The Effects of Periodic High Loads on Fretting Fatigue

1981 ◽  
Vol 103 (3) ◽  
pp. 223-228 ◽  
Author(s):  
A. Kantimathi ◽  
J. A. Alic
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Growth Retardation ◽  
Fretting Fatigue ◽  
Fatigue Tests ◽  
Constant Amplitude ◽  
Axial Loads ◽  
Prolonged Fatigue ◽  
Stress Ratios ◽  
Crack Growth Retardation

Fretting fatigue tests have been conducted on 7075-T7351 aluminum alloy coupons with fretting pads of the same material. Three different stress ratios were used, the otherwise constant amplitude axial loads being interrupted every 1000 cycles by either tensile overloads to 400 MPa or compressive underloads to −200 MPa. Tensile overloads greatly prolonged fatigue life for low stresses where the overload ratios were 1.6 and above; compressive underloads had comparatively little effect. The results are discussed in terms of crack growth retardation phenomena.

scholarly journals Effects of Actual Marine Atmospheric Pre-Corrosion and Pre-Fatigue on the Fatigue Property of 7085 Aluminum Alloy

Metals ◽  
2022 ◽  
Vol 12 (1) ◽  
pp. 81
Author(s):  
Laixin Shi ◽  
Lin Xiang ◽  
Jianquan Tao ◽  
Jun Liu ◽  
Qiang Chen ◽  
...  
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Pitting Corrosion ◽  
Atmospheric Corrosion ◽  
Fatigue Property ◽  
Outdoor Exposure ◽  
Fatigue Tests ◽  
Constant Amplitude ◽  
Fatigue Fractography ◽  
Corrosion Mode

Effects of actual marine atmospheric precorrosion and prefatigue on the fatigue property of 7085-T7452 aluminum alloy were investigated by using the methods of marine atmospheric outdoor exposure tests and constant amplitude axial fatigue tests. Marine atmospheric corrosion morphologies, fatigue life, and fatigue fractography were analyzed. After three months of outdoor exposure, both pitting corrosion and intergranular corrosion (IGC) occurred, while the latter was the dominant marine atmospheric corrosion mode. Marine atmospheric precorrosion could result in a dramatical decrease in the fatigue life of the as-received 7085-T7452 aluminum alloy, while selective prefatigue can improve the total fatigue life of the precorroded specimen. The mechanism of the actual marine atmospheric corrosion and its effects on the fatigue life of the 7085-T7452 aluminum alloy were also discussed.

The Effect of Crack Growth Retardation when Comparing Constant Amplitude to Variable Amplitude Loading in an Aluminium Alloy

2014 ◽  
Vol 891-892 ◽  
pp. 948-954 ◽  
Author(s):  
Madeleine Burchill ◽  
Simon A. Barter ◽  
Michael Jones
Keyword(s):  
Growth Rate ◽  
Fatigue Life ◽  
Crack Growth Rate ◽  
Crack Growth ◽  
Growth Retardation ◽  
Crack Front ◽  
Constant Amplitude ◽  
Variable Amplitude ◽  
Growth Increments ◽  
Crack Growth Retardation

It has often been observed that the growth of short fatigue cracks under variable amplitude (VA) cyclic loading is not well predicted when utilising standard constant amplitude (CA) crack growth rate/stress intensity data (da/dN v DK). This paper outlines a coupon fatigue test program and analyses, investigating a possible cause of crack growth retardation from CA-only testing. Various test loading spectra were developed with sub-blocks of VA and CA cycles, then using quantitative fractography (QF) the sub-block crack growth increments were measured. Comparison of these results found that, after establishing a consistent uniform crack front using a VA load sequence, the average crack growth rate then progressively slowed down with the number of subsequent CA load cycles applied. Further fractographic investigation of the fracture surface at the end of each CA and VA sub-block crack growth, identified significant crack front morphology differences. Thus it is postulated that a variation or deviation from an efficient crack path is a driver of local retardation in short crack growth during CA loading. This may be a source of error in analytical predictions of crack growth under VA spectra loading that may need to be considered in addition to other potential effects such asless closure whilst cracks are small. For aircraft designers, using solely CA data for fatigue life predictions this may result in non-conservative estimates of total crack fatigue life, producing unexpected failures or an increased maintenance burden.

