The prediction of the three-dimensional turbulent flow field in a flow-splitting tee-junction

1978 ◽  
Vol 13 (3) ◽  
pp. 293-306 ◽  
Author(s):  
A. Pollard ◽  
D.B. Spalding
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Flow Splitting ◽  
Tee Junction ◽  
Turbulent Flow Field

Numerical simulations and analysis of the turbulent flow field in a practical gas turbine engine combustor

2021 ◽  
pp. 095765092110632
Author(s):  
Veeraraghava R Hasti ◽  
Prithwish Kundu ◽  
Sibendu Som ◽  
Jay P Gore
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Numerical Simulations ◽  
Gas Turbine ◽  
Adaptive Mesh Refinement ◽  
Three Dimensional ◽  
Adaptive Mesh ◽  
Turbulent Structures ◽  
Cut Cell ◽  
Turbulent Flow Field

The turbulent flow field in a practical gas turbine combustor is very complex because of the interactions between various flows resulting from components like multiple types of swirlers, dilution holes, and liner effusion cooling holes. Numerical simulations of flows in such complex combustor configurations are challenging. The challenges result from (a) the complexities of the interfaces between multiple three-dimensional shear layers, (b) the need for proper treatment of a large number of tiny effusion holes with multiple angles, and (c) the requirements for fast turnaround times in support of engineering design optimization. Both the Reynolds averaged Navier–Stokes simulation (RANS) and the large eddy simulation (LES) for the practical combustor geometry are considered. An autonomous meshing using the cut-cell Cartesian method and adaptive mesh refinement (AMR) is demonstrated for the first time to simulate the flow in a practical combustor geometry. The numerical studies include a set of computations of flows under a prescribed pressure drop across the passage of interest and another set of computations with all passages open with a specified total flow rate at the plenum inlet and the pressure at the exit. For both sets, the results of the RANS and the LES flow computations agree with each other and with the corresponding measurements. The results from the high-resolution LES simulations are utilized to gain fundamental insights into the complex turbulent flow field by examining the profiles of the velocity, the vorticity, and the turbulent kinetic energy. The dynamics of the turbulent structures are well captured in the results of the LES simulations.

Turbulence Measurements in the Corner Wall Jet

2014 ◽  
Author(s):  
Barrett Poole ◽  
Joseph W. Hall
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Wall Jet ◽  
Hot Wire ◽  
Turbulence Measurements ◽  
Vertical Growth ◽  
The Mean ◽  
Turbulent Flow Field

The corner wall jet is similar to the standard three-dimensional wall jet with the exception that one half of the surface has been rotated counter-clockwise by 90 degrees. The corner wall jet investigated here is formed using a long round pipe with a Reynolds number of 159,000. Contours of the mean and turbulent flow field were measured using hot-wire anemometry. The results indicate that the ratio of lateral to vertical growth in the corner wall jet is approximately half of that in a standard turbulent three-dimensional wall jet.

Turbulent flow field in a scour hole at a semicircular abutment

2005 ◽  
Vol 32 (1) ◽  
pp. 213-232 ◽  
Author(s):  
Subhasish Dey ◽  
Abdul Karim Barbhuiya
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Shear Stresses ◽  
Reynolds Stresses ◽  
Primary Vortex ◽  
Scour Hole ◽  
Turbulent Flow Field ◽  
Development And Validation ◽  
Bed Shear Stresses

The three-dimensional turbulent flow field in a scour hole at a semicircular abutment under a clear water regime was experimentally measured in a laboratory flume using an acoustic Doppler velocimeter. The distributions of time-averaged velocity components, turbulent intensity components, turbulent kinetic energy, and Reynolds stresses at different azimuthal planes are presented. Upstream, presentation of flow field through vector plots at azimuthal and horizontal planes shows the existence of a large primary vortex associated with the downflow inside the scour hole. On the other hand, downstream, the flow field is irregular. The bed shear stresses are determined from the Reynolds stresses and velocity gradients. The data presented in this paper would be useful for the development and validation of flow field models, which can be used to determine the strength of the primary vortex that is used to estimate scour depth at bridge abutments.Key words: bridge abutments, fluid flow, three-dimensional flow, turbulent flow, open channel flow, scour, sediment transport, hydraulic engineering.

A Numerical Investigation of the Turbulent Flow Field Generated by a Stationary Cube

1991 ◽  
Vol 113 (2) ◽  
pp. 216-222 ◽  
Author(s):  
R. Raul ◽  
P. S. Bernard
Keyword(s):  
Flow Field ◽  
Turbulent Flow ◽  
Bluff Body ◽  
Equations Of Motion ◽  
Three Dimensional ◽  
Dynamical Equations ◽  
Kinematic Equation ◽  
Wall Functions ◽  
Turbulent Flow Field ◽  
Vorticity Transport

The turbulent flow field generated by a stationary cube at Reynolds numbers 2000 and 14,000 is investigated numerically. A vorticity-vector potential formulation of the equations of motion is employed. Turbulence effects are accounted for through the use of a vorticity transport closure scheme in which dynamical equations for vorticity mean and covariance are supplemented by a kinematic equation for turbulent kinetic energy. Semi-implicit finite difference approximations to the equations of motion are solved iteratively by a vectorizable 8-color SOR algorithm. The numerical mesh is designed so that the turbulent flow field can be computed down to solid surfaces without the use of wall functions. The properties of the computed flow field, including drag, axial velocity, separation points, and three-dimensional flow structure show good agreement with experimental observations of similar bluff body flows.

Turbulence Measurements in a Corner Wall Jet1

2016 ◽  
Vol 138 (8) ◽  
Author(s):  
Barrett Poole ◽  
Joseph W. Hall
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Turbulent Flow ◽  
Three Dimensional ◽  
Numerical Code ◽  
Wall Jet ◽  
Hot Wire ◽  
Practical Applications ◽  
The Mean ◽  
Turbulent Flow Field

The corner wall jet is similar to the standard three-dimensional wall jet with the exception that one-half of the surface has been rotated counterclockwise by 90 deg. The corner wall jet is selected for study as the geometry occurs in practical applications and is an ideal benchmark case for numerical code validation. The corner wall jet investigated here is formed using a long round pipe with a Reynolds number of 159,000. Contours of the mean and turbulent flow field were measured using hot-wire anemometry from x/D = 0 to 40. The results indicate that the ratio of lateral-to-vertical growth in the corner wall jet is approximately half that in a standard turbulent three-dimensional wall jet. The results indicate that this behavior is not simply tied to a slower development of the corner wall jet.

Sign in / Sign up

Export Citation Format

Share Document