twin roll
Recently Published Documents


TOTAL DOCUMENTS

1306
(FIVE YEARS 207)

H-INDEX

40
(FIVE YEARS 5)

Author(s):  
Bowen Wei ◽  
Tao Jiang ◽  
Shiju Li ◽  
Youyun Zhang ◽  
Guangming Xu ◽  
...  

Abstract The effect of superheat melt treatment(SMT) on microstructure and properties of Al-Mg-Si alloy fabricated by twin roll casting(TRC) was analyzed using optical microscope, scanning electron microscopy, emission electron probe micro analyzer and transmission electron microscopy. SMT increased the subcooling degree of melt during TRC. The solidification microstructure with high dendrite density and small dendrite spacing was obtained. The second phase was evenly distributed between dendrites and the solute concentration gradient was decreased. Intergranular solute aggregation caused by Reynolds’ dilatancy in TRC slab was effectively suppressed. The homogeneous solute distribution of TRC slab with SMT can be realized by short-time homogenization heat treatment. The size of insoluble particles was greatly reduced. The complete decomposition of non-equilibrium eutectic phase increased the solute concentration in α-Al, which promoted the precipitation of precipitates during aging heat treatment. The tensile strength and yield strength of T6 slab were improved, while the uniform elongation are almost not decreased. The strength and uniform of slab in T4P state were both improved. The obtained results can help further shorten the production cycle of TRC slabs and improve mechanical properties.


2021 ◽  
Author(s):  
Xiaoming Qian ◽  
Yu Zhang ◽  
Zhaodong Wang ◽  
X.-Grant Chen ◽  
Yong Li ◽  
...  

Abstract Dispersoid-strengthened Al-Mg-Si-Mn aluminum alloys were produced by twin-roll casting (TRC) and conventional mold casting (MC). An extra-low temperature homogenization was performed at temperature of 430 °C for 6 h, which was followed by uniaxial hot compression tests. The results showed that the as-cast TRC samples had a lower eutectic fraction with a smaller size and a higher solid solution concentration compared to the as-cast MC samples. During the extra-low temperature homogenization, a large number of α-Al(Fe, Mn)Si dispersoids precipitated, and the dispersoids in the TRC sample had a greater number density than those in the MC sample. Precipitation-free zone (PFZ) formed near the eutectic regions, TRC sample had a lower PFZ fraction than that of MC sample. The TRC samples yielded higher flow stresses of hot deformation than MC sample owing to the stronger dispersoid strengthening effect. Severe edge cracking occurred in the deformed MC samples due to the high fraction of coarse AlFeMnSi intermetallic particles, no edge crack formed in the TRC samples owing to its lower fraction and fine intermetallics which improved the hot workability of TRC sample.


Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7771
Author(s):  
Barbora Křivská ◽  
Michaela Šlapáková ◽  
Jozef Veselý ◽  
Martin Kihoulou ◽  
Klaudia Fekete ◽  
...  

Aluminium steel clad materials have high potential for industrial applications. Their mechanical properties are governed by an intermetallic layer, which forms upon heat treatment at the Al-Fe interface. Transmission electron microscopy was employed to identify the phases present at the interface by selective area electron diffraction and energy dispersive spectroscopy. Three phases were identified: orthorhombic Al5Fe2, monoclinic Al13Fe4 and cubic Al19Fe4MnSi2. An effective interdiffusion coefficient dependent on concentration was determined according to the Boltzmann–Matano method. The highest value of the interdiffusion coefficient was reached at the composition of the intermetallic phases. Afterwards, the process of diffusion considering the evaluated interdiffusion coefficient was simulated using the finite element method. Results of the simulations revealed that growth of the intermetallic phases proceeds preferentially in the direction of aluminium.


2021 ◽  
Vol 59 (12) ◽  
pp. 870-879
Author(s):  
Kyoung-Wook Kim ◽  
Min-Seok Baek ◽  
Kwangjun Euh ◽  
Kee-Ahn Lee

Al 7075 alloy was manufactured using the twin-roll strip casting (TRC) process, and the mechanical and wear properties of the fabricated TRC process were investigated. To compare the properties of the alloy manufactured by TRC, another Al 7075 alloy was fabricated by conventional direct chill (DC) casting as a comparative material. Based on initial microstructure observations, the Al 7075 alloy manufactured by the DC process showed relatively elongated grains compared to the Al 7075 alloy by TRC process. In both alloys, η(MgZn2) phases were present at the grain and grain boundaries. In the Al 7075 alloy manufactured by the DC process, the η(MgZn2) phases were coarse with a size of ~86 nm and were mainly concentrated in the local area. However, the Al 7075 alloy manufactured by TRC had relatively fine η(MgZn2) phases size of ~40 nm, and they were evenly distributed throughout the matrix. When the mechanical properties of the two alloys were compared, the TRC process showed higher hardness and strength properties than the DC process. In room temperature wear test results, the TRC process exhibited lower weight loss and wear rates compared to the DC process at all wear loads. In other words, the TRC process resulted in relatively superior wear resistance properties compared to the conventional DC process. The wear behavior of both alloys changed from abrasive wear to adhesive wear as the wear load increased. However, the TRC process maintained abrasive wear up to higher loads. Based on the above results, a correlation between the microstructure and wear mechanism of the Al 7075 alloy manufactured by TRC is also suggested.


Sign in / Sign up

Export Citation Format

Share Document