Stability criterion for stick-slip motion using a discontinuous dynamic friction model

Wear ◽  
1976 ◽  
Vol 40 (1) ◽  
pp. 113-120 ◽  
Author(s):  
G. Cockerham ◽  
G.R. Symmons
1994 ◽  
Vol 47 (7) ◽  
pp. 255-274 ◽  
Author(s):  
W. W. Tworzydlo ◽  
E. B. Becker ◽  
J. T. Oden

A numerical study of dynamic instabilities and vibrations of mechanical systems with friction is presented. Of particular interest are friction-induced vibrations, self-excited oscillations and stick-slip motion. A typical pin-on-disk apparatus is modeled as the assembly of rigid bodies with elastic connections. An extended version of the Oden-Martins friction model is used to represent properties of the interface. The mechanical model of the frictional system is the basis for numerical analysis of dynamic instabilities caused by friction and of self-excited oscillations. Coupling between rotational and normal modes is the primary mechanism of resulting self-excited oscillations. These oscillations combine with high-frequency stick-slip motion to produce a significant reduction of the apparent kinetic coefficient of friction. As a particular study model, a pin-on-disk experimental setup has been selected. A good qualitative and quantitative correlation of numerical and experimental results is observed.


1994 ◽  
Vol 64 (4) ◽  
pp. 224-229 ◽  
Author(s):  
S.A. Hosseini Ravandi ◽  
K. Toriumi ◽  
Y. Matsumoto

Author(s):  
A. A. Abouelsoud ◽  
J. Abdo Ahmed

Friction-induced self-sustained oscillation result in a very robust limit cycle that characterizes stick-slip motion. This motion should be avoided because it creates unwanted noise, diminishes accuracy, and increases wear. The stick-slip motion produced by a mass-spring-damper on a moving belt is analyzed using Lyapunov second method, which is based on constructing a positive definite function and checking the condition for which its time derivative is negative semi-definite. From this condition an estimate of the amplitude of the velocity of the limit cycle of the stick-slip motion is obtained. This estimate is found to be the zero of a certain function derived from the Coulomb friction model. An estimate of the amplitude of the displacement is also found. It is shown that the simulation results of the amplitude and the estimated amplitude are in a good match.


2008 ◽  
Vol 33-37 ◽  
pp. 867-874 ◽  
Author(s):  
S. Ozaki ◽  
Koichi Hashiguchi ◽  
D.H. Chen

In this study, the rate-dependent subloading-friction model, which can rationally describe the reciprocal transition of static-kinetic frictions by the unified formulation, is proposed. Then, the one-dimensional model of spring-mass system is implemented by incorporating the present friction model, and is applied to simulations of stick-slip motion. Further, we verified the validity of the present approach for the stick-slip motion by numerical experiments under various dynamic conditions.


2015 ◽  
Vol 6 (1) ◽  
pp. 15-28 ◽  
Author(s):  
Y. F. Liu ◽  
J. Li ◽  
Z. M. Zhang ◽  
X. H. Hu ◽  
W. J. Zhang

Abstract. The micro stick-slip motion systems, such as piezoelectric stick-slip actuators (PE-SSAs), can provide high resolution motions yet with a long motion range. In these systems, friction force plays an active role. Although numerous friction models have been developed for the control of micro motion systems, behaviors of these models in micro stick-slip motion systems are not well understood. This study (1) gives a survey of the basic friction models and (2) tests and compares 5 friction models in the literature, including Coulomb friction model, Stribeck friction model, Dahl model, LuGre model, and the elastoplastic friction model on the same test-bed (i.e. the PE-SSA system). The experiments and simulations were done and the reasons for the difference in the performance of these models were investigated. The study concluded that for the micro stick-slip motion system, (1) Stribeck model, Dahl model and LuGre model all work, but LuGre model has the best accuracy and (2) Coulomb friction model and the elastoplastic model does not work. The study provides contributions to motion control systems with friction, especially for micro stick-slip or step motion systems as well as general micro-motion systems.


2011 ◽  
Vol 305 (3-4) ◽  
pp. 283-289 ◽  
Author(s):  
J. Paul Winberry ◽  
Sridhar Anandakrishnan ◽  
Douglas A. Wiens ◽  
Richard B. Alley ◽  
Knut Christianson

2008 ◽  
Vol 16 (6) ◽  
pp. 724-735 ◽  
Author(s):  
Yasushi Kojima ◽  
Shigemune Taniwaki ◽  
Yoshiaki Okami

Sign in / Sign up

Export Citation Format

Share Document