Finite element analysis and experiment on viscous warm pressure bulging of AZ31B magnesium alloy

2017 ◽  
Vol 32 (3) ◽  
pp. 640-644 ◽  
Author(s):  
Tiejun Gao ◽  
Wenzhuo Zhang ◽  
Menglong Xu ◽  
Zhongjin Wang
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Element Analysis ◽  
Az31b Magnesium Alloy

Finite Element Analysis on Optimized Condition of Super Plastic Forming of AZ31B Magnesium Alloy Sheets

2017 ◽  
Vol 4 (6) ◽  
pp. 6678-6687
Author(s):  
K. Sathish ◽  
S.T. Selvamani ◽  
P. Ramesh ◽  
D. Sivakumar ◽  
M. Vigneshwar ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Element Analysis ◽  
Az31b Magnesium Alloy ◽  
Super Plastic ◽  
Plastic Forming ◽  
Super Plastic Forming

scholarly journals Simulation and finite element analysis of continuous multi-pass hot rolled AZ31B magnesium alloy sheets

2012 ◽  
Vol 50 (01) ◽  
pp. 43-49
Author(s):  
K. YU ◽  
Z. Y. CAI ◽  
X. TAN ◽  
F. W. CHEN ◽  
Y. N. HU ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Element Analysis ◽  
Az31b Magnesium Alloy ◽  
Hot Rolled

scholarly journals A Study on Designing Balloon Expandable Magnesium Alloy Stent for Optimization of Mechanical Characteristics

Proceedings ◽  
2018 ◽  
Vol 2 (8) ◽  
pp. 523
Author(s):  
Ichiro Shimizu ◽  
Akira Wada ◽  
Makoto Sasaki
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Magnesium Alloys ◽  
Study Design ◽  
Mechanical Characteristics ◽  
Design Parameters ◽  
Optimized Design ◽  
Element Analysis ◽  
Biodegradable Properties

Recently, the demand for a bio-absorbable coronary stent to promote recovery after an operation has increased. An option for such a stent is one made of a magnesium alloy, which has biodegradable properties. However, magnesium alloys have lower rigidity and lower ductility than other metals; as such, an appropriate stent structure is required to ensure radial rigidity. In this study, design parameters for an AZ31 magnesium alloy stent with sufficient radial rigidity were investigated. The necessary radial rigidity was determined by comparison tests against commercially available stents. The design parameters of the cell struts were selected and the optimum values to achieve high radial rigidity were investigated by means of elastic–plastic finite element analysis. Finally, a trial model stent based on the optimized design parameters was produced. It was confirmed that the model had sufficient radial rigidity, with no fracturing evident during crimping and expansion processes.

418 Cold roll forming process of wrought magnesium alloy using finite element analysis

2014 ◽  
Vol 2014.22 (0) ◽  
pp. 163-164
Author(s):  
Shintaro AKANUMA ◽  
Tomoya SUZUKI ◽  
Hayato ASO ◽  
Bunkyo KYO ◽  
Shinichi NISHIDA ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Magnesium Alloy ◽  
Roll Forming ◽  
Cold Roll Forming ◽  
Forming Process ◽  
Element Analysis ◽  
Cold Roll ◽  
Wrought Magnesium Alloy ◽  
Roll Forming Process

FORMING LIMIT OF AZ31B MAGNESIUM ALLOY SHEET IN THE DEEP DRAWING WITH CROSS-SHAPED DIE

2008 ◽  
Vol 22 (31n32) ◽  
pp. 6045-6050 ◽  
Author(s):  
HEON YOUNG KIM ◽  
SUN CHUL CHOI ◽  
HYUNG JONG KIM ◽  
SEOK MOO HONG ◽  
YONG SEUNG SHIN ◽  
...  
Keyword(s):  
Finite Element ◽  
Magnesium Alloy ◽  
Deep Drawing ◽  
Temperature Deformation ◽  
Dome Height ◽  
Forming Limit ◽  
Process Conditions ◽  
Geometrical Parameters ◽  
Element Analysis ◽  
Az31b Magnesium Alloy

Magnesium alloy sheets are usually formed at temperatures between 150 and 300°C because of their poor formability at room temperature. In the present study, the formability of AZ31B magnesium alloy sheets was investigated by the analytical and experimental approaches. First, tensile tests and limit dome height tests were carried out at several temperatures between 25 and 300°C to get the mechanical properties and forming limit diagram (FLD). A FLD-based criterion considering the material temperature during deformation was used to predict the forming limit from a finite element analysis (FEA) of the cross-shaped cup deep drawing process. This criterion proved to be very useful in designing the geometrical parameters of the forming tools and determining optimal process conditions such as tool temperatures and blank shape by the comparison between finite element temperature-deformation analyses and physical try-out. The heating and cooling channels were also optimally designed through heat transfer analyses.

Sign in / Sign up

Export Citation Format

Share Document