. This datasheet provides information on composition, physical properties, elasticity, and tensile properties as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming and heat treating. Filing Code: SS-910. Producer or source: Industeel USA, LLC.

SIRIUS 800-H-H+

Alloy Digest ◽  
2013 ◽  
Vol 62 (11) ◽  
Keyword(s):  
Stainless Steel ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Austenitic Stainless Steel ◽  
Tensile Properties ◽  
Creep Resistance ◽  
Heat Treating ◽  
Temperature Performance

Abstract Sirius 800, H, and H+ are three variants of an austenitic stainless steel for high temperature service. It has both oxidation and creep resistance. This datasheet provides information on composition, elasticity, tensile properties, and shear strength as well as creep. It also includes information on high temperature performance and corrosion resistance as well as forming, heat treating, and joining. Filing Code: SS-1162. Producer or source: Industeel USA, LLC.

Sign in / Sign up

Export Citation Format

Share Document