Kinematic analysis based on changes in arm support length and central axis location through rotational motion of the upper limb

Author(s):  
Jong Hyun Kim ◽  
Jae Soo Hong ◽  
Keyoung Jin Chun
Author(s):  
Jae Soo Hong ◽  
Keyoung Jin Chun ◽  
Jong Hyun Kim ◽  
Jung Hwa Hong

An increase in the aging population around the world and in degenerative diseases has caused an epidemic of stroke. Hence, rehab equipment for treating its after-effects has been actively developed. A repeated upper-body rehab exercise is required and this exercise can only yield good results when its accurate motion is guided by a therapist. However, few kinematics studies have been conducted based on design variables such as changes in the rotational central axis and body measurement. So, this study analyzed the angular changes in two motions of the elbow (Flexion-Extension: F-E, Pronation-Supination: P-S) and three motions of the scapula (Anterior-Posterior tilt: A-P, Internal-External rotation: I-E, Upward-Downward rotation: U-D) based on changes in the arm support length and central axis location. Eight healthy subjects participated in this study. Rehabilitation equipment for the upper limb, which can be adjusted to different arm support lengths and central axis locations, was used as the experimental equipment. The length could be adjusted to five levels (280 mm, 220 mm, 160 mm, 100 mm, and 40 mm). In the case of an experiment involving changes in the axis locations, the length was fixed as 280 mm, which allowed five different axis locations. Each subject implemented a rotational movement passively at an angular velocity of 30°/s. In this study, we observed changes in the motion patterns of the upper-limb rotational movement based on the length and the location. The patterns based on the two design variables revealed a consistent tendency under the elbow (forearm) and the scapula (shoulder rhythm). Yet, three scapula motions showed little changes in the angular width, and only I-E showed an angular width of 5°. First, with respect to the tendency of the five motions based on changes in the lengths, the prolonged length showed a decreased angular width. Second, in terms of the tendency of the five motions based on changes in the locations, a relatively long distance between the handle and the axis (Location 1 → Location 5) confirmed a decreased angular width owing to a relatively small rotational movement at Location 5. The F-E motion of the elbow clearly showed two time cycles per rotation. Other motions revealed one time cycle per rotation. With respect to the upper-body rotational movement, we confirmed that motions related to the forearm were more active than motions related to the shoulder.


2017 ◽  
Vol 32 (11) ◽  
pp. 936-941 ◽  
Author(s):  
Roser Pons ◽  
Athanasios Vanezis ◽  
Helen Skouteli ◽  
Antigoni Papavasiliou ◽  
Magda Tziomaki ◽  
...  

2006 ◽  
Vol 15 (4) ◽  
pp. 247-256 ◽  
Author(s):  
Frank Fitoussi ◽  
Amadou Diop ◽  
Nathalie Maurel ◽  
El Mostafa Laassel ◽  
Georges François Penneçot

Author(s):  
R. Michnik ◽  
J. Jurkojć ◽  
Z. Rak ◽  
A. Mężyk ◽  
Z. Paszenda ◽  
...  

2015 ◽  
Vol 8 (2) ◽  
Author(s):  
Basilio Lenzo ◽  
Marco Fontana ◽  
Simone Marcheschi ◽  
Fabio Salsedo ◽  
Antonio Frisoli ◽  
...  

This article introduces the design and the experimental validation of the Trackhold, a novel mechanical motion-tracker for upper limb physical rehabilitation. The Trackhold is based on a passively balanced mechanism that can approximately relieve the weight of the patient’s arm regardless of the position. The system features a novel kinematic architecture with large workspace and custom developed joint sensors providing accurate real-time measure of the upper limb posture. The design approach of the device, which went through kinetostatic and dynamic analyses, is presented and details on the employed mechatronic solutions are provided. A prototype of the Trackhold has been fabricated and functionally validated.


2010 ◽  
Vol 97-101 ◽  
pp. 2785-2791
Author(s):  
Ai Ping Li ◽  
Jun Hu ◽  
Jian Guo Zhang

This paper simplifies the upper limb lifting mechanism of the multifunctional wheelchair, takes the dynamic simulation tool Simulink of MATLAB as a platform, establishes a simulation model for kinematic analysis on the upper limb lifting mechanism, and executes the simulation after all parameters are set. The result shows that such simulation can help to conveniently and accurately get the motion parameters of the mechanism and optimize the parameters immediately, so that reference can be provided for type selection of this mechanism, it can be better understand the working condition of the multifunctional wheelchair, and complete the structure of product prototypes.


Sign in / Sign up

Export Citation Format

Share Document