Corrosion Prevention Compound on the Fatigue Life of 2024-T3 Aluminum Alloy

Materials ◽  
2005 ◽  
Author(s):  
M. A. Wahab ◽  
J. H. Park ◽  
S. S. Pang
Keyword(s):  
Aluminum Alloy ◽  
Water Vapor ◽  
Fatigue Life ◽  
Crack Growth ◽  
Fatigue Loading ◽  
Corrosive Environment ◽  
Constant Amplitude ◽  
Corrosion Prevention ◽  
Electron Microscopic ◽  
Stress Ratios

Corrosion-Prevention-Compounds (CPC) are commonly used to prevent corrosion in the aircraft industry. The presence of corrosive environment on aircraft structures has detrimental effects on the aircraft components which reduces the fatigue life and may also accelerate the crack growth rate in the structures. This is an experimental study on 2024-T3 aluminum alloy to investigate the effect of fatigue crack growth (life from threshold crack growth to final failure) using CPC on fatigue life. The corrosion fatigue with the presence of water-vapor reduces the total fatigue life. The fatigue life with the CPC treatment is shown to increase the fatigue life due to the protection from the corrosive environment containing water-vapor. Test results are obtained for various stress ratios and frequencies with and without the CPC treatment under constant amplitude fatigue loading in water vapor. The second aspect of this work is to investigate the effect of periodic overloads and the limitation in their spacing cycles on the fatigue life under constant amplitude fatigue loading. The results confirm the earlier work that the fatigue life increases due to the periodic overloads in 2024-T3 aluminum alloy. The interactions between overloads that are controlled by the spacing cycles between overloads are also examined. From scanning electron microscopic work the transition from the ductile to brittle mode is observed clearly in this experimental work.

Experimental analysis of constant-amplitude fatigue properties in 6156 (Al-Mg-Si) sheet aluminum alloy

2018 ◽  
Vol 53 (8) ◽  
pp. 676-686
Author(s):  
Nikolaos D Alexopoulos ◽  
Evangelos Migklis ◽  
Dimitrios Myriounis
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Aluminum Alloys ◽  
Work Hardening ◽  
Endurance Limit ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Constant Amplitude ◽  
The Matrix ◽  
Fatigue Endurance

Fatigue mechanical behavior of wrought aluminum alloy (Al-Mg-Si) 6156 at T4 temper is experimentally investigated. Constant-amplitude fatigue tests, at fixed stress ratio R = 0.1, were carried out, and the respective stress–life diagram was constructed and compared against the competitive 6xxx aluminum alloys, for example, 6082 and 6061. Fatigue endurance limit of AA6156 was found to be approximately 155 ± 5 MPa, that is, almost 30% below yield stress Rp of the material. AA6156 presents almost 50% higher fatigue life in the high-cycle fatigue area and approximately 20% higher fatigue endurance limit, when compared with other 6xxx series aluminum alloys. Significant work hardening was induced due to fatigue and was experimentally validated by the measurements of residual stiffness of fatigue loops as well as of absorbed energy per fatigue loop. Work-hardening exponent was essentially decreased by almost 25% from the first fatigue cycles and up to 10% of fatigue life. Fracture surfaces of specimens loaded at applied stresses close to fatigue endurance limit exhibited signs of coarse voids due to the formed precipitates at the matrix. The fracture mechanism was a mixture of transgranunal and intergranular fracture for the fatigue specimens tested at higher applied fatigue loadings.

scholarly journals Experimental and numerical investigation into effect of elevated temperature on fretting fatigue behavior

2011 ◽  
Vol 2 (1) ◽  
pp. 2-11
Author(s):  
R. Hojjati Talemi ◽  
M. Soori ◽  
M. Abdel Wahab ◽  
Patrick De Baets
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Elevated Temperature ◽  
Gas Turbines ◽  
Fatigue Behavior ◽  
Surface Oxidation ◽  
Fretting Fatigue ◽  
Growth Increment ◽  
Fatigue Tests ◽  
New Device

t Fretting fatigue damage occurs in contacting parts when they are subjected to fluctuating loadingsand sliding movements at the same time. This phenomenon may occur in many applications such asbearings/ shafts, bolted and riveted connections, steel cables, and steam and gas turbines. In this paper,the effect of elevated temperature on fretting fatigue life of Al7075-T6 is investigated using a new device forfretting fatigue tests with variable crank shaft mechanism. Also a finite element modeling method was usedto estimate crack propagation lifetime in aluminum alloy, Al7075-T6 specimens at elevated temperatureunder fretting condition. In this method, shear and normal stresses that are caused by contact load areupdated at each crack growth increment. Finally, a comparison between the experimental and numericalresults is done in order to evaluate the FE simulation.Department of mechanical engineering, Islamic Azad University, Takestan Branch, Takestan, IranThe experimental results show that: (i) fretting fatigue life of the material increases with temperature up to350°C by 180% for low stresses and decreases by 40% for high stresses, (ii) this fashion of variation offretting fatigue life versus temperature is believed to be due to degradation of material properties whichoccurs by overaging and wear resistance increase due to oxidation of aluminum alloy. While overaginggives rise to degradation of mechanical strength of material and hence the reduction of its fretting fatiguelife, surface oxidation of the specimens brings some improvement of fatigue behavior of the material.Metallurgical examination of the specimens reveals that temperature results in precipitation of impurities ofal-7075-T6. The size of precipitated impurities and their distances gets bigger as temperature increases.This could be a reason for material degradation of specimens which are exposed to heating for longer timeduration.

scholarly journals Multiaxial fatigue behavior of 2618 aluminum alloy

2019 ◽  
Vol 300 ◽  
pp. 09003
Author(s):  
Benaïssa Malek ◽  
Catherine Mabru ◽  
Michel Chaussumier
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Internal Pressure ◽  
Fatigue Behavior ◽  
Fatigue Tests ◽  
Multiaxial Fatigue ◽  
Mean Stress ◽  
Research Project ◽  
Pressure Tests

The purpose of the present research project is to study multiaxial fatigue behavior of 2618 alloy. The influence of mean stress on the fatigue behavior under tension and torsion is particularly investigated. Fatigue tests under combined tensile-torsion, in or out of phase, as well as combined tensile-torsion-internal pressure tests have also been conducted. Multiaxial fatigue results are analyzed according to Fatemi-Socie criterion to predict the fatigue life.

