The effects of friction stir welding on the mechanical properties and microstructure of 7000 series aluminium tailor-welded blanks

2008 ◽  
Vol 1 (S1) ◽  
pp. 1311-1314 ◽  
Author(s):  
A. A. Zadpoor ◽  
J. Sinke ◽  
R. Benedictus
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Friction Stir ◽  
Tailor Welded Blanks

scholarly journals Effect of Stirring Pin Rotation Speed on Microstructure and Mechanical Properties of 2A14-T4 Alloy T-Joints Produced by Stationary Shoulder Friction Stir Welding

Materials ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 1938
Author(s):  
Haifeng Yang ◽  
Hongyun Zhao ◽  
Xinxin Xu ◽  
Li Zhou ◽  
Huihui Zhao ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Rotation Speed ◽  
Weld Nugget ◽  
Al Alloy ◽  
Nugget Zone ◽  
T Joints ◽  
Friction Stir ◽  
Stationary Shoulder ◽  
Microstructure And Mechanical Properties

In this study, 2A14-T4 Al-alloy T-joints were prepared via stationary shoulder friction stir welding (SSFSW) technology where the stirring pin’s rotation speed was set as different values. In combination with the numerical simulation results, the macro-forming, microstructure, and mechanical properties of the joints under different welding conditions were analyzed. The results show that the thermal cycle curves in the SSFSW process are featured by a steep climb and slow decreasing variation trends. As the stirring pin’s rotation speed increased, the grooves on the weld surface became more obvious. The base and rib plates exhibit W- or N-shaped hardness distribution patterns. The hardness of the weld nugget zone (WNZ) was high but was lower than that of the base material. The second weld’s annealing effect contributed to the precipitation and coarsening of the precipitated phase in the first weld nugget zone (WNZ1). The hardness of the heat affect zone (HAZ) in the vicinity of the thermo-mechanically affected zone (TMAZ) dropped to the minimum. As the stirring pin's rotation speed increased, the tensile strengths of the base and rib plates first increased and then dropped. The base and rib plates exhibited ductile and brittle/ductile fracture patterns, respectively.

Microstructure and Mechanical Properties at the Unsteady Areas of Non-Linear Friction Stir Welding

2007 ◽  
Vol 561-565 ◽  
pp. 1059-1062 ◽  
Author(s):  
H. Takahara ◽  
Masato Tsujikawa ◽  
Sung Wook Chung ◽  
Y. Okawa ◽  
Kenji Higashi
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Welding Parameter ◽  
Butt Joints ◽  
Friction Stir ◽  
Non Linear ◽  
Linear Friction ◽  
Fsw Parameters ◽  
Five Axis ◽  
Welding Direction

The influence of tool control in non-linear friction stir welding (FSW) on mechanical properties of joints was investigated. FSW is widely applied to linear joints. It is impossible for five axis FSW machines, however, to keep all the FSW parameters in optimum conditions at non-linear welding. Non-linear FSW joints should be made by compromise with the order of priority for FSW parameters. The tensile test results of butt joints with rectangular change in welding direction on plate plane (L-shaped butt joints) with various welding parameter change. It was found that turn to the retreating side is encouraged when welding direction change. And the method of zero inclination tool angle is effective at non-linear and plane welding.

scholarly journals The Effect of Vibration during Friction Stir Welding on Corrosion Behavior, Mechanical Properties, and Machining Characteristics of Stir Zone

Metals ◽  
2017 ◽  
Vol 7 (10) ◽  
pp. 421 ◽  
Author(s):  
Sajad Fouladi ◽  
Amir Ghasemi ◽  
Mahmoud Abbasi ◽  
Morteza Abedini ◽  
Amir Khorasani ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Friction Stir Welding ◽  
Corrosion Behavior ◽  
Stir Zone ◽  
Friction Stir ◽  
Machining Characteristics
Sign in / Sign up

Export Citation Format

Share Document