An experimental investigation of heat transfer performance in a polydimethylsiloxane (PDMS) oscillating heat pipe

2013 ◽  
Vol 61 (2) ◽  
pp. 690-697 ◽  
Author(s):  
Yulong Ji ◽  
Gongwei Liu ◽  
Hongbin Ma ◽  
Gen Li ◽  
Yuqing Sun
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

An Experimental Investigation of the Heat Transfer Performance of an Oscillating Heat Pipe With Copper Oxide (CuO) Microstructure Layer on the Inner Surface

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Yulong Ji ◽  
Chen Xu ◽  
Hongbin Ma ◽  
Pan Xinxiang
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Copper Oxide ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Inner Surface ◽  
Copper Tubing

This paper presents an experimental investigation of whether heat transfer performance in an oscillating heat pipe (OHP) would improve if the inner surface of the heat pipe was coated with a layer of copper oxide (CuO). The OHP had six turns and three sections, i.e., evaporator, condenser, and adiabatic section with lengths of 40 mm, 64 mm, and 51 mm, respectively. The cleaned copper tubing was chemically treated with a chemical solution and heated in a furnace. A microstructure layer of CuO was formed in the inner surface of the OHP with K2S2O8 and KOH. The working fluid in this study was water with filling ratios ranging from 40% to 70%. The experimental results show that the CuO microstructure layer is superhydrophilic and can enhance the OHP heat transfer performance. The investigation results in a new way to enhance the heat transfer performance of an OHP.

Experimental Investigation of Ultrasonic Effect on an Acetone Oscillating Heat Pipe

2013 ◽  
Author(s):  
Nannan Zhao ◽  
Benwei Fu ◽  
Dianli Zhao ◽  
Hongbin Ma
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Power Input ◽  
Input Power ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Ultrasonic Effect ◽  
Ultrasonic Sound ◽  
Oscillating Motion

The ultrasonic effect on the oscillating motion and heat transfer in an oscillating heat pipe (OHP) containing acetone was investigated experimentally. The ultrasonic sound was applied to the evaporating section of the OHP by using electrically-controlled piezoelectric ceramics. The ultrasonic sound is used to generate and maintain the oscillating motion, and, thereby, heat transfer is enhanced. The heat pipe was tested with or without the ultrasonic sound. In addition, the effects of heat load, filling ratio, orientation, operating temperature, and input power from 15 W to 200 W were investigated. The experimental results demonstrate that ultrasonic sound can affect the oscillating motions and enhance the heat transfer performance of the acetone OHP. In particular, the application of the ultrasonic sound on an acetone OHP can significantly reduce the thermal resistance of the acetone OHP and enhance the heat transfer performance in a low power input region. The investigation will provide an insight into the oscillating mechanism of the acetone OHP influenced by ultrasonic sound and provide a new way to enhance the heat transfer performance of the OHP.

Experimental Study on Oscillating Heat Pipe With Hydraulic Diameter Far Exceeding the Maximum Hydraulic Diameter

2019 ◽  
Author(s):  
Lilin Chu ◽  
Yulong Ji ◽  
Chunrong Yu ◽  
Yantao Li ◽  
Hongbin Ma ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Transfer Performance ◽  
Vertical Orientation ◽  
Oscillating Heat Pipe ◽  
Horizontal Orientation ◽  
Small Bubbles

Abstract In order to understand the heat transfer performance, startup and fluid flow condition of oscillating heat pipe (OHP) with hydraulic diameter far exceeding the maximum hydraulic diameter (MHD), an experimental investigation on heat transfer performance and visualization was conducted. From the experimental performance, it is found that the OHP can still work well with ethanol as the working fluid when the tube diameter has exceeded the MHD of 91.6%. In addition, the detailed flow patterns of the OHP were recorded by a highspeed camera for vertical and horizontal orientation to understand its physical mechanism. In the vertical orientation, initially working fluid generates small bubbles, and then the small bubbles coalesce and grow to vapor plugs, the vapor plugs finally pushes the liquid slugs to oscillate in the tube. In the horizontal orientation, the working fluid surface fluctuates due to the vapors flow from the evaporator to the condenser and bubbles burst in the evaporator. When the peak of liquid wave reaches the upper surface of tube, a liquid slug has been formed, and then the steam flow pushes the liquid slugs to oscillate in the tube.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

Sign in / Sign up

Export Citation Format

Share Document