scholarly journals Particle-resolved simulations of shock-induced inviscid flow through particle-curtain at initial stage

2021 ◽  
pp. 105196
Author(s):  
Ling-Jie Jiang ◽  
Maojun Li
2002 ◽  
Vol 124 (4) ◽  
pp. 977-987 ◽  
Author(s):  
Bogdan I. Epureanu ◽  
Earl H. Dowell ◽  
Kenneth C. Hall

An unsteady inviscid flow through a cascade of oscillating airfoils is investigated. An inviscid nonlinear subsonic and transonic model is used to compute the steady flow solution. Then a small amplitude motion of the airfoils about their steady flow configuration is considered. The unsteady flow is linearized about the nonlinear steady response based on the observation that in many practical cases the unsteadiness in the flow has a substantially smaller magnitude than the steady component. Several reduced-order modal models are constructed in the frequency domain using the proper orthogonal decomposition technique. The dependency of the required number of aerodynamic modes in a reduced-order model on the far-field upstream Mach number is investigated. It is shown that the transonic reduced-order models require a larger number of modes than the subsonic models for a similar geometry, range of reduced frequencies and interblade phase angles. The increased number of modes may be due to the increased Mach number per se, or the presence of the strong spatial gradients in the region of the shock. These two possible causes are investigated. Also, the geometry of the cascade is shown to influence strongly the shape of the aerodynamic modes, but only weakly the required dimension of the reduced-order models.


2000 ◽  
Vol 10 (2) ◽  
pp. 62-72 ◽  
Author(s):  
S. V. Kotomin ◽  
S. V. Antonov ◽  
V. E. Dreval ◽  
M. L. Kerber ◽  
V. G. Kulichikhin

Abstract Impregnation and infiltration of fibrous materials by LC copolyester melts and the blends with viscous thermo-plastic polysulphone were quantitatively described as unsteady and steady stages in terms of rheological characteristics of the melts using an equivalent capillary model. Addition of LC polyester to viscous thermoplastic melt noticeably enhances impregnation condition. Study of the melt flow through various capillaries demonstrated a development of the melt slippage at high shear rate along the capillary walls. Slippage phenomena may be important at the initial stage of impregnation but can be neglected for final stage due to low shear rate in the last case. On the other hand, at those conditions a yield stress of the melt may considerably complicate the impregnation process due to a drastic viscosity increase.


1972 ◽  
Vol 11 (4) ◽  
pp. 590-593 ◽  
Author(s):  
J. Larry Duda ◽  
James S. Vrentas

2015 ◽  
Vol 2015 ◽  
pp. 1-6 ◽  
Author(s):  
Zong-qi Lei ◽  
Guo-zhu Liang

An improved panel method has been developed to calculate compressible inviscid flow through a turbine blade row. The method is a combination of the panel method for infinite cascade, a deviation angle model, and a compressibility correction. The resulting solution provides a fast flexible mesh-free calculation for cascade flow. A VKI turbine blade cascade is used to evaluate the method, and the comparison with experiment data is presented.


AIAA Journal ◽  
1971 ◽  
Vol 9 (10) ◽  
pp. 2043-2050 ◽  
Author(s):  
B. SCHORR ◽  
K. C. REDDY
Keyword(s):  

1984 ◽  
Author(s):  
U. K. Singh

An inviscid-viscous interaction treatment has been developed to predict the flow through transonic axial turbine blade cascades. The treatment includes a trailing-edge base pressure model. This model is based on treating the area between the points of flow separation on the blade surfaces at the trailing-edge and the point of downstream confluence of the suction and pressure surface flows as a region of constant pressure. A time marching technique is used to calculate the inviscid flow and viscous flow is calculated by integral methods for laminar and turbulent boundary layers. Good agreement with experimental data has been obtained.


Sign in / Sign up

Export Citation Format

Share Document