Damage mechanisms in cementitious coatings on steel members under axial loading

2015 ◽  
Vol 90 ◽  
pp. 18-35 ◽  
Author(s):  
Suwen Chen ◽  
Liming Jiang ◽  
Asif Usmani ◽  
Guo-Qiang Li ◽  
Chu Jin
Keyword(s):  
Axial Loading ◽  
Damage Mechanisms ◽  
Steel Members

scholarly journals Damage mechanisms in cementitious coatings on steel members in bending

2015 ◽  
Vol 168 (5) ◽  
pp. 351-369 ◽  
Author(s):  
Suwen Chen ◽  
Liming Jiang ◽  
Asif Usmani ◽  
Guo-Qiang Li
Keyword(s):  
Damage Mechanisms ◽  
Steel Members

scholarly journals Behaviour of tubular steel members under cyclic axial loading

2006 ◽  
Vol 62 (1-2) ◽  
pp. 121-131 ◽  
Author(s):  
J.M. Goggins ◽  
B.M. Broderick ◽  
A.Y. Elghazouli ◽  
A.S. Lucas
Keyword(s):  
Axial Loading ◽  
Steel Members

scholarly journals Numerical Modeling of Square Steel Members Wrapped by CFRP Composites

2019 ◽  
Vol 8 (10) ◽  
pp. 3082-3087 ◽  
Keyword(s):  
Failure Modes ◽  
Ultimate Load ◽  
Local Buckling ◽  
Axial Loading ◽  
Test Results ◽  
Structural Members ◽  
Cfrp Sheets ◽  
Tubular Columns ◽  
Steel Members ◽  
Strain Behaviour

HSS (Hollow Structural Steel) tubular members used in buildings and bridges for structural application is rapidly developing technique in the recent era. Since, they have many advantages over RC structural members. This paper presents the application of CFRP on HSS tubular members under axial compression. Typical failure occurred during axial loading was local buckling, and this could be reduced by wrapping CFRP sheets around the HSS tubular columns were investigated experimentally. Eight steel samples are used in this test. Among eight specimens, two are unwrapped and the remaining six columns are externally wrapped by CFRP. CFRP sheets are used as strips, and the width of the sheets are constant. The spacing between the CFRP sheets is also constant. All columns are tested in column tester till the maximum to understand their failure modes, Ultimate load, load Vs. Displacement, Stress- Strain behaviour and Ductility index. Finally, results obtained from the experimental investigation could be validated with ANSYS software. The ultimate load and displacements from ANSYS validation are closely match with test results.

Correlation of axial loaded magnetic resonance imaging with clinical symptoms in lumbar spinal canal stenosis patients

MedPharmRes ◽  
2019 ◽  
Vol 2 (4) ◽  
pp. 15-19
Author(s):  
Son Nguyen ◽  
Son Vi ◽  
Hoat Luu ◽  
Toan Do
Keyword(s):  
Spinal Canal ◽  
Clinical Symptoms ◽  
Axial Loading ◽  
Spinal Canal Stenosis ◽  
Leg Pain ◽  
Cross Sectional ◽  
Canal Stenosis ◽  
Conventional Mri ◽  
Frame System ◽  
Lumbar Spinal

There are cases when symptoms are available but no abnormal stenosis is found in MRI and vice versa. Axial-loaded MRI has been shown that it can demonstrate more accurately the real status of spinal canal stenosis than conventional MRI. This is the first time we applied a new system that we have recreated from the original loading frame system in order to fit with the demands of Vietnamese people. Sixty-two patients were selected from Phu Tho Hospital in Phu Tho Province, Vietnam, who fulfilled the inclusion criteria. The Anterior-posterior diameter (APD), Dura Cross-sectional Area (DSCA) in conventional MRI and axial loaded MRI, and changes in APD and DCSA were determined at the single most constricted intervertebral level. The APD and DCSA in axial loaded MRI had very good significant correlations with VAS for back pain (rs=0.83, 0.79), leg pain (rs=0.69, 0.57) and JOA score (rs=0.70, 0.65). APD and DCSA in axial loaded MRI significantly correlated with the severity of symptoms. Our axial loading MRI provides more valuable information than the conventional MRI for assessing patients with LSCS.

BÖHLER W405 ISOBLOC

Alloy Digest ◽  
2013 ◽  
Vol 62 (10) ◽  
Keyword(s):  
Thermal Conductivity ◽  
North America ◽  
Physical Properties ◽  
Heat Treating ◽  
Damage Mechanisms ◽  
Hot Work Steel

Abstract Böhler (or Boehler) W405 is a hot work steel with a great combination of hardness, strength, toughness, ductility, and thermal conductivity to resist typical damage mechanisms in applications. This datasheet provides information on composition, physical properties, and elasticity. It also includes information on forming and heat treating. Filing Code: TS-722. Producer or source: Böhler-Uddeholm North America.

Sign in / Sign up

Export Citation Format

Share Document