A discussion of “Numerical and experimental investigations on fretting fatigue: Relative slip, crack path, and fatigue life” by N. Noraphaiphipaksa, C. Kanchanomai, and Y. Mutoh

2015 ◽  
Vol 133 ◽  
pp. 52-55 ◽  
Author(s):  
D.A. Hills ◽  
R.C. Flicek
Keyword(s):  
Fatigue Life ◽  
Crack Path ◽  
Fretting Fatigue ◽  
Experimental Investigations ◽  
Relative Slip

scholarly journals Fretting Fatigue with Cylindrical-On-Flat Contact: Crack Nucleation, Crack Path and Fatigue Life

Materials ◽  
2017 ◽  
Vol 10 (2) ◽  
pp. 155 ◽  
Author(s):  
Nitikorn Noraphaiphipaksa ◽  
Anchalee Manonukul ◽  
Chaosuan Kanchanomai
Keyword(s):  
Fatigue Life ◽  
Crack Path ◽  
Crack Nucleation ◽  
Fretting Fatigue ◽  
Flat Contact

Influence of Wear Properties on Fretting Fatigue Life of a CK45 Alloy and the Al7175 Alloy

2008 ◽  
Vol 587-588 ◽  
pp. 971-975 ◽  
Author(s):  
M. Buciumeanu ◽  
A.S. Miranda ◽  
F.S. Silva
Keyword(s):  
Wear Resistance ◽  
Fatigue Life ◽  
Material Properties ◽  
Fatigue Behavior ◽  
Synergetic Effect ◽  
Fretting Fatigue ◽  
Reduction Factor ◽  
Strength Reduction ◽  
Strength Reduction Factor ◽  
Wear Properties

The main objective of this work was to study the influence of the wear properties of two commercial alloys (CK45 and Al7175) on their fretting fatigue behavior. It is verified the effect of material local degradation by wear on a fatigue strength reduction factor, namely the stress concentration factor, and on the overall fretting fatigue life of these materials. The fretting fatigue phenomenon is a synergetic effect between wear and fatigue. It is dependent on both the fatigue and the wear properties of the materials. Material properties promoting an increase in wear resistance should enhance fretting fatigue life.

Probabilistic fretting fatigue life prediction of Ti–6Al–4V

2010 ◽  
Vol 32 (12) ◽  
pp. 1937-1947 ◽  
Author(s):  
Patrick J. Golden ◽  
Harry R. Millwater ◽  
Xiaobin Yang
Keyword(s):  
Fatigue Life ◽  
Life Prediction ◽  
Fretting Fatigue ◽  
Fatigue Life Prediction

The Effects of Periodic High Loads on Fretting Fatigue

1981 ◽  
Vol 103 (3) ◽  
pp. 223-228 ◽  
Author(s):  
A. Kantimathi ◽  
J. A. Alic
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Growth Retardation ◽  
Fretting Fatigue ◽  
Fatigue Tests ◽  
Constant Amplitude ◽  
Axial Loads ◽  
Prolonged Fatigue ◽  
Stress Ratios ◽  
Crack Growth Retardation

Fretting fatigue tests have been conducted on 7075-T7351 aluminum alloy coupons with fretting pads of the same material. Three different stress ratios were used, the otherwise constant amplitude axial loads being interrupted every 1000 cycles by either tensile overloads to 400 MPa or compressive underloads to −200 MPa. Tensile overloads greatly prolonged fatigue life for low stresses where the overload ratios were 1.6 and above; compressive underloads had comparatively little effect. The results are discussed in terms of crack growth retardation phenomena.

Observations and Analysis of Relative Slip in Fretting Fatigue

2008 ◽  
pp. 33-33-11 ◽  
Author(s):  
T Nishida ◽  
K Kondoh ◽  
J-Q Xu ◽  
Y Mutoh
Keyword(s):  
Fretting Fatigue ◽  
Relative Slip

Numerical Analysis of the Effect of Contact Pressure on the Fretting Fatigue Life in a Press-Fitted Shaft

2009 ◽  
Vol 54 (3) ◽  
pp. 1115-1118 ◽  
Author(s):  
Dong-Hyong Lee ◽  
Seok-Jin Kwon ◽  
Won-Hee You ◽  
Jae-Boong Choi ◽  
Young-Jin Kim
Keyword(s):  
Fatigue Life ◽  
Numerical Analysis ◽  
Contact Pressure ◽  
Fretting Fatigue
Sign in / Sign up

Export Citation Format

Share Document