Experimental and analytical study of carbon fiber-reinforced polymer (FRP)/autoclaved aerated concrete (AAC) sandwich panels

2009 ◽  
Vol 31 (10) ◽  
pp. 2337-2344 ◽  
Author(s):  
Mohammed A. Mousa ◽  
Nasim Uddin
Keyword(s):  
Carbon Fiber ◽  
Analytical Study ◽  
Sandwich Panels ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Autoclaved Aerated Concrete ◽  
Reinforced Polymer ◽  
Aerated Concrete ◽  
Carbon Fiber Reinforced

New unibody clamp anchors for post-tensioning carbon-fiber-reinforced polymer rods

PCI Journal ◽  
2014 ◽  
Vol 59 (1) ◽  
pp. 103-113 ◽  
Author(s):  
Clayton A. Burningham ◽  
Chris P. Pantelides ◽  
Lawrence D. Reaveley
Keyword(s):  
Carbon Fiber ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced ◽  
Post Tensioning ◽  
Polymer Rods

Restoring Initially Cracked Reinforced Concrete Beams utilizing Carbon Fiber Reinforced Polymer Strips

2019 ◽  
Vol 7 (1) ◽  
pp. 30-34
Author(s):  
A. Ajwad ◽  
U. Ilyas ◽  
N. Khadim ◽  
Abdullah ◽  
M.U. Rashid ◽  
...  
Keyword(s):  
Carbon Fiber ◽  
Concrete Beams ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Fiber Reinforced ◽  
Loading Test ◽  
Control Beam ◽  
Reinforced Polymer ◽  
Cfrp Sheet ◽  
Carbon Fiber Reinforced

Carbon fiber reinforced polymer (CFRP) strips are widely used all over the globe as a repair and strengthening material for concrete elements. This paper looks at comparison of numerous methods to rehabilitate concrete beams with the use of CFRP sheet strips. This research work consists of 4 under-reinforced, properly cured RCC beams under two point loading test. One beam was loaded till failure, which was considered the control beam for comparison. Other 3 beams were load till the appearance of initial crack, which normally occurred at third-quarters of failure load and then repaired with different ratios and design of CFRP sheet strips. Afterwards, the repaired beams were loaded again till failure and the results were compared with control beam. Deflections and ultimate load were noted for all concrete beams. It was found out the use of CFRP sheet strips did increase the maximum load bearing capacity of cracked beams, although their behavior was more brittle as compared with control beam.

Basic Design of High-Speed Riverine Craft Made of Carbon Fiber Reinforced Polymer

2020 ◽  
Vol 57 (4) ◽  
pp. 241-253
Author(s):  
Zhiqiang Han ◽  
Jung-kyu Choi ◽  
Inhyuck Hwang ◽  
Jinyoung Kim ◽  
Daekyun Oh
Keyword(s):  
Carbon Fiber ◽  
High Speed ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Basic Design ◽  
Fiber Reinforced ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

High thermal conductivity carbon fiber reinforced polymer based on a carbon fiber from pitch and dispersed-filled ENPB matrix

2018 ◽  
pp. 130-137
Author(s):  
E. A. Nikolaeva ◽  
A. N. Timofeev ◽  
K. V. Mikhaylovskiy
Keyword(s):  
Thermal Conductivity ◽  
Carbon Fiber ◽  
High Thermal Conductivity ◽  
Fiber Reinforced Polymer ◽  
Carbon Fiber Reinforced Polymer ◽  
Carbon Powder ◽  
Fiber Reinforced ◽  
Thermophysical Characteristics ◽  
Reinforced Polymer ◽  
Carbon Fiber Reinforced

This article describes the results of the development of a high thermal conductivity carbon fiber reinforced polymer based on carbon fiber from pitch and an ENPB matrix modified with a carbon powder of high thermal conductivity. Data of the technological scheme of production and the results of determining the physicomechanical and thermophysical characteristics of carbon fiber reinforced polymer are presented. 

Sign in / Sign up

Export Citation Format

Share Document