Predicting Fatigue Life of Pre-Corroded LC4 Aluminum Alloy by Artificial Neural Network

2010 ◽  
Vol 118-120 ◽  
pp. 221-225 ◽  
Author(s):  
Cheng Long Xu ◽  
Sheng Li Lv ◽  
Zhen Guo Wang ◽  
Wei Zhang
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Aluminum Alloy ◽  
Fatigue Life ◽  
Network Architecture ◽  
Fatigue Tests ◽  
Data Sets ◽  
Absolute Relative Error ◽  
Artificial Neural ◽  
Artificial Neural Network Ann

The purpose of this work was to predict the fatigue life of pre-corroded LC4 aluminum alloy by applying artificial neural network (ANN). Specimens were exposed to the same corrosive environment for 24h, 48h, and 72h. Fatigue tests were conducted under different stress levels. The existing experimental data sets were used for training and testing the construction of proposed network. A suitable network architecture (2-15-1) was proposed with good performance in this study. For evaluating the method efficiency, the experimental results have been compared to values predicted by ANN. The maximum absolute relative error for predicted values does not exceed 5%. Therefore it can be concluded that using neural networks to predict the fatigue life of LC4 is feasible and reliable.

Relationship Between Fatigue Life Distribution, Notch Configuration, and S-N Curve of a 2024-T4 Aluminum Alloy

1985 ◽  
Vol 107 (3) ◽  
pp. 214-220 ◽  
Author(s):  
T. Shimokawa ◽  
Y. Hamaguchi
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Stress Amplitude ◽  
Fatigue Tests ◽  
Test Results ◽  
Notched Specimens ◽  
Wide Range ◽  
Life Distributions ◽  
The Relationship ◽  
Test Stress

The objective of this study is to identify the most closely related variable to the distribution of fatigue life in unnotched and three kinds of notched 2024-T4 aluminum alloy specimens. Carefully designed fatigue tests under a constant temperature and humidity condition provided fatigue life distributions over a wide range of stress amplitude. This study used about 1000 specimens. On the basis of the test results, the dependence of the scatter in fatigue life on notch configuration, the period to crack initiation, the level of stress amplitude, the median fatigue life, and the slope of the median S-N curve is investigated, and the relationship between the distributional form of fatigue life and the shape of the median S-N curve is discussed. It is concluded that the slope and shape of the median S-N curve in the vicinity of the test stress level are closely related to the scatter and distributional form of fatigue life respectively. This is common to the unnotched and three kinds of notched specimens. A variability hypothesis to correlate the median S-N curve with fatigue life distributions is examined.

scholarly journals IMPROVEMENT OF FATIGUE LIFE OF A HOLED SPECIMEN OF ALUMINUM-ALLOY 2024-T3 BY INDENTATION AND HOLE EXPANSION

2012 ◽  
Vol 06 ◽  
pp. 336-342 ◽  
Author(s):  
MD. SHAFIUL FERDOUS ◽  
CHOBIN MAKABE ◽  
TATSUJIRO MIYAZAKI ◽  
NOBUSUKE HATTORI
Keyword(s):  
Aluminum Alloy ◽  
Fatigue Life ◽  
Crack Growth ◽  
Testing Machine ◽  
Fatigue Tests ◽  
Growth Behavior ◽  
Crack Growth Behavior ◽  
Local Plastic ◽  
Aluminum Alloy 2024 ◽  
Pull Tests

A method of improving the fatigue life and crack growth behavior of a center holed specimen was investigated. Local plastic deformation was applied around the hole by indentation to achieve the purpose. A series of fatigue tests was conducted on aluminum-alloy 2024-T3. Push-pull tests were performed under a stress ratio of R= -1 and a frequency of 10Hz. The observations of the crack initiation and growth were performed with a microscope, and hardness around the hole was measured by Vickers hardness testing machine. In the present study, the longest fatigue life was observed in the case of an indentation specimen with the highest load. The indentation was performed on both sides of the hole edges. The crack growth rate was decreased by indentation or expansion of the material around the hole. From the experimental results, it is found that the fatigue life and crack growth behavior of a holed or notched specimen can be improved by a simple technical method that is related to the local plastic working.

Sign in / Sign up

Export Citation Format

Share Document