Free fall water entry of a cone in three degrees of freedom

2020 ◽  
Vol 101 ◽  
pp. 102273 ◽  
Author(s):  
Shi-Li Sun ◽  
Yong Cheng ◽  
Jie Cui ◽  
Shi-Yan Sun
Keyword(s):  
Degrees Of Freedom ◽  
Free Fall ◽  
Water Entry ◽  
Three Degrees Of Freedom

Simulation of water entry of a wedge through free fall in three degrees of freedom

2010 ◽  
Vol 466 (2120) ◽  
pp. 2219-2239 ◽  
Author(s):  
G. D. Xu ◽  
W. Y. Duan ◽  
G. X. Wu
Keyword(s):  
Degrees Of Freedom ◽  
Velocity Potential ◽  
Free Fall ◽  
Water Entry ◽  
Auxiliary Function ◽  
The Body ◽  
Body Motion ◽  
Time Stepping ◽  
The Impact ◽  
Three Degrees Of Freedom

The water entry problem of a wedge through free fall in three degrees of freedom is studied through the velocity potential theory for the incompressible liquid. In particular, the effect of the body rotation is taken into account, which seems to have been neglected so far. The problem is solved in a stretched coordinate system through a boundary element method for the complex potential. The impact process is simulated based on the time stepping method. Auxiliary function method has been used to decouple the mutual dependence between the body motion and the fluid flow. The developed method is verified through results from other simulation and experimental data for some simplified cases. The method is then used to undertake extensive investigation for the free fall problems in three degrees of freedom.

Effect of Wind Loads on the Performance of Free-Fall Lifeboats

2014 ◽  
Author(s):  
Thomas Sauder ◽  
Eloise Croonenborghs ◽  
Sebastien Fouques ◽  
Nabila Berchiche ◽  
Svein-Arne Reinholdtsen
Keyword(s):  
Numerical Simulations ◽  
Degrees Of Freedom ◽  
Free Fall ◽  
Offshore Structures ◽  
Water Entry ◽  
Forward Speed ◽  
Cfd Simulations ◽  
Six Degrees Of Freedom ◽  
Complete Set ◽  
Water Exit

The paper presents a model describing the launch of free-fall lifeboats from offshore structures in strong environmental wind. Six-degrees-of-freedom numerical simulations of the lifeboat launch are performed using the free-fall lifeboat simulator VARUNA with a complete set of wind coefficients for the lifeboat. Those wind coefficients are obtained by CFD simulations validated against wind tunnel tests. The lifeboat launch simulations are then verified against time-domain CFD simulations of the whole launch in air until water entry. It is shown by means of numerical simulations that wind-induced loads on the lifeboat have a strong influence on its kinematics until water entry, and subsequently on the acceleration loads experienced by the occupants, on the structural loads on the lifeboat, and on its forward speed after water exit. It is concluded that the effect of wind-induced loads on the lifeboat performances should in general be investigated when establishing the operational limits for a given offshore installation.

scholarly journals Two-Dimensional Impact Modelling with Three Degrees of Freedom and Its Application in the Dynamics of Planing Hulls

2020 ◽  
Vol 10 (3) ◽  
pp. 1072
Author(s):  
Roberto Algarín ◽  
Antonio Bula
Keyword(s):  
Degrees Of Freedom ◽  
Numerical Solutions ◽  
Cross Flow ◽  
Free Fall ◽  
Three Dimensions ◽  
Two Dimensional ◽  
Slender Body Theory ◽  
Impact Modelling ◽  
The Impact ◽  
Three Degrees Of Freedom

Planing boat dynamics are a complex phenomenon and the maneuver forces acting on these kind of hulls are difficult to predict. In the current work, a mathematical model of a two-dimensional impact with three degrees of freedom (3DOF) is developed. The model was used to study wedge sections with knuckles, the vertical, horizontal, and rotational motion are considered. Pressure distribution, forces, and motion during the impact, considering both free fall and forced motion, are evaluated. The commercial CFD (Computational flow dynamics) software Star-CCM+ V9.06 was used to validate the formulation. Simulations with one, two, and three degrees of freedom were carried out, and the results were compared with CFD simulations, experimental data, and numerical solutions by others authors. The results show a good agreement with the authors. The model is extended to three dimensions applying slender body theory, and the forces in the hull are computed. The formulation allows evaluating the seakeeping with cross flow, dynamic stability, and manoeuvrability of planing boats with variable sections over the length.

scholarly journals Active Disturbance Rejection for a Three Degrees of Freedom Gyroscope

2018 ◽  
Vol 51 (13) ◽  
pp. 372-377 ◽  
Author(s):  
Juan E. Andrade García ◽  
Alejandra Ferreira de Loza ◽  
Luis T. Aguilar ◽  
Ramón I. Verdés
Keyword(s):  
Disturbance Rejection ◽  
Degrees Of Freedom ◽  
Active Disturbance Rejection ◽  
Three Degrees Of Freedom

scholarly journals Cyclic Deformation of Microcantilevers Using In-Situ Micromanipulation

2021 ◽  
Author(s):  
A. H. S. Iyer ◽  
M. H. Colliander
Keyword(s):  
Degrees Of Freedom ◽  
Focused Ion Beam ◽  
Ion Beam ◽  
Structural Components ◽  
Cyclic Testing ◽  
Phase Boundaries ◽  
Bulk Specimen ◽  
Arbitrary Position ◽  
Three Degrees Of Freedom

Abstract Background The trend in miniaturisation of structural components and continuous development of more advanced crystal plasticity models point towards the need for understanding cyclic properties of engineering materials at the microscale. Though the technology of focused ion beam milling enables the preparation of micron-sized samples for mechanical testing using nanoindenters, much of the focus has been on monotonic testing since the limited 1D motion of nanoindenters imposes restrictions on both sample preparation and cyclic testing. Objective/Methods In this work, we present an approach for cyclic microcantilever bending using a micromanipulator setup having three degrees of freedom, thereby offering more flexibility. Results The method has been demonstrated and validated by cyclic bending of Alloy 718plus microcantilevers prepared on a bulk specimen. The experiments reveal that this method is reliable and produces results that are comparable to a nanoindenter setup. Conclusions Due to the flexibility of the method, it offers straightforward testing of cantilevers manufactured at arbitrary position on bulk samples with fully reversed plastic deformation. Specific microstructural features, e.g., selected orientations, grain boundaries, phase boundaries etc., can therefore be easily targeted.

Sign in / Sign up

Export Citation Format

Share Document