Analyses of the effects of channel inclination and rotation on two-phase flow characteristics and pressure drop in a rectangular channel

2019 ◽  
Vol 109 ◽  
pp. 109850 ◽  
Author(s):  
Francisco Loyola Lavín ◽  
Fabio Toshio Kanizawa ◽  
Gherhardt Ribatski
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Two Phase

Correlations of the Holdup and the Frictional Pressure Drop in Air-Water Two-Phase Flow in a Flat Capillary Rectangular Channel

2004 ◽  
Author(s):  
Hideo Ide ◽  
Tohru Fukano
Keyword(s):  
Pressure Drop ◽  
Aspect Ratio ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Flow Characteristics ◽  
Phase Flow ◽  
Two Phase Flows ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Flow Phenomena

Both vertical upward and horizontal gas-liquid two-phase flows in a flat capillary rectangular channel were studied to clarify the flow phenomena, the holdup and the frictional pressure drop. The dimension of the channel used was 9.9 mm × 1.1 mm. The orientations of the channel were with the wide side vertical and the wide side horizontal. The differences between the flow characteristics in such orientations were investigated. New correlations of holdup and frictional pressure drop for flat capillary channels are proposed, in which the effect of aspect ratio has been taken into consideration.

Two-Phase Flow Through Square and Circular Microchannels—Effects of Channel Geometry

2004 ◽  
Vol 126 (4) ◽  
pp. 546-552 ◽  
Author(s):  
Peter M.-Y. Chung ◽  
Masahiro Kawaji ◽  
Akimaro Kawahara ◽  
Yuichi Shibata
Keyword(s):  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Flow Characteristics ◽  
Separated Flow ◽  
Phase Flow ◽  
Two Phase ◽  
Channel Geometry ◽  
Frictional Pressure Drop ◽  
Channel Shape

An adiabatic experiment was conducted to investigate the effect of channel geometry on gas-liquid two-phase flow characteristics in horizontal microchannels. A water-nitrogen gas mixture was pumped through a 96 μm square microchannel and the resulting flow pattern, void fraction and frictional pressure drop data were compared with those previously reported by the authors for a 100 μm circular microchannel. The pressure drop data were best estimated using a separated-flow model and the void fraction increased non-linearly with volumetric quality, regardless of the channel shape. However, the flow maps exhibited transition boundaries that were shifted depending on the channel shape.

Experimental Investigation of the Effect of Surface Tension and the Correlation on Void Fraction and Frictional Pressure Drop of an Air-Liquid Two-Phase Flow in a Horizontal Flat Capillary Rectangular Channel

2003 ◽  
Author(s):  
Hideo Ide ◽  
Tohru Fukano
Keyword(s):  
Surface Tension ◽  
Pressure Drop ◽  
Void Fraction ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Surfactant Solution ◽  
Phase Flow ◽  
Two Phase ◽  
Frictional Pressure Drop ◽  
Effect Of Surface

Air-liquid two-phase flow in a horizontal flat capillary rectangular channel has been studied to clarify the effects of concentration of surfactant solution on the flow phenomena, such as flow patterns, pressure drop, void fraction and so on. The concentrations of surfactant solution were 0, 10, 50 and 100 ppm and the surface tension of each solution was reduced to about 34mN/m from that of pure water of about 72mN/m. The dimension of the channel used was 10.0 mm × 1.0 mm. The drag reduction by mixing the surfactant was examined in both the single phase flow and the two-phase flow. The experimental data of two-phase frictional pressure drop and holdup were compared with the respective correlations which were previously proposed by the other researchers and the present authors. Finally, we proposed new correlations of two-phase frictional pressure drop and holdup in which the effect of surface tension and the aspect ratio of cross section of channel were taken into account.

Experimental Research on Pulsating Two-Phase Flow Pressure Drop Characteristics in Horizontal Rectangular Channel

2014 ◽  
Author(s):  
Siqi Zhang ◽  
Puzhen Gao
Keyword(s):  
Pressure Drop ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Phase Flow ◽  
Two Phase ◽  
Mean Values ◽  
Water Mass Flow Rate

In spite of most previous studies since 1970, the theory of pulsating pipe flows supported by experimental investigations has not yet completed in comparison with the well-defined theory of steady pipe flows. Therefore, it seems that there is much to be done about experimental research in this field. In order to determine the resistance characteristics of two-phase flow under pulsatile conditions, an experimental investigation on two-phase flow with periodically fluctuating flow rates in a narrow rectangular channel is carried out. A frequency inverter is used to obtain experimental conditions with different fluctuating frequencies, amplitudes and mean values of water mass flow rate. After obtaining experimental results, comparisons between experimental frictional pressure drop values and theoretical calculations have been done. Two-phase flow on pulsating conditions is far more complicated than that on steady conditions because pulsating flow is composed of two parts: a steady component and a superimposed periodical time varying component called oscillation. In this paper, the influence of different fluctuating frequencies, amplitudes and mean values of liquid and gas mass flow rate on two-phase flow pressure drop characteristics is also discussed. The results show that the total pressure drop and water mass flow rate change with the same fluctuating period except for a phase difference. The phase lag also changes with the fluctuating frequencies and amplitude. The accelerating pressure drop changes dramatically in a fluctuating period, especially at the end of acceleration. Also, the time when the acceleration pressure drop has its maximum value lags the time when the acceleration reaches its peak, mainly because of the inertial of the fluid.

scholarly journals Experimental investigation of the two-phase flow regimes and pressure drop in horizontal mini-size rectangular test section

2012 ◽  
Vol 33 (2) ◽  
pp. 47-65
Author(s):  
Amr Mohamed Elazhary ◽  
Hassan M. Soliman
Keyword(s):  
Pressure Drop ◽  
Flow Regime ◽  
Test Section ◽  
Two Phase Flow ◽  
Rectangular Cross Section ◽  
Rectangular Channel ◽  
Flow Regimes ◽  
Phase Flow ◽  
Two Phase ◽  
Inlet Conditions

Abstract An experimental study was conducted in order to investigate two-phase flow regimes and fully developed pressure drop in a mini-size, horizontal rectangular channel. The test section was machined in the form of an impacting tee junction in an acrylic block (in order to facilitate visualization) with a rectangular cross-section of 1.87-mm height on 20-mm width on the inlet and outlet sides. Pressure drop measurement and flow regime identification were performed on all three sides of the junction. Air-water mixtures at 200 kPa (abs) and room temperature were used as the test fluids. Four flow regimes were identified visually: bubbly, plug, churn, and annular over the ranges of gas and liquid superficial velocities of 0.04 ≤ JG ≤ 10 m/s and 0.02 ≤ JL ≤ 0.7 m/s, respectively, and a flow regime map was developed. Accuracy of the pressure-measurement technique was validated with single-phase, laminar and turbulent, fully developed data. Two-phase experiments were conducted for eight different inlet conditions and various mass splits at the junction. Comparisons were conducted between the present data and former correlations for the fully developed two-phase pressure drop in rectangular channels with similar sizes. Wide deviations were found among these correlations, and the correlations that agreed best with the present data were identified.

Pressure Drop Characteristics of R134a Two-Phase Flow in a Horizontal Rectangular Microchannel

2002 ◽  
Author(s):  
X. Tu ◽  
P. Hrnjak
Keyword(s):  
Pressure Drop ◽  
Two Phase Flow ◽  
Rectangular Channel ◽  
Homogeneous Model ◽  
Saturation Temperature ◽  
Phase Flow ◽  
Two Phase ◽  
Rectangular Microchannel ◽  
Turbulent Flow Regime ◽  
Parameter Ranges

Adiabatic two-phase flow pressure drop of R134a have been investigated experimentally in a rectangular channel with hydraulic diameter of 0.14 mm. Single-phase flow experiments were also conducted with liquid and vapor R134a, and an empirical correlation was developed for the turbulent flow regime. The parameter ranges examined for two-phase flow are: mass flux from 158 to 785 kg m−2 s−1; vapor quality from 0.01 to 0.95; and saturation temperature at about 24 ~ 32°C. The experimental data were compared with twelve existing correlations. The homogeneous model and the Mishima and Hibiki (1996) correlation give better predictions than any other correlations.

Sign in / Sign up

Export Citation Format

Share Document