Pressure Change for Single- and Two-Phase Non-Newtonian Flows through Sudden Contraction in Rectangular Microchannel

The flow characteristics of the single-phase liquid and the gas–liquid two-phase flows including the Newtonian and non-Newtonian liquids were experimentally investigated in a horizontal rectangular micro-channel with a sudden contraction—specifically the pressure change across the contraction. The rectangular cross-sectional dimension has Wu × Hu (width × height) = 0.99 × 0.50 mm2 on the upstream side of the contraction and Wd × Hd = 0.49 × 0.50 mm2 on the downstream side. The resulting contraction ratio, σA (=Wd/Wu), was 0.5. Air was used as the test gas (in the case of the gas–liquid two-phase flow experiment), distilled water and three kinds of aqueous solution, i.e., glycerin 25 wt%, xanthangum 0.1 wt% and polyacrylamide 0.11 wt% were used as the test liquid. The pressure distribution in the flow direction upstream and downstream of the channel was measured. The pressure change and loss at the sudden contraction were determined from the pressure distribution. In addition, the pressure change data were compared with the calculation by several correlations proposed by various researchers as well as a newly developed correlation in this study. From the comparisons, it was found that calculations by the newly developed correlations agreed well with the measured values within the error of 30%.

Modelling corners flow in rectangular microchannel

Rectangular microchannels are most common configuration in microfluidics. They can be used in many industries, for example in lab-on-chip devices. Despite standard fluid dynamics, microfluidics has a significant impact of wall boundary conditions on fluid flow. And in microfluidics, we cannot simply set no-slip boundary conditions if our goal is accurate modeling results. In rectangular microchannels, there is another important moment in modeling that is not present in circular pipes. The velocity profile of the fluid depends on the shear stress at the edges and the velocities at the walls of the microchannel change at different points of the cross-sectional wall of the microchannel. The fluid velocity is lower at the corners of a rectangular microchannel. In this paper, a solution is proposed to find a more accurate way to model the fluid flow in a rectangular microchannel by knowing the friction factor without shear stress distribution.

Experimental study of wavy-annular flow in a rectangular microchannel using LIF method

This article aims at studying gas-liquid flow in a rectangular microchannel with a high aspect ratio (200 × 2045 μm). Liquid and gas phases were 95% ethanol and nitrogen mixture. Experimental flow characteristics are obtained using high-speed visualization and laser-induced fluorescence (LIF) methods. Using the LIF method for wavy-annular flow, the average film thickness, liquid film distribution, and liquid film width were measured. The dependences of the liquid film width and the average film thickness on gas superficial velocity are presented in graphical form and analyzed. An increase in gas superficial velocity causes growth of the liquid film width and thickness of the liquid film, which indicates the process of liquid transfer from the menisci area to the liquid film. For different liquid velocities and the same gas superficial velocities, close values of averaged liquid film thickness were observed for flow with 2D waves and 3D waves on liquid film.

Constructal Optimization of Rectangular Microchannel Heat Sink with Porous Medium for Entropy Generation Minimization

A model of rectangular microchannel heat sink (MCHS) with porous medium (PM) is developed. Aspect ratio of heat sink (HS) cell and length-width ratio of HS are optimized by numerical simulation method for entropy generation minimization (EGM) according to constructal theory. The effects of inlet Reynolds number (Re) of coolant, heat flux on bottom, porosity and volume proportion of PM on dimensionless entropy generation rate (DEGR) are analyzed. From the results, there are optimal aspect ratios to minimize DEGR. Given the initial condition, DEGR is 33.10% lower than its initial value after the aspect ratio is optimized. With the increase of Re, the optimal aspect ratio declines, and the minimum DEGR drops as well. DEGR gets larger and the optimal aspect ratio remains constant with the increasing of heat flux on bottom. For the different volume proportion of PM, the optimal aspect ratios are diverse, but the minimum DEGR almost stays unchanged. The twice minimized DEGR, which results from aspect ratio and length-width ratio optimized simultaneously, is 10.70% lower than the once minimized DEGR. For a rectangular bottom, a lower DEGR can be reached by choosing the proper direction of fluid flow.

Application of the laser-induced fluorescence to study local characteristics of a gas-liquid flow in rectangular microchannel

The Laser-Induced Fluorescence (LIF) method was used to characterize liquid phase distribution in rectangular slit microchannel with cross-section 200×1205 μm for horizontal gas-liquid flow. Ethanol and nitrogen were used as working liquid and gas accordingly. The feature of this study is an application of hydraulic focusing cross-junction mixer for obtaining elongated bubble and transition flows in the microchannel with a high aspect ratio. Using LIF measurements for elongated bubble and transition flows the liquid film distributions were obtained for different distances from the bubble top and average liquid film thickness was compared with the prediction according to Taylor’s law.