Derivation of the exact stiffness matrix of shear-deformable multi-layered beam element in partial interaction

2016 ◽  
Vol 112 ◽  
pp. 40-49 ◽  
Author(s):  
Pisey Keo ◽  
Quang-Huy Nguyen ◽  
Hugues Somja ◽  
Mohammed Hjiaj
Keyword(s):  
Stiffness Matrix ◽  
Beam Element ◽  
Partial Interaction ◽  
Layered Beam ◽  
Exact Stiffness Matrix ◽  
Shear Deformable

scholarly journals Frame on Elastic Foundation / Rám Na Pružnom Podloží

2012 ◽  
Vol 12 (2) ◽  
pp. 216-224
Author(s):  
Katarína Tvrdá
Keyword(s):  
Elastic Foundation ◽  
Stiffness Matrix ◽  
Beam Element ◽  
Winkler Foundation ◽  
Displacement Method ◽  
Exact Stiffness Matrix

Abstract This article deals with calculation of the beam and frame rested on elastic foundation using matrix displacement method. An exact stiffness matrix of a beam element on elastic foundation is formulated. The beam is rested on elastic Winkler foundation. At the end off paper, same results of frame on elastic foundation are presented.

Geometrical Stiffness of Thin-Walled I-Beam Element Based on Rigid-Beam Assemblage Concept

2012 ◽  
Vol 28 (1) ◽  
pp. 97-106 ◽  
Author(s):  
J. D. Yau ◽  
S.-R. Kuo
Keyword(s):  
Stiffness Matrix ◽  
Virtual Work ◽  
Bending Moment ◽  
Beam Element ◽  
Narrow Beam ◽  
Cross Sectional ◽  
Geometric Stiffness ◽  
Buckling Behavior ◽  
Post Buckling ◽  
Thin Walled

ABSTRACTUsing conventional virtual work method to derive geometric stiffness of a thin-walled beam element, researchers usually have to deal with nonlinear strains with high order terms and the induced moments caused by cross sectional stress results under rotations. To simplify the laborious procedure, this study decomposes an I-beam element into three narrow beam components in conjunction with geometrical hypothesis of rigid cross section. Then let us adopt Yanget al.'s simplified geometric stiffness matrix [kg]12×12of a rigid beam element as the basis of geometric stiffness of a narrow beam element. Finally, we can use rigid beam assemblage and stiffness transformation procedure to derivate the geometric stiffness matrix [kg]14×14of an I-beam element, in which two nodal warping deformations are included. From the derived [kg]14×14matrix, it can take into account the nature of various rotational moments, such as semi-tangential (ST) property for St. Venant torque and quasi-tangential (QT) property for both bending moment and warping torque. The applicability of the proposed [kg]14×14matrix to buckling problem and geometric nonlinear analysis of loaded I-shaped beam structures will be verified and compared with the results presented in existing literatures. Moreover, the post-buckling behavior of a centrally-load web-tapered I-beam with warping restraints will be investigated as well.

An Exact Three-Dimensional Beam Element With Nonuniform Cross Section

2010 ◽  
Vol 77 (6) ◽  
Author(s):  
M. Jafari ◽  
M. J. Mahjoob
Keyword(s):  
Cross Section ◽  
Stiffness Matrix ◽  
Degrees Of Freedom ◽  
Direct Method ◽  
Three Dimensional ◽  
Curved Beams ◽  
Element Analysis ◽  
Shear Loads ◽  
Line Passing ◽  
Exact Stiffness Matrix

In this paper, the exact stiffness matrix of curved beams with nonuniform cross section is derived using direct method. The considered element has two nodes and 12 degrees of freedom, with three forces and three moments applied at each node. The noncoincidence effect of shear center and center of area is also considered in this element. The deformations of the beam are due to bending, torsion, tensile, and shear loads. The line passing through center of area is a general three-dimensional curve and the cross section properties may change arbitrarily along it. The method is extended to deal with distributed loads on the curved beams. The stiffness matrix of some selected types of beams is determined by this method. The results are compared (where possible) with previously published results, simple beam finite element analysis and analytic solution. It is shown that the determined stiffness matrix is exact and that any type of beam can be analyzed by this method.

Incorporation of Spinal Flexibility Measurements Into Finite Element Analysis

1990 ◽  
Vol 112 (4) ◽  
pp. 481-483 ◽  
Author(s):  
Mack G. Gardner-Morse ◽  
Jeffrey P. Laible ◽  
Ian A. F. Stokes
Keyword(s):  
Experimental Data ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Stiffness Matrix ◽  
Beam Element ◽  
Technical Note ◽  
Element Analysis ◽  
Spinal Motion ◽  
Spinal Flexibility

This technical note demonstrates two methods of incorporating the experimental stiffness of spinal motion segments into a finite element analysis of the spine. The first method is to incorporate the experimental data directly as a stiffness matrix. The second method approximates the experimental data as a beam element.

Sign in / Sign up

Export Citation Format

Share Document