Evolution of microstructure, mechanical properties, electrochemical behaviour and thermal stability of Ti0.25-Al0.2-Mo0.2-Si0.25W0.1 high entropy alloy fabricated by spark plasma sintering technique

2019 ◽  
Vol 104 (5-8) ◽  
pp. 3163-3171
Author(s):  
L. R. Kanyane ◽  
N. Malatji ◽  
A. P. I. Popoola ◽  
M. B. Shongwe
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Spark Plasma Sintering ◽  
Electrochemical Behaviour ◽  
High Entropy Alloy ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma ◽  
Evolution Of Microstructure ◽  
Thermal Stability Of

Wear and mechanical properties of novel (CuCrFeTiZn)100-xPbx high entropy alloy composite via mechanical alloying and spark plasma sintering

Wear ◽  
2018 ◽  
Vol 410-411 ◽  
pp. 93-109 ◽  
Author(s):  
Surekha Yadav ◽  
S. Sarkar ◽  
Akash Aggarwal ◽  
Arvind Kumar ◽  
Krishanu Biswas
Keyword(s):  
Mechanical Properties ◽  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
High Entropy Alloy ◽  
Alloy Composite ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma

Non-equiatomic W10Mo27Cr21Ti22Al20 high-entropy alloy produced by mechanical alloying and spark plasma sintering: Phase evolution and mechanical properties

2022 ◽  
pp. 146442072110510
Author(s):  
Hamed Naser-Zoshki ◽  
Ali-Reza Kiani-Rashid ◽  
Jalil Vahdati-Khaki
Keyword(s):  
Mechanical Properties ◽  
Solid Solution ◽  
Mechanical Alloying ◽  
Spark Plasma Sintering ◽  
Elevated Temperatures ◽  
High Entropy Alloy ◽  
Solid Solution Phase ◽  
High Entropy ◽  
Plasma Sintering ◽  
Spark Plasma

In this work, non-equiatomic W10Mo27Cr21Ti22Al20 refractory high-entropy alloy (RHEA) was produced using mechanical alloying followed by spark plasma sintering. The phase formation, microstructure, and compressive mechanical properties of the alloy were studied. During mechanical alloying, a Body-centered cubic (BCC) solid solution phase with a particle size of less than 1 µm was obtained after 18 h ball milling. The microstructure of the sintered sample exhibits three distinct phases consisting of two solid solution phases BCC1 and BCC2 as well as fine TiCxOy precipitates distributed in them. The volume fractions of each phase were about 79%, 8%, and 13%, respectively. The sintered W10Mo27Cr21Ti22Al20 showed yield strengths of 2465, 1506, 405, and 290 MPa at room temperature 600, 1000, and 1200°C, respectively, which are about twice that of the same refractory high-entropy alloy produced by vacuum arc melting. At 1000 and 1200°C, the strength after yielding gradually increased to 970 and 718 MPa at a compressive strain of 60%. The studied refractory high-entropy alloy can have good potential in high-temperature applications due to its high specific strength at elevated temperatures compared to conventional Ni-based superalloys and most as-reported refractory high-entropy alloys.

Sign in / Sign up

Export Citation Format

Share Document