Test equipment for fatigue crack growth testing of polymeric materials in chlorinated water at different temperatures

2018 ◽  
Vol 203 ◽  
pp. 44-53 ◽  
Author(s):  
Joerg Fischer ◽  
Patrick R. Bradler ◽  
Reinhold W. Lang
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Polymeric Materials ◽  
Test Equipment ◽  
Different Temperatures ◽  
Fatigue Crack Growth Testing

Effect of Temperature on Fatigue Crack Growth in CPVC

2003 ◽  
Vol 125 (1) ◽  
pp. 71-77 ◽  
Author(s):  
Muhammad Irfan-ul-Haq ◽  
Nesar Merah
Keyword(s):  
Stress Intensity Factor ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Fatigue Crack Growth ◽  
Intensity Factor ◽  
Crack Growth ◽  
Effect Of Temperature ◽  
Stress Intensity Factor Range ◽  
Crack Growth Behavior ◽  
Different Temperatures

This study addresses the effect of temperature on fatigue crack growth (FCG) behavior of CPVC. FCG tests were conducted on CPVC SEN tensile specimens in the temperature range −10 to 70°C. These specimens were prepared from 4-in. injection-molded pipe fittings. Crack growth behavior was studied using LEFM concepts. The stress intensity factor was modified to include the crack closure and plastic zone effects. The effective stress intensity factor range ΔKeff gave satisfactory correlation of crack growth rate (da/dN) at all temperatures of interest. The crack growth resistance was found to decrease with temperature increase. The effect of temperature on da/dN was investigated by considering the variation of mechanical properties with temperature. Master curves were developed by normalizing ΔKeff by fracture strain and yield stress. All the da/dN-ΔK curves at different temperatures were collapsed on a single curve. Crazing was found to be the dominant fatigue mechanism, especially at high temperature, while shear yielding was the dominant mechanism at low temperatures.

scholarly journals Fatigue crack growth testing using varying R-ratios

2010 ◽  
Vol 2 (1) ◽  
pp. 155-161 ◽  
Author(s):  
Magnus Hörnqvist ◽  
Thomas Hansson ◽  
Olle Clevfors
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Fatigue Crack Growth Testing

Effects of Hydrogen on Fatigue Crack Growth of Iron Aluminides

1994 ◽  
Vol 364 ◽  
Author(s):  
A. Castagna ◽  
N.S Stoloff
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Al Alloys ◽  
Moist Air ◽  
Stress Intensity Range ◽  
Low Levels ◽  
Structural Iron ◽  
Fatigue Crack Growth Testing ◽  
Crack Growth Rates

AbstractThree Fe-Al alloys, FAP-Y, FA-129, and Fe-35a%Al, containing 16, 28, and 35a%Al, respectively, have been subjected to fatigue crack growth testing in moist air, in oxygen, and in gaseous hydrogen. In each case hydrogen and air were embrittling. Crack growth rates increased significantly as frequency decreased. Fatigue crack growth results have been compared with those for other structural iron-base alloys. Surprisingly, FAP-Y displays the highest crack growth rate of any alloy examined, except at very low levels of stress intensity range. The mechanisms for embrittlement by hydrogen and by moisture in air are discussed.

Full Size Fatigue Crack-Growth Testing for Girth Welds

2004 ◽  
Author(s):  
Paulo Gioielli ◽  
Jaime Buitrago
Keyword(s):  
Fatigue Crack ◽  
Fatigue Crack Growth ◽  
Crack Growth ◽  
Production Quality ◽  
Small Scale ◽  
Loading Frequency ◽  
Growth Data ◽  
Girth Welds ◽  
Crack Growth Modeling ◽  
Fatigue Crack Growth Testing

Fatigue crack-growth modeling has a significant impact in establishing defect acceptance criteria for the inspection of fracture-critical, girth-welded components, such as risers and tendons. ExxonMobil has developed an experimental technique to generate crack-growth data, in actual welded tubulars, that account for the particular material properties, geometry, and residual stresses. The technique is fully compatible with conventional fracture mechanics models. It uses a series of pre-designed notches made around the welds on a production quality, full-scale specimen that is tested efficiently in a resonant fatigue setup. The crack development from notches is monitored during testing and evaluated post-mortem. Given its simplicity and high loading frequency, the technique provides growth data germane to the component at hand at a lower cost and faster than standard, small-scale tests.

Sign in / Sign up

Export Citation Format

Share